26 m射电望远镜副面调整机构误差分析

doi:10.7527/S1000-6893.2019.23271

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

26 m射电望远镜副面调整机构误差分析

古丽加依娜·哈再孜汗^1,2, 项斌斌¹, 王娜¹, 艾力·玉苏甫¹, 陈卯蒸¹, 李宁^1,2, 薛飞¹

1. 中国科学院新疆天文台, 乌鲁木齐 830011;
2. 中国科学院大学, 北京 100049

收稿日期:2019-07-05 修回日期:2019-11-01 出版日期:2020-04-15 发布日期:2019-10-31
通讯作者: 项斌斌 E-mail:xiangbinbin@xao.ac.cn
基金资助:
国家973计划（2015CB857100）；中国科学院西部之光（2017-XBQNXZ-B-021）；国家自然科学基金（11803078）

Errors analysis of a subreflector adjustment mechanism for NSRT

GULJAINA Kazezkhan^1,2, XIANG Binbin¹, WANG Na¹, AILI Yusup¹, CHEN Maozheng¹, LI Ning^1,2, XUE Fei¹

1. Xinjiang Astronomical Observatory, Chinese Academic of Sciences, Urumqi 830011, China;
2. University of Chinese Academy of Sciences, Beijing 100049, China

Received:2019-07-05 Revised:2019-11-01 Online:2020-04-15 Published:2019-10-31
Supported by:
National Basic Research Program of China (2015CB857100); Light of West China (2017-XBQNXZ-B-021); National Natural Science Foundation of China (11803078)

摘要/Abstract

摘要： 新疆乌鲁木齐南山26 m射电望远镜（NSRT）采用 Stewart 并联机构实现副反射面（简称副面）五自由度运动调整。为确保并联机构的运动精度能满足射电望远镜高精度的指向要求，对影响副面调整机构运动精度的各项误差进行了分析。几何误差模拟结果显示，为使并联机构达到要求的精度，应保证杆长误差小于0.08 mm，铰链误差小于0.04 mm。通过对实测结果与仿真结果分析比较，得出回零误差是造成并联机构误差的主要原因。由于并联机构的回零检测装置主要由增量式编码器与限位开关组成，其中限位开关反馈信号的异常，会引起并联机构的回零误差，分析得到该因素是造成NSRT副面并联机构工作偏差的主要原因，这对并联机构的误差补偿具有指导意义。

关键词: 射电望远镜, 天线副反射面调整, Stewart 平台, 误差分析, 精度

Abstract: The Nan Shan 26 m Radio Telescope (NSRT) in Urumqi, Xinjiang, uses the Stewart platform to adjust the position of subreflector in five degrees of freedom. In order to ensure the Stewart platform has high accuracy to meet the high-precision operation requirements of radio telescope, this paper analyzes the errors that affect the accuracy of the Stewart platform. Geometric error simulation results show that in order to achieve the required accuracy, the errors of the leg length and universal joint should be less than 0.08 mm and 0.04 mm. The comparative analysis of the measured data and the simulated data show that the homing error is the main cause of the error of the Stewart platform. Since the homing detection device of the Stewart platform is mainly composed of incremental encoder and limit switch, the abnormal feedback signal of the limit switch will cause the homing error of the Stewart platform. The paper concludes that this factor is the main reason for the working deviation of the Stewart platform for NSRT, which has guiding significance for the error compensation of the Stewart platform.

Key words: radio telescope, adjusting of subreflector, Stewart platform, error analysis, precision

中图分类号:

TH751

古丽加依娜·哈再孜汗, 项斌斌, 王娜, 艾力·玉苏甫, 陈卯蒸, 李宁, 薛飞. 26 m射电望远镜副面调整机构误差分析[J]. 航空学报, 2020, 41(4): 423271-423271.

GULJAINA Kazezkhan, XIANG Binbin, WANG Na, AILI Yusup, CHEN Maozheng, LI Ning, XUE Fei. Errors analysis of a subreflector adjustment mechanism for NSRT[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(4): 423271-423271.

参考文献 25

[1]	STEWART D. A platform with six degrees of freedom[J]. Proceedings of the Institution of Mechanical Engineers, 1965, 180(1):371-386.
[2]	MERLET J P. Jacobian, manipulability, condition number and accuracy of parallel robots[J]. Journal of Mechanical Design, 2006, 28(1):175-184.
[3]	MERLET J P. Parallel manipulators:State of the art and perspectives[J]. Advanced Robotics, 1993, 8(6):589-596.
[4]	HUNT K H. Structural kinematics of in parallel actuated robot arms[J]. ASME Journal of Mechanisms, Transmissions and Automation in Design, 1983, 105(4):705-712.
[5]	JAFARI F, MCINROY J E. Orthogonal Gough-Stewart platforms for micromanipulation[J]. IEEE Transactions on Robotics&Automation, 2003, 19(4):595-603.
[6]	WOOTTEN A, THOMPSON A R. The Atacama large millimeter/submillimeter array[J]. Proceedings of the IEEE, 2009, 97(8):1463-1471.
[7]	JEWELL P R. The green bank telescope[J]. Proceedings of the IEEE, 2009, 97(8):1382-1390.
[8]	WIELEBINSKI R. The Effelsberg 100 m radio telescope[J]. Naturwissenschaften, 1971, 58(3):109-116.
[9]	SU Y X, DUAN B Y, NAN R D, et al. Mechatronics design of stiffness enhancement of the feed supporting system for the square-kilometer array[J]. IEEE/ASME Transactions on Mechatronics, 2004, 8(4):425-430.
[10]	YANG D H, CHENG Y, WU C C, et al. A novel hexapod and its prototype for secondary mirror alignment in telescopes[J]. Research in Astronomy and Astrophysics, 2018, 18(9):115-124.
[11]	段艳宾,李建军,侯雨雷,等.射电望远镜天线副反射面并联调整机构设计[J].机械设计与制造, 2013(8):222-225. DUAN Y B, LI J J, HOU Y L, et al.Configuration design of the adjusting parallel mechanism for sub-reflector of antenna of radio telescope antenna[J].Machinery Design&Manufacture,2013(8):222-225(in Chinese).
[12]	MASORY O, WANG J, ZHUANG H. Kinematic modeling and calibration of a Stewart platform[J]. Advanced Robotics:the International Journal of the Robotics Society of Japan, 1997, 11(5):519-539.
[13]	PATEL A J, EHMANN K F. Volumetric error analysis of a Stewart platform based machine tool[J]. CIRP Annals-Manufacturing Technology, 1997, 46(1):287-290.
[14]	WANG S M, EHMANN K F. Error model and accuracy analysis of a six-DOF Stewart platform[J]. Journal of Manufacturing Science and Engineering, 2002, 124(2):286-295.
[15]	JELENKOVIC'L, BUDIN L. Error analysis of a Stewart platform based manipulators[J]. Journal of Sociology, 2002, 45(1):26-28.
[16]	TISCHLER C R, SAMUEL A E. Advances in robot kinematics:Analysis and control[M]. Dordrecht:Springer, 1998:227-236.
[17]	POTT A, HILLER M. A new approach to error analysis in parallel kinematic structures[C]//Proceedings of 4th Parallel Kinematics Seminar, 2004:123-136.
[18]	AHMAD A, ANDERSSON K, SELLGREN U, et al. A stiffness modeling methodology for simulation-driven design of haptic devices[J]. Engineering with Computers, 2014, 30(1):125-141.
[19]	ZHOU X, ZHOU F, WANG Y. Pose error modeling and analysis for 6-DOF Stewart platform[C]//2017 Chinese Automation Congress (CAC), 2017:6470-6475.
[20]	李健,李帅,张豪,等.仿咬合Stewart并联机器人模拟与误差分析[J].计算机仿真, 2018, 35(6):343-349. LI J, LI S, ZHANG H. Stewart parallel robot for simulated occlusal movement and error analysis[J]. Computer Simulation, 2018, 35(6):343-349(in Chinese).
[21]	姚蕊,李庆伟,孙京海,等. FAST望远镜馈源舱精度分析研究[J].机械工程学报, 2017, 53(17):50-56. YAO R, LI Q W, SUN J H, et al. Accuracy analysis on focus cabin of FAST[J]. Journal of Mechanical Engineering, 2017, 53(17):50-56(in Chinese).
[22]	李毅.高速并联机械手运动学标定方法研究[D].天津:天津大学, 2009. LI Y. Kinematic calibration method for high-speed parallel robot[D]. Tianjin:Tianjin University, 2009(in Chinese).
[23]	郭云鹏,陈柏,吴洪涛.一种六自由度海浪模拟并联平台的零点标定与性能评估[J].机电工程, 2015, 32(2):169-174. GUO Y P, CHEN B, WU H T. Zero calibration and performance assessment of a 6-DOF parallel platform used for wave simulation[J]. Mechanical&Electrical Engineering Magazine, 2015, 32(2):169-174(in Chinese).
[24]	孙月海,王兰,梅江平,等.基于单目视觉的Delta机器人零点标定方法[J].天津大学学报(自然科学与工程技术版), 2013, 46(3):239-243. SUN Y H, WANG L, MEI J P, et al. Zero calibration of delta robot based on monocular vision[J]. Journal of Tianjin University (Science and Technology), 2013, 46(3):239-243(in Chinese).
[25]	汪劲松,白杰文,高猛,等. Stewart平台铰链间隙的精度分析[J].清华大学学报(自然科学版), 2002, 42(6):758-761. WANG J S, BAI J W, GAO M, et al. Accuracy analysis of joint-clearances in a Stewart platform[J]. Journal of Tsinghua University (Science and Technology), 2002, 42(6):758-761(in Chinese).

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

26 m射电望远镜副面调整机构误差分析

Errors analysis of a subreflector adjustment mechanism for NSRT

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 25

相关文章 15

编辑推荐

Metrics

本文评价

[1]	吴文昌, 马燕凯, 韩省思, 闵耀兵, 燕振国. 一种光滑型TENO非线性加权的WCNS格式[J]. 航空学报, 2024, 45(8): 129052-129052.
[2]	宋海浪, 张建东, 史国庆, 杨啟明, 张耀中. 航空火控系统试飞综合评估技术与方法探讨[J]. 航空学报, 2024, 45(5): 529687-529687.
[3]	杨卫平. 新一代飞行器导航制导与控制技术发展趋势[J]. 航空学报, 2024, 45(5): 529720-529720.
[4]	农历, 盛子帅, 冼军, 张怀宝. 基于高精度算法的结冰翼型分离流动数值模拟[J]. 航空学报, 2023, 44(S2): 729291-729291.
[5]	车沣竺, 米长伟, 张昊平, 张鑫. 基于标量化处理的协同航弹高精度导航系统[J]. 航空学报, 2023, 44(S1): 727632-727632.
[6]	丁继成, 何欣庭, 裴天炜, 杨皓. 矢量结构对载波相位的预测[J]. 航空学报, 2023, 44(S1): 727403-727403.
[7]	马崇立, 刘景源. 网格对高超声速钝头体表面热流数值模拟结果的影响[J]. 航空学报, 2023, 44(5): 126710-126710.
[8]	王维民, 户东方. 旋转叶片动应力非接触测量方法研究综述[J]. 航空学报, 2023, 44(22): 28516-028516.
[9]	巴晓甫, 薛红前, 李西宁. 随位串联三坐标定位器定位精度建模与试验[J]. 航空学报, 2023, 44(19): 428469-428469.
[10]	张攀, 汪勇, 钟凯, 蒋建军, 杨武飞, 李中伟. 图像灰度和相位信息耦合的化铣胶膜刻型三维测量方法[J]. 航空学报, 2023, 44(17): 428212-428212.
[11]	郭飞燕, 刘检华, 肖庆东, 肖世宏, 王仲奇. 数字化装配工装工作状态监测评估及适应性控制技术[J]. 航空学报, 2023, 44(16): 427914-427914.
[12]	王圣业, 邓小刚, 董义道, 王东方, 蔡佳鸿. 面向工程湍流的高精度数值方法[J]. 航空学报, 2023, 44(15): 528728-528728.
[13]	张士峰, 李俊, 杨华波. 惯性制导工具误差分离技术综述[J]. 航空学报, 2023, 44(15): 528590-528590.
[14]	樊茂, 汤亮, 关新, 张科备. 附加连接对主动指向超静平台控制效果的影响[J]. 航空学报, 2023, 44(11): 225864-225864.
[15]	张宝振, 王汉平, 徐峰, 吴志青. VSV调节机构的仿真提速和精度补偿措施[J]. 航空学报, 2022, 43(9): 226034-226034.