航空学报 > 2020, Vol. 41 Issue (4): 423271-423271   doi: 10.7527/S1000-6893.2019.23271

26 m射电望远镜副面调整机构误差分析

古丽加依娜·哈再孜汗1,2, 项斌斌1, 王娜1, 艾力·玉苏甫1, 陈卯蒸1, 李宁1,2, 薛飞1   

  1. 1. 中国科学院 新疆天文台, 乌鲁木齐 830011;
    2. 中国科学院大学, 北京 100049
  • 收稿日期:2019-07-05 修回日期:2019-11-01 出版日期:2020-04-15 发布日期:2019-10-31
  • 通讯作者: 项斌斌 E-mail:xiangbinbin@xao.ac.cn
  • 基金资助:
    国家973计划(2015CB857100);中国科学院西部之光(2017-XBQNXZ-B-021);国家自然科学基金(11803078)

Errors analysis of a subreflector adjustment mechanism for NSRT

GULJAINA Kazezkhan1,2, XIANG Binbin1, WANG Na1, AILI Yusup1, CHEN Maozheng1, LI Ning1,2, XUE Fei1   

  1. 1. Xinjiang Astronomical Observatory, Chinese Academic of Sciences, Urumqi 830011, China;
    2. University of Chinese Academy of Sciences, Beijing 100049, China
  • Received:2019-07-05 Revised:2019-11-01 Online:2020-04-15 Published:2019-10-31
  • Supported by:
    National Basic Research Program of China (2015CB857100); Light of West China (2017-XBQNXZ-B-021); National Natural Science Foundation of China (11803078)

摘要: 新疆乌鲁木齐南山26 m射电望远镜(NSRT)采用 Stewart 并联机构实现副反射面(简称副面)五自由度运动调整。为确保并联机构的运动精度能满足射电望远镜高精度的指向要求,对影响副面调整机构运动精度的各项误差进行了分析。几何误差模拟结果显示,为使并联机构达到要求的精度,应保证杆长误差小于0.08 mm,铰链误差小于0.04 mm。通过对实测结果与仿真结果分析比较,得出回零误差是造成并联机构误差的主要原因。由于并联机构的回零检测装置主要由增量式编码器与限位开关组成,其中限位开关反馈信号的异常,会引起并联机构的回零误差,分析得到该因素是造成NSRT副面并联机构工作偏差的主要原因,这对并联机构的误差补偿具有指导意义。

关键词: 射电望远镜, 天线副反射面调整, Stewart 平台, 误差分析, 精度

Abstract: The Nan Shan 26 m Radio Telescope (NSRT) in Urumqi, Xinjiang, uses the Stewart platform to adjust the position of subreflector in five degrees of freedom. In order to ensure the Stewart platform has high accuracy to meet the high-precision operation requirements of radio telescope, this paper analyzes the errors that affect the accuracy of the Stewart platform. Geometric error simulation results show that in order to achieve the required accuracy, the errors of the leg length and universal joint should be less than 0.08 mm and 0.04 mm. The comparative analysis of the measured data and the simulated data show that the homing error is the main cause of the error of the Stewart platform. Since the homing detection device of the Stewart platform is mainly composed of incremental encoder and limit switch, the abnormal feedback signal of the limit switch will cause the homing error of the Stewart platform. The paper concludes that this factor is the main reason for the working deviation of the Stewart platform for NSRT, which has guiding significance for the error compensation of the Stewart platform.

Key words: radio telescope, adjusting of subreflector, Stewart platform, error analysis, precision

中图分类号: