固体燃料冲压发动机自持燃烧的影响因素

doi:10.7527/S1000-6893.2016.0301

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

固体燃料冲压发动机自持燃烧的影响因素

巩伦昆, 陈雄, 李唯暄, 杨海涛, 周长省

南京理工大学机械工程学院, 南京 210094

收稿日期:2016-09-28 修回日期:2016-10-25 出版日期:2017-07-15 发布日期:2016-12-13
通讯作者: 陈雄,E-mail:chenxiong@njust.edu.cn E-mail:chenxiong@njust.edu.cn
基金资助:
总装备部预先研究项目（404040301）

Influencing factors for self-sustained combustion of solid fuel ramjet

GONG Lunkun, CHEN Xiong, LI Weixuan, YANG Haitao, ZHOU Changsheng

School of Mechanical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China

Received:2016-09-28 Revised:2016-10-25 Online:2017-07-15 Published:2016-12-13
Supported by:
General Armaments Department Pre-research Foundation (404040301)

摘要/Abstract

摘要：

采用试验和仿真方法，研究了固体燃料冲压发动机（SFRJ）自持燃烧的主要影响因素。研究结果表明：SFRJ内为典型的扩散火焰，化学反应特征时间与反应物停留特征时间的比值是影响发动机自持燃烧的关键参数，该值越小，扩散火焰越稳定；本文研究工况下，较小的后台阶高度即可保证发动机实现自持燃烧，后台阶稳定火焰的物理原因是在固体燃料表面附近形成一个低速区，保证了固体燃料的分解燃烧，当台阶高度为0时，由于化学反应特征时间与反应物停留特征时间的比值迅速增加，SFRJ无法自持燃烧；台阶高度较小时，点火过程会对SFRJ的稳定燃烧产生影响，SFRJ可能会出现熄火复燃现象。

关键词: 冲压发动机, 固体燃料, 自持燃烧, 后台阶, 直连式试验, 数值仿真

Abstract:

By simulation and test, the parameters which influence the self-sustained combustion of the solid fuel ramjet (SFRJ) are investigated. The results show that the combustion in SFRJ is diffusion-controlled, and the ratio of characteristic chemical reaction time to characteristic residence time is the critical parameter influencing the self-sustained combustion of ramjet. The smaller the ratio is, the more stable the flame will be. Under the conditions of the present research, a small step height can guarantee the self-sustained combustion of ramjet. The physical reason for the stabilization of combustion behind a backward-facing step is that existence of a low speed flow area near the solid fuel surface guarantees the pyrolysis and combustion of the solid fuel. When the step height is 0, the flame will go out as the ratio of characteristic chemical reaction time to characteristic residence time increases quickly. When the step height is small, the ignition process may have influence on stable combustion of the SFRJ, and reburning may occur after flameout.

Key words: ramjet, solid fuel, self-sustained combustion, backward-facing step, direct-connect test, numerical simulation

中图分类号:

V235

巩伦昆, 陈雄, 李唯暄, 杨海涛, 周长省. 固体燃料冲压发动机自持燃烧的影响因素[J]. 航空学报, doi: 10.7527/S1000-6893.2016.0301.

GONG Lunkun, CHEN Xiong, LI Weixuan, YANG Haitao, ZHOU Changsheng. Influencing factors for self-sustained combustion of solid fuel ramjet[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, doi: 10.7527/S1000-6893.2016.0301.

参考文献

[1] 鲍福廷, 黄熙君, 张振鹏, 等. 固体火箭冲压发动机[M]. 北京: 中国宇航出版社, 2006: 25-31. BAO F T, HUANG X J, ZHANG Z P, et al. Integral solid propellant ramjet rocket motor[M]. Beijing: China Astronautic Publishing House, 2006: 25-31 (in Chinese).
[2] ELANDS P J M, KORTING P G, WIJCHERS T, et al. Comparison of combustion experiments and theory in polyethylene solid fuel ramjets[J]. Journal of Propulsion and Power, 1990, 6(6): 732-739.
[3] FERREIRA J G, CARVALHO J A, SILVA M G. Experimental investigation of polyethylene combustion in a solid fuel ramjet: AIAA-1996-2698[R]. Reston: AIAA, 1996.
[4] ZVULONI R, LEVY Y, GANY A. Investigation of a small solid fuel ramjet combustor [J]. Journal of Propulsion and Power, 1989, 5(3): 269-275.
[5] 郭健. 固体燃料冲压发动机工作过程理论与试验研究[D]. 长沙: 国防科学技术大学, 2007: 42-70. GUO J. Theoretical and experimental investigation on the working process of solid fuel ramjet[D]. Changsha: National University of Defense Technology, 2007: 42-70 (in Chinese).
[6] 夏强. 固体燃料冲压发动机工作过程研究[D]. 南京: 南京理工大学, 2011: 82-112. XIA Q. Investigation on the working process of solid fuel ramjet[D]. Nanjing: Nanjing University of Science and Technology, 2011: 82-112 (in Chinese).
[7] 成红刚. 固体燃料冲压发动机燃烧性能数值仿真及试验研究[D]. 南京: 南京理工大学, 2013: 38-110. CHENG H G. Numerical simulation and experimental research on combustion characteristics of solid fuel ramjet[D]. Nanjing: Nanjing University of Science and Technology, 2013: 38-110 (in Chinese).
[8] 谢爱元, 武晓松. 外侧面燃烧固体燃料冲压发动机燃烧室流场的数值研究[J]. 推进技术, 2014, 35(7): 956-964. XIE A Y, WU X S. Numerical simulation on flow field of solid fuel ramjet combustion chamber with outboard burning[J]. Journal of Propulsion Technology, 2014, 35 (7):956-964 (in Chinese).
[9] 巩伦昆, 陈雄, 周长省, 等. 结构尺寸对固体燃料冲压发动机燃速影响的仿真研究[J]. 兵工学报, 2016, 37(5): 798-807. GONG L K, CHEN X, ZHOU C S, et al. Numerical investigation on the effect of solid fuel ramjet geometry on solid fuel regression rate[J]. Acta Armamentarii, 2016, 37(5): 798-807 (in Chinese).
[10] 巩伦昆, 陈雄, 周长省, 等. 来流条件对SFRJ燃速及自持燃烧性能的影响[J]. 航空学报, 2016, 37(5): 1428-1439. GONG L K, CHEN X, ZHOU C S, et al. Effect of inlet flow condition on regression rate and self-sustained combustion of solid fuel ramjet[J]. Acta Aeronautica et Astronautica Sinica, 2016, 37(5): 1428-1439 (in Chinese).
[11] SCHULTE G. Fuel regression and flame stabilization studies of solid-fuel ramjets[J]. Journal of Propulsion and Power, 1986, 2(4): 301-304.
[12] NETZER A, GANY A. Burning and flameholding characteristics of a miniature solid fuel ramjet combustor[J]. Propellants, Explosives, Pyrotechnics, 1991, 7(3): 357-363.
[13] ELANDS P, DIJSWIJK F, ZANDBERGEN B. Experimental and computational flammability limits in a solid fuel ramjet: AIAA-1990-1964[R]. Reston: AIAA, 1990.
[14] LIOU T M, LIEN W Y, HWANG P W. Flammability limits and probability density functions in simulated solid-fuel ramjet combustors[J]. Journal of Propulsion and Power, 1997, 13(5): 643-650.
[15] 朱国强. 固体燃料冲压发动机点火过程研究[D]. 南京: 南京理工大学, 2014: 79-111. ZHU G Q. The research on the ignition process of solid fuel ramjet[D]. Nanjing: Nanjing University of Science and Technology, 2014: 79-111 (in Chinese).
[16] STOLIAROV S I, WALTERS R N. Determination of the heats of gasification of polymers using differential scanning calorimetry[J]. Polymer Degradation and Stability, 2008, 93(2): 422-427.
[17] GASCOIN N, FAU G, GILLARD P. Flash pyrolysis of high density polyethylene: AIAA-2013-3833[R]. Reston: AIAA, 2013.
[18] BAURLE R A, MATHUR T, GRUBER M R, et al. A numerical and experimental investigation of a scramjet combustor for hypersonic missile applications: AIAA-1998-3521[R]. Reston: AIAA, 1998.
[19] ZHOU L X, CHEN X L, ZHENG C G, et al. Second-order moment turbulence-chemistry models for simulating NO_x formation in gas combustion[J]. Fuel, 2000, 79(11): 1289-1301.
[20] MATSUOKA T, MURAKAMI S, NAGATA H. Transition characteristics of combustion modes for flame spread in solid fuel tube[J]. Combustion and Flame, 2012, 159(7): 2466-2473.
[21] MAGNUSSENA B F, HJERTAGERA B H. On mathematical modeling of turbulent combustion with special emphasis on soot formation and combustion[J]. Symposium on Combustion, 1977, 16(1): 719-729.
[22] WILCOX D C. Dilatation-dissipation corrections for advanced turbulence models[J]. AIAA Journal, 1992, 30(11): 2639-2646.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

固体燃料冲压发动机自持燃烧的影响因素

Influencing factors for self-sustained combustion of solid fuel ramjet

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	林鹏, 庄福建, 曲林锋, 许阳阳, 苏亚东. 高超声速飞机尾喷管设计-制造与验证技术发展综述[J]. 航空学报, 2022, 43(6): 526160-526160.
[2]	李潮隆, 夏智勋, 马立坤, 赵翔, 罗振兵, 段一凡. 固体火箭超燃冲压发动机性能试验[J]. 航空学报, 2022, 43(12): 126075-126075.
[3]	王浩, 钟敏, 华俊, 钟海, 杨体浩, 王猛, 雷国东. 自然层流飞行测试翼套的仿真和试验[J]. 航空学报, 2022, 43(11): 526785-526785.
[4]	马光伟, 孙明波, 赵国焱, 李凡, 梁昌海, 陈慧锋. 不同壁温及差分格式下超燃冲压发动机的仿真[J]. 航空学报, 2021, 42(S1): 726353-726353.
[5]	左林玄, 张辰琳, 王霄, 卢恩巍, 朱伟. 高超声速飞机动力需求探讨[J]. 航空学报, 2021, 42(8): 525798-525798.
[6]	陈以勒, 俞凯凯, 徐惊雷. 几何尺寸约束的超燃冲压发动机推力喷管设计[J]. 航空学报, 2021, 42(6): 124259-124259.
[7]	郭鑫鑫, 陈哲涵. 激光增材制造过程数值仿真技术综述[J]. 航空学报, 2021, 42(10): 524227-524227.
[8]	郑忠华, 范周琴, 王子昂, 余彬, 张斌. 流场可压缩性对涡相互作用影响的数值研究[J]. 航空学报, 2020, 41(2): 123295-123295.
[9]	孟宇, 顾洪斌, 孙文明, 张新宇. 微波增强滑移电弧等离子体辅助超声速燃烧[J]. 航空学报, 2020, 41(2): 123345-123345.
[10]	陈文武, 黄利亚, 夏智勋, 李鹏飞. 跨介质冲压发动机理论性能与工作参数分析[J]. 航空学报, 2020, 41(11): 123764-123764.
[11]	孙维国, 史瑞华, 林左鸣, 刘代军, 张文山, 曹军伟, 范中国, 马聪慧, 付泽川, 刘爱华, 田鹏, 钱勤建, 陈飞, 段磊, 崔金平, 梁晓嘉. 基于固液相变燃料的冲压发动机[J]. 航空学报, 2019, 40(5): 122780-122780.
[12]	孟宇, 顾洪斌, 张新宇. 微波对超声速燃烧火焰结构的影响[J]. 航空学报, 2019, 40(12): 123224-123224.
[13]	王计真, 刘小川. 鸟撞平板试验与鸟体本构参数识别方法[J]. 航空学报, 2017, 38(S1): 721550-721550.
[14]	贺旭照, 乐嘉陵. 曲外锥乘波体进气道实用构型设计和性能分析[J]. 航空学报, 2017, 38(6): 120690-120690.
[15]	陈跃良, 王哲夫, 卞贵学, 王晨光, 张勇. 不同浓度NaCl溶液下典型铝/钛合金电偶腐蚀当量折算关系[J]. 航空学报, 2017, 38(3): 420450-420450.