间隙变化对压气机静叶叶栅气动性能的影响

doi:10.7527/S1000-6893.2016.0066

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

间隙变化对压气机静叶叶栅气动性能的影响

王子楠^1,2, 耿少娟², 张宏武²

1. 中国科学院大学, 北京 100190;
2. 中国科学院工程热物理研究所, 北京 100190

收稿日期:2015-12-09 修回日期:2016-03-07 出版日期:2016-11-15 发布日期:2016-03-14
通讯作者: 张宏武,男,博士,研究员,博士生导师。主要研究方向:叶轮机械气动热力学。Tel.:010-82543075,E-mail:zhw@iet.cn E-mail:zhw@iet.cn
作者简介:王子楠,男,博士研究生。主要研究方向:叶轮机械气动热力学。Tel.:010-82543134,E-mail:wangzinan@iet.cn;耿少娟,女,博士,副研究员。主要研究方向:叶轮机械气动力学。Tel.:010-82543094,E-mail:gengsj@iet.cn;张宏武,男,博士,研究员,博士生导师。主要研究方向:叶轮机械气动热力学。Tel.:010-82543075,E-mail:zhw@iet.cn
基金资助:
国家自然科学基金（50906080）

Influence of clearance variation on aerodynamic performance of a compressor stator cascade

WANG Zinan^1,2, GENG Shaojuan², ZHANG Hongwu²

1. University of Chinese Academy of Sciences, Beijing 100190, China;
2. Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China

Received:2015-12-09 Revised:2016-03-07 Online:2016-11-15 Published:2016-03-14
Supported by:
National Natural Science Foundation of China (50906080)

摘要/Abstract

摘要：

利用压气机平面叶栅试验，在大负攻角工况、设计工况和角区失速工况下，研究间隙变化对叶栅气动性能的影响，并分析内部流动变化与气动性能变化的关联。试验结果表明，不同工况下间隙变化对流场结构的影响不同，因而对叶栅性能的影响规律也不同。大负攻角工况下，不同间隙叶栅内在压力面前缘附近都存在一对由端壁向叶展中部发展的分离涡，间隙增大可以使叶栅总损失近似线性减小，并使间隙侧气流折转能力略微提升。设计工况下，无间隙侧吸力面角区存在轻微的角区分离，小间隙（0.2%展长）的引入首先会加剧间隙侧角区分离，当间隙进一步增大时，角区分离消失并形成泄漏涡结构。叶栅总损失随间隙增大呈先增大后减小再增加的趋势，角区分离的消除有助于提高间隙侧气流折转能力。角区失速工况下，间隙的引入可以削弱并移除间隙侧角区失速结构，从而使叶栅总损失下降，并在0.5%展长间隙时达到最小值，同时间隙侧气流折转能力得到增强。当间隙进一步增大时，叶栅损失变化不大。在间隙变化过程中，两侧端部流动结构产生相互影响，使两侧流场性能变化呈相反趋势。通过对比全工况范围内的气动性能，叶栅在选取0.5%展长间隙时整体性能最优。

关键词: 压气机, 平面叶栅, 静叶, 气动性能, 非设计工况, 泄漏流

Abstract:

In this paper, a linear compressor cascade is used to experimentally investigate the influence of clearance variation on the flow structures and cascade aerodynamic performance at the highly negative angle of attack, design condition and corner stall condition. The association between the flow structure and cascade performance is also analyzed. The experimental results show that the influence of clearance variation on flow structures and cascade performance is different at different working conditions. At highly negative angle of attack, a pair of three-dimensional separation vortexes near the pressure-side leading edge is originated from the end wall in different clearance cascades. With the increase of clearance size, the cascade total pressure loss decreases, and the clearance side cascade turning ability is slightly increased. At design condition, a slight corner separation exists between blade suction surface and end wall. By bringing in a small clearance (0.2% span), corner separation is first aggravated. As the clearance size continues to increase, the corner separation can be eliminated, and leakage vortex is formed. With the increase of clearance size, the cascade total pressure loss first increases, then decreases and finally goes up again. The elimination of corner separation will improve clearance side cascade flow turning ability. At corner stall condition, the introduction and increase of clearance can impair and eliminate the corner stall structure, and thus the cascade loss decreases and reaches the minimum value with a 0.5% span clearance size. But the cascade loss almost remains the same as clearance continues to increase. Flow structures at both enwalls can influence each other as clearance varies, and the change trends of performance near two end walls are opposite. By comparing the overall cascade aerodynamic performance at all working conditions, the 0.5% span clearance cascade shows an optimal performance.

Key words: compressor, linear cascade, stator, aerodynamic performance, off-design condition, leakage flow

中图分类号:

V211.7

王子楠, 耿少娟, 张宏武. 间隙变化对压气机静叶叶栅气动性能的影响[J]. 航空学报, 2016, 37(11): 3304-3316.

WANG Zinan, GENG Shaojuan, ZHANG Hongwu. Influence of clearance variation on aerodynamic performance of a compressor stator cascade[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2016, 37(11): 3304-3316.

参考文献

[1] 蒋洪德, 任静, 李雪英, 等. 重型燃气轮机现状与发展趋势[J]. 中国电机工程学报, 2014, 34(29):5096-5102. JIANG H D, REN J, LI X Y, et al. Status and development trend of the heavy duty gas turbine[J]. Proceedings of the CSEE, 2014, 34(29):5096-5102(in Chinese).
[2] 刘永泉, 刘太秋, 季路成. 航空发动机风扇/压气机技术发展的若干问题与思考[J]. 航空学报, 2015, 36(8):2563-2576. LIU Y Q, LIU T Q, JI L C. Some problem and thoughts in the development of aero-engine fan/compressor[J]. Acta Aeronautica et Astronautica Sinica, 2015, 36(8):2563-2576(in Chinese).
[3] FREEMAN C. Effect of tip clearance flow on compressor stability and engine performance:VKILS-1985-05[R]. Brussels:VKILS, 1985.
[4] SWOBODA M, IVEY P C, WENGER U, et al. An experimental examination of cantilevered and shrouded stators in a multistage axial compressor:ASME-98-GT-282[R]. New York:ASME, 1998.
[5] CAMPOBASSO M S, MATTHESIS A, WENGER U, et al. Complementary use of CFD and experimental measurements to assess the impact of shrouded and cantilevered stators in axial compressors:ASME-GT-208[R]. New York:ASME, 1999.
[6] 蔡睿贤, 王锡刚, 彭惠君, 等. 静叶内围带对轴流式压气机气动性能的影响及4500马力机车燃气轮机的热力性能[J]. 工程热物理学报, 1980, 1(1):3-9. CAI R X, WANG X G, PENG H J, et al. Influence of stator shroud on aerodynamic performance of axial-flow compressor and thermodynamic test results of a 4500 HP locomotive gas turbine[J]. Journal of Engineering Thermophysics, 1980, 1(1):3-9(in Chinese).
[7] LANGE M, MAILACH R, VOGELER K. An experimental investigation of shrouded and cantilevered stators at varying clearance sizes:ASME-GT2010-22106[R]. New York:ASME, 2010.
[8] DONG Y, GALLIMORE S J, HODSON H P. Three dimensional flows and loss reduction in axial compressors[J]. Journal of Turbomachinery, 1987, 109(3):354-361.
[9] YOON S, SELMEIER R, CARGILL P, et al. Effect of the stator hub configuration and stage design parameters on aerodynamic loss in axial compressors[J]. Journal of Turbomachinery, 2015, 137(9):091001-1-091001-10.
[10] KEY N. PIV Study of negative incidence stator unsteady aerodynamics:AIAA-2002-0014[R]. Reston:AIAA, 2002.
[11] HOWARD J. Sub-idle modelling of gas turbines:altitude relight and windmilling[D]. Bedfordshire:Cranfield University, 2007:23-30.
[12] ZACHOS P K, GRECH N, CHARNLEY B, et al. Experimental and numerical investigation of a compressor cascade at highly negative incidence[J]. Engineering Applications of Computational Fluid Mechanics, 2011, 5(1):26-36.
[13] HORLOCK J H, LOUIS J F, PERCIVAL P M E, et al. Wall stall in compressor cascades[J]. Journal of Basic Engineering, 1966, 88(3):637-648.
[14] LEI V M, SPAKOVSZKY Z S, GREITZER E M. A criterion for axial compressor hub-corner stall[J]. Journal of Turbomachinery, 2008, 130(3):031006-1-031006-10.
[15] MCDOUGAL N M. A comparison between the design point and near-stall performance of an axial compressor[J]. Journal of Turbomachinery, 1990, 112(1):109-115.
[16] 王子楠, 高磊, 耿少娟, 等. 不同端壁间隙下压气机平面叶栅角区流动的数值模拟和试验研究[J]. 工程热物理学报, 2015, 36(7):1428-1432. WANG Z N, GAO L, GENG S J, et al. Numerical and experimental investigation on corner flow structure in a planar compressor cascade with different clearances[J]. Journal of Engineering Thermophysics, 2015, 36(7):1428-1432(in Chinese).

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

间隙变化对压气机静叶叶栅气动性能的影响

Influence of clearance variation on aerodynamic performance of a compressor stator cascade

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张卫国, 唐敏, 武杰, 彭先敏, 章贵川, 聂博文, 王亮权, 李超群. 倾转旋翼机风洞试验综述[J]. 航空学报, 2024, 45(9): 530114-530114.
[2]	农历, 盛子帅, 冼军, 张怀宝. 基于高精度算法的结冰翼型分离流动数值模拟[J]. 航空学报, 2023, 44(S2): 729291-729291.
[3]	刘德龙, 郭海宁, 尹海宝, 孟德君. 单级跨音压气机第1级可调静子在退喘过程中的气动力矩分析[J]. 航空学报, 2023, 44(24): 128550-128550.
[4]	张健, 张敏, 杜娟, 黄伟亮, 聂超群. 自适应康达喷气控制在高负荷压气机中的试验研究[J]. 航空学报, 2023, 44(22): 128883-128883.
[5]	刘汝兵, 陈泽帆, 林瑞鑫, 林麒. 等离子体合成射流主动控制平面叶栅叶片流致振动[J]. 航空学报, 2023, 44(20): 128430-128430.
[6]	董杰忠, 楚武利, 张皓光, 罗波, 晏松. 基于因果网络分析的扩压叶栅波浪形前缘控制机理[J]. 航空学报, 2023, 44(19): 128336-128336.
[7]	汪松柏, 陈勇, 吴亚东, 张少平, 曹志鹏. 轴流压气机转子叶片非同步振动研究进展[J]. 航空学报, 2023, 44(17): 28044-028044.
[8]	王浩浩, 高丽敏, 杨光, 吴宝海. 一种鲁棒的数据驱动不确定性量化方法及在压气机叶栅中的应用[J]. 航空学报, 2023, 44(17): 128169-128169.
[9]	刘锬韬, 李瑞宇, 高丽敏, 赵磊. 基于数据同化的试验数据驱动的叶栅流场预测[J]. 航空学报, 2023, 44(14): 628201-628201.
[10]	徐慎忍, 何晨, 孙大坤, 袁蔡嘉, 曹东明, 赵家资, 王丁喜. 基于高效特征值分析方法的旋转失速先兆预测[J]. 航空学报, 2023, 44(14): 628248-628248.
[11]	许志远, 杨明绥, 王萌. 压气机声共振特性理论预测与试验研究[J]. 航空学报, 2023, 44(14): 628236-628236.
[12]	李秋琳, 周莉, 孙鹏, 史经纬, 王占学. 出口宽高比对S弯喷管流固耦合特性影响[J]. 航空学报, 2023, 44(14): 628204-628204.
[13]	程荣辉, 余华蔚, 汪松柏, 杜林, 孙大坤, 孙晓峰. 多级压气机转子负荷系数对叶片非同步振动的影响[J]. 航空学报, 2023, 44(14): 628722-628722.
[14]	赵红亮, 张文强, 邱佳慧, 张敏, 杜娟, 聂超群. 总温畸变下跨声压气机失速过程非定常模拟[J]. 航空学报, 2023, 44(14): 628319-628319.
[15]	李会, 黄通, 苏欣荣, 袁新. 基于DDES模拟的叶顶泄漏流与尾迹非定常干涉机理[J]. 航空学报, 2023, 44(14): 628325-628325.