低Cu含量Al-Mg-Si-Cu合金的T78双级时效

doi:10.7527/S1000-6893.2018.21986

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

低Cu含量Al-Mg-Si-Cu合金的T78双级时效

王芝秀^1,2, 朱凡¹, 郑凯¹, 李海^1,2

1. 常州大学材料科学与工程学院, 常州 213164;
2. 江苏省材料表面科学与技术重点实验室, 常州 213164

收稿日期:2018-01-02 修回日期:2018-03-07 出版日期:2018-08-15 发布日期:2018-03-07
通讯作者: 李海 E-mail:lehigh_73@163.com
基金资助:
国家自然科学基金（51671038，51571038）；江苏省自然科学基金（BK20151188，BK20171195）

Two step ageing (T78 temper) of an Al-Mg-Si-Cu alloy with small Cu addition

WANG Zhixiu^1,2, ZHU Fan¹, ZHENG Kai¹, LI Hai^1,2

1. School of Materials Science and Engineering, Changzhou University, Changzhou 213164, China;
2. Jiangsu Key Laboratory of Materials Surface Science and Technology, Changzhou 213164, China

Received:2018-01-02 Revised:2018-03-07 Online:2018-08-15 Published:2018-03-07
Supported by:
National Natural Science Foundation of China (51671038, 51571038);Natural Science Foundation of Jiangsu Province (BK20151188, BK20171195)

摘要/Abstract

摘要： 采用拉伸和加速腐蚀试验，分别测试了预时效（180℃）+再时效（190、200、210℃）对一种低Cu含量Al-Mg-Si-Cu合金拉伸性能和晶间腐蚀的影响，结果表明，延长预时效和再时效时间或提高再时效温度，合金强度逐渐降低，同时，腐蚀类型按晶间腐蚀→均匀腐蚀→坑蚀顺序演化。其中，经预时效（180℃/2~8 h）+再时效（200℃/6 h或210℃/2 h）处理，合金抗拉强度、屈服强度和延伸率分别为380~395 MPa、360~380 MPa和12%~15%，腐蚀类型为均匀腐蚀，实现强度与耐蚀性的良好配合。透射电镜观察表明，随着双级时效程度的增加，合金强度的降低源于基体β"相的减少及β'相和Q'相的增加；晶间腐蚀倾向的降低与晶界Q相大间距、断续分布有关；坑蚀的形成则与结晶Q相吸收周围析出相、形成基体无析出区有关。

关键词: 铝合金, 时效, 析出相, 晶间腐蚀, 坑蚀

Abstract: The tensile properties and intergranular corrosion of an Al-Mg-Si-Cu alloy with small Cu addition during a two-step ageing (T78 temper) consisting of low-temperature pre-ageing at 180℃ and high-temperature re-ageing at 190, 200 and 210℃ Were investigated by the tensile and accelerated corrosion tests. The results show that with the increase of the pre-ageing and re-ageing time or re-ageing temperature, the strength of the alloy decreases gradually, and the corrosion mode changes in the sequence of intergranular corrosion, uniform corrosion and pitting corrosion. After pre-ageing at 180℃ for 2-8 h and re-ageing at 200℃ for 6 h or 210℃ for 2 h, the alloy has the ultimate tensile strength, yield strength and elongation to failure of 380-395 MPa, 360-380 MPa and 12%-15% respectively, accompanied by uniform corrosion. The transmission electron microscopy observations show that during two-step ageing, the decrease in strength of the alloy is attributed to the decrease of β" precipitates and the increase of β' and Q' precipitates, the decreased intergranular corrosion results from the enlarged interspacing between the grain boundary Q precipitates, andthe increased pitting corrosion is due to the precipitate free zones around the constituent Q phase as a result of coarsening.

Key words: aluminum alloy, ageing, precipitate, intergranular corrosion, pitting corrosion

中图分类号:

V252.2

王芝秀, 朱凡, 郑凯, 李海. 低Cu含量Al-Mg-Si-Cu合金的T78双级时效[J]. 航空学报, 2018, 39(8): 421986-421986.

WANG Zhixiu, ZHU Fan, ZHENG Kai, LI Hai. Two step ageing (T78 temper) of an Al-Mg-Si-Cu alloy with small Cu addition[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(8): 421986-421986.

参考文献

[1] MILLER W S, ZHUANG L, BOTTEMA J, et al. Recent development in aluminium alloys for the automotive industry[J]. Materials Science Engineering A, 2000, 280(1):37-49.
[2] HEINZ A, HASZLER A, KEIDEL C, et al. Recent development in aluminium alloys for aerospace applications[J]. Materials Science Engineering A, 2000, 280(1):102-107.
[3] 贺春林, 孟小丹, 马国峰, 等. 6000系铝合金晶间腐蚀研究进展[J]. 沈阳大学学报(自然科学版), 2014, 26(1):18-23. HE C L, MENG X D, MA G F, et al. Research development in intergranular corrosion of 6000(series aluminum alloys[J]. Journal of Shenyang University (Natural Science), 2014, 26(1):18-23(in Chinese).
[4] 王芝秀, 李海, 顾建华, 等. Cu含量对Al-Mg-Si-Cu合金微观组织和性能的影响[J]. 中国有色金属学报, 2012, 22(12):3348-3355. WANG Z X, LI H, GU J H, et al. Effect of Cu content on microstructures and properties of Al-Mg-Si-Cu alloys[J]. The Chinese Journal of Nonferrous Metals, 2012, 22(12):3348-3355(in Chinese).
[5] ZOU Y, LIU Q, JIA Z H, et al. The intergranular corrosion behavior of 6000-series alloys with different Mg/Si and Cu content[J]. Applied Surface Science, 2017, 405:489-496.
[6] KAIRY S K, ROMETSCH P A, DIAO K, et al. Exploring the electrochemistry of 6xxx series aluminium alloys as a function of Si to Mg ratio, Cu content, ageing conditions and microstructure[J]. Electrochimica Acta, 2016, 190:92-103.
[7] LIANG W J, ROMETSCH P A, CAO L F, et al. General aspects related to the corrosion of 6xxx series aluminium alloys:Exploring the influence of Mg/Si ratio and Cu[J]. Corrosion Science, 2013, 76(10):119-128.
[8] KAIRY S K, ALAM T, ROMETSCH P A, et al. Understanding the origins of intergranular corrosion in copper containing Al-Mg-Si alloys[J]. Metallurgical Materials Transaction A, 2016, 47(3):985-989.
[9] DIF R, BES B, EHRSTRO M, et al. Understanding and modeling the mechanical and corrosion properties of 6056 for aerospace applications[J]. Materials Science Forum, 2000, 331-337:1613-1618.
[10] 潘道召, 王芝秀, 李海, 等. 双级时效对6061铝合金拉伸性能和晶间腐蚀性能的影响[J]. 中国有色金属学报, 2010, 20(3):435-441. PAN D Z, WANG Z X, LI H, et al. Effects of two(step ageing treatment on tensile properties and intergranular corrosion of 6061 aluminum alloy[J]. The Chinese Journal of Nonferrous Metals, 2010, 20(3):435-441(in Chinese).
[11] 张海锋, 郑子樵, 钟申, 等. 双级时效制度对6156铝合金组织和性能的影响[J]. 中国有色金属学报, 2012, 22(4):1025-1032. ZHANG H F, ZHENG Z Q, ZHONG S, et al. Effects of two-step aging treatment on microstructure and properties of 6156 aluminum alloy[J]. The Chinese Journal of Nonferrous Metals, 2012, 22(4):1025-1032(in Chinese).
[12] 林莉, 郑子樵, 李劲风. 时效制度对6156铝合金力学性能及腐蚀性能的影响[J]. 稀有金属材料与工程, 2012, 41(6):1004-1009. LIN L, ZHENG Z Q, LI J F. Effect of aging treatments on the mechanical properties and corrosion behavior of 6156 aluminum alloy[J]. Rare Metal Materials and Engineering, 2012, 41(6):1004-1009(in Chinese).
[13] 李海, 毛庆忠, 王芝秀, 等. 高温预时效+低温再时效对Al-Mg-Si-Cu合金力学性能及晶间腐蚀敏感性的影响[J]. 金属学报, 2014(11):1357-1366. LI H, MAO Q Z, WANG Z X, et al. Effect of high temperature pre-ageing and low-temperature re-ageing on mechanical properties and intergranular corrosion susceptibility of Al-Mg-Si-Cu alloys[J]. Acta Metallurgica Sinica, 2014(11):1357-1366(in Chinese).
[14] 王胜强, 陆政, 戴圣龙, 等. 6A60铝合金板材三级时效工艺研究[J]. 航空材料学报, 2003, 23(s1):78-82. WANG S Q, LU Z, DAI S L, et al. Study on the three-step aging of 6A60 aluminium alloy sheet[J]. Journal of Aeronautical Materials, 2003, 23(s1):78-82(in Chinese).
[15] ASSERIN-LEBERT A, BESSON J, GOURGUES A F. Fracture of 6056 aluminum sheet materials:Effect of specimen thickness and hardening behavior on strain localization and toughness[J]. Materials Science and Engineering A, 2005,395(1-2):186-194.
[16] KAIRY S K, ALAM T, ROMETSCH P A, et al. Understanding the origins of intergranular corrosion in copper containing Al-Mg-Si alloys[J]. Metallurgical Materials Transaction A, 2016, 47(3):985-989.
[17] KAIRY S K, ROMETSCH P A, DAVIES C H J, et al. On the intergranular corrosion and hardness evolution of 6xxx series Al alloys as a function of Si:Mg ratio, Cu content and ageing condition[J]. Corrosion, 2017, 73(10):1280-1295.
[18] 陈江华, 刘春辉. AlMgSi(Cu)合金中纳米析出相的结构演变[J]. 中国有色金属学报, 2011, 21(10):2352-2360. CHEN J H, LIU C H. Microstructure evolution of precipitates in AlMgSi(Cu) alloys[J]. The Chinese Journal of Nonferrous Metals, 2011, 21(10):2352-2360(in Chinese).
[19] 李祥亮, 陈江华, 刘春辉, 等. T6和T78时效工艺对Al-Mg-Si-Cu合金显微结构和性能的影响[J]. 金属学报, 2013, 49(2):243-250. LI X L, CHEN J H, LIU C H, et al. Effects of T6 and T78 tempers on the microstructures and properties of Al-Mg-Si-Cu alloys[J]. Acta Metallurgica Sinica, 2013, 49(2):243-250(in Chinese).
[20] 廖元飞, 陈江华, 刘春辉, 等. Al-Mg-Si-Cu合金中晶界和晶内析出相粗化规律的研究[J]. 电子显微学报, 2012, 31(2):116-123. LIAO Y F, CHEN J H, LIU C H, et al. An electron microscopy study of precipitate coarsening in Al-Mg-Si-Cu alloys[J]. Journal of Chinese Electron Microscopy Society, 2012, 31(2):116-123(in Chinese).
[21] BISWAS A, SIEGEL D J, SEIDMAN D N. Compositional evolution of Q-phase precipitates in an aluminum alloy[J]. Acta Materials, 2014, 75(9):322-336.
[22] BUHA J, LUMLEY R N, CROSKY A G, et al. Secondary precipitation in an Al-Mg-Si-Cu alloy[J]. Acta Materialia, 2007, 55(9):3015-3024.
[23] CHAKRABARTI D J, LAUGHLIN D E. Phase relations and precipitation in Al-Mg-Si alloys with Cu additions[J]. Progress in Materials Science, 2004, 49(3-4):389-410.
[24] 李海, 孟林, 王芝秀, 等. 残留结晶相对Al-Mg-Si-Cu合金晶间腐蚀行为的影响[J]. 中国有色金属学报, 2012, 22(12):3300-3306. LI H, MENG L, WANG Z X, et al. Effect of residual constituents on intergranular corrosion behavior of Al-Mg-Si-Cu alloy[J]. The Chinese Journal of Nonferrous Metals, 2012, 22(12):3300-3306(in Chinese).
[25] 徐丽新, 胡津, 耿林, 等. 铝的点蚀行为[J]. 宇航材料工艺, 2002, 32(2):21-24. XU L X, HU J, GENG L, et al. Pitting behavior of aluminum[J]. Aerospace Materials & Technology, 2002, 32(2):21-24(in Chinese).

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

低Cu含量Al-Mg-Si-Cu合金的T78双级时效

Two step ageing (T78 temper) of an Al-Mg-Si-Cu alloy with small Cu addition

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	高同州, 贺小帆, 王晓雷, 李紫光, 朱振涛, 詹志新. 基于CDM理论与SVM模型的2014-T6铝合金疲劳寿命预测[J]. 航空学报, 2024, 45(7): 228952-228952.
[2]	应岳峰, 陈琪昊, 王卫东, 毛欣宇. 焊丝超声振动对铝合金熔化极气体保护焊缝成形及气孔的影响[J]. 航空学报, 2024, 45(2): 428711-428711.
[3]	唐论, 余圣甫, 郑博, 史玉升, 陈颖. 圆柱面点阵自生Al₂O₃铝合金粉芯丝材开发及应用[J]. 航空学报, 2023, 44(9): 626864-626864.
[4]	林忠钦, 于忠奇, 戴冬华, 樊晓光, 余圣甫, 顾冬冬, 李淑慧, 史玉升. 复杂高筋薄壁构件旋压-增材复合制造技术发展与展望[J]. 航空学报, 2023, 44(9): 627493-627493.
[5]	金士杰, 王志诚, 田鑫, 孙旭, 林莉. 基于半跨模式波的铝合金板底面缺陷TOFD检测[J]. 航空学报, 2023, 44(4): 426674-426674.
[6]	邹田春, 巨乐章, 管玉玺, 李泽钢, 陈红呈. 铺层方式对CFRP⁃Al胶接接头疲劳行为的影响[J]. 航空学报, 2023, 44(18): 428264-428264.
[7]	何盼, 卢超, 石文泽, 朱颖, 陈果, 赵莉萍. 铝合金激光超声表面检测中EMAT接收性能对比[J]. 航空学报, 2023, 44(16): 428085-428085.
[8]	张志强, 勾青泽, 路学成, 王浩, 曹轶然, 郭志永. 高强铝合金CMT+P电弧增材制造熔滴过渡行为[J]. 航空学报, 2023, 44(13): 427881-427881.
[9]	张天刚, 黄嘉浩, 侯晓云, 张志强. 激光清洗铝合金表面复合漆层作用机制[J]. 航空学报, 2023, 44(11): 427656-427656.
[10]	石文泽, 程进杰, 胡硕臻, 卢超, 陈尧. 脉冲压缩在铝薄板电磁超声导波检测中的应用[J]. 航空学报, 2022, 43(3): 425063-425063.
[11]	杨炳鑫, 马运五, 山河, 杨天豪, 孙靖, 李永兵. 2A12-T4铝合金自冲摩擦铆焊接头力学行为研究[J]. 航空学报, 2022, 43(2): 625111-625111.
[12]	李洪亮, 崔展祥, 刘世雄, 马强, 姚亦强, 雷玉成. 6061铝合金超声电弧MIG焊声电特性和工艺[J]. 航空学报, 2022, 43(2): 624969-624969.
[13]	姜春阳, 吴利辉, 常云龙, 薛鹏, 倪丁瑞, 肖伯律, 马宗义. 铝合金与树脂基复合材料的铆接/搅拌摩擦搭接复合焊接[J]. 航空学报, 2022, 43(2): 625190-625190.
[14]	徐孟嘉, 刘博生, 毕晓阳, 王振民. 激光加工双级结构对Al/CFRPEEK接头组织及性能的影响[J]. 航空学报, 2022, 43(2): 624620-624620.
[15]	刘浩, 陈玉华, 章文滔. Ti/Al无针搅拌摩擦搭接点焊接头组织特征[J]. 航空学报, 2022, 43(2): 624680-624680.