首页 >

CFRP气雾中电火花加工实验研究

韩家璇,陈璠,杨旭光,王振宇,岳晓明   

  1. 山东大学
  • 收稿日期:2024-07-01 修回日期:2024-10-08 出版日期:2024-10-11 发布日期:2024-10-11
  • 通讯作者: 岳晓明
  • 基金资助:
    国家自然科学基金资助项目;山东省自然科学基金

Experimental Study on EDM of CFRP in Aerosol Medium

  • Received:2024-07-01 Revised:2024-10-08 Online:2024-10-11 Published:2024-10-11

摘要: 碳纤维增强树脂基复合材料(CFRP)作为一种先进复合材料被广泛应用。传统切削加工方法加工CFRP易形成分层、毛刺、裂纹等加工缺陷,且对刀具有较大磨损。而激光加工和水射流加工CFRP易产生热影响区、冲击破坏、阶梯状分层等加工缺陷。作为一种非接触式加工方法,电火花加工(EDM)可以加工任何导电材料,而与工件的强度、硬度以及刚度无关,因此,电火花加工在解决大型CFRP构件难加工方面具有较大的应用潜力。但电火花加工CFRP存在CFRP工件被液态加工介质污染以及CFRP工件尺寸受限等难题。为此,本文提出在气雾介质中进行CFRP电火花加工,并搭建了基于六自由度串联机器人的电火花加工装置。开展了CFRP复合材料的电火花铣削加工实验,揭示了CFRP材料气雾中电火花加工的雾滴作用机理,验证了CFRP气雾中电火花加工的可行性。本研究对于大型复杂CFRP薄壁结构件的低成本绿色高效加工具有重要意义。

关键词: 碳纤维增强树脂基复合材料, 气雾介质, 电火花加工, 雾滴作用, 热损伤区域

Abstract: Carbon fiber reinforced polymer (CFRP) are widely used as an advanced composite material. Traditional cutting methods for processing CFRP are prone to forming machining defects such as delamination, burrs, and cracks, and have the problem of severe tool wear. Laser processing and water jet processing of CFRP are prone to generating the processing defects such as the heat affected zones, impact damage, and stepped delamination. As a non-contact machining method, electrical discharge machining (EDM) can machine any conductive material regardless of the strength, hardness, and stiffness of the workpiece material. Therefore, EDM has a great potential in solving the difficult machining problem of large CFRP components. However, the EDM of CFRP faces challenges such as the contamination of the CFRP compo-nents by the liquid medium and the limited size of the CFRP components. Therefore, this study proposes to perform the CFRP EDM in an aerosol medium and builds an EDM milling machine tool based on a six degree of freedom serial robot. The experiments on planar and spatial EDM milling of the CFRP components were conducted and the action mechanism of the droplet in EDM of CFRP material in aerosol medium was revealed, verifying the feasibility of the EDM milling of CFRP in aerosol medium. This study has a great significance for the low-cost, green, and efficient process of large and complex CFRP thin-walled structural components.

Key words: Carbon Fiber Reinforced Polymer (CFRP), Aerosol Medium, Electrical Discharge Machining (EDM), Droplet action, Heat damage area

中图分类号: