过冷水滴凝固机理及凝固组织特征

doi:10.7527/S1000-6893.2018.22627

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

过冷水滴凝固机理及凝固组织特征

杜雁霞, 肖光明, 张楠, 李伟斌, 王梓旭, 易贤, 桂业伟

中国空气动力研究与发展中心空气动力学国家重点实验室, 绵阳 621000

收稿日期:2018-08-25 修回日期:2018-09-25 出版日期:2019-07-15 发布日期:2018-11-09
通讯作者: 杜雁霞 E-mail:yanxiadu@163.com
基金资助:
国家自然科学基金（11672322，11472295）；国家重点基础研究发展计划（2015CB755800）

Freezing mechanism and microstructure characteristics in solidification of supercooled water droplets

DU Yanxia, XIAO Guangming, ZHANG Nan, LI Weibin, WANG Zixu, YI Xian, GUI Yewei

State Key Laboratory of Aerodynamics, China Aerodynamics Research and Development Center, Mianyang 621000, China

Received:2018-08-25 Revised:2018-09-25 Online:2019-07-15 Published:2018-11-09
Supported by:
National Natural Science Foundation of China (11672322,11472295); National Key Basic Research Program of China (2015CB755800)

摘要/Abstract

摘要： 针对飞机过冷水滴结冰的精细化预测需求，基于相变热力学与相变动力学相关理论，采用示差扫描量热法（DSC）、结冰风洞试验及微结构测试相结合的方法，研究了过冷水滴凝固过程的热力学机理及凝固组织特征。基于示差扫描量热法，研究了冷却速率及形核条件对结晶凝固特性的影响规律；基于结冰风洞试验开展了不同温度条件下冰相的宏观形貌及微结构特征研究。结果表明，过冷条件及冷却速率是影响过冷水滴结晶速率及结晶完善程度的重要因素。降温速率越大，结晶速率常数增大、结晶速率相应提高。同时，结晶峰变宽，结晶初始温度向低温方向移动，过冷效应相对显著；反之亦然。过冷度及冷却速率对冰相的宏观及微观形貌均有着重要影响。过冷度越大则相同时间内冷却速率越大，晶体生长过程越不充分，晶体不规则程度相对较高，同时晶粒密度变大、尺度变小，冰相表观透明度相对降低；反之，过冷度越小，则晶粒密度变小、尺度变大，冰相表观透明度相对较高。异相形核条件对加速结晶过程有重要促进作用，晶种的存在可有效加速二次结晶的触发，使过冷效应显著减弱。相关研究可为飞机结冰速率、冰相物理特征及冰形宏观形貌的精细化预测提供参考。

关键词: 过冷水滴, 凝固, 热力学特性, 微结构, 二次结晶

Abstract: To better meet the demand of refined prediction of the aircraft icing process, the freezing mechanisms and microstructure characteristics in solidification of supercooled water droplets are studied combining the theory of phase-change thermodynamics and kinetics with tests. Based on the Differential Scanning Calorimetry (DSC) test, the effects of cooling rate and nucleation conditions on the solidification characteristics are studied. Icing tunnel tests are carried out at different temperature conditions, and the macroscopic morphology and microstructure characteristics of ice are obtained. The results indicate that icing conditions and cooling rate have great influence on the crystallization behavior of supercooled water. The greater the cooling rate, the greater the crystallization rate. At the same time, the crystallization peak becomes wider, and the initial temperature of crystallization becomes lower, and vice versa. The subcooling and cooling rate have important influence on the macroscopic and microscopic morphology of ice. The greater the subcooling and cooling rate, the more irregular the grains, the larger density and the smaller the grains, and the ice phase looks more opaque. On the contrary, the smaller the subcooling, the lower density and the larger the grains, and the ice phase looks more transparent. Heterogeneous nucleation conditions play an important role in accelerating the crystallization process. The addition of crystal seeds can trigger the crystallization effectively, significantly reducing the supercooling effect. The results lay an important foundation for better understanding the mechanisms of aircraft icing, which has important value for predicting the icing process more accurately.

Key words: supercooled water droplets, solidification, thermodynamics characteristics, microstructure, secondary crystallization

中图分类号:

V211.3

杜雁霞, 肖光明, 张楠, 李伟斌, 王梓旭, 易贤, 桂业伟. 过冷水滴凝固机理及凝固组织特征[J]. 航空学报, 2019, 40(7): 122627-122627.

DU Yanxia, XIAO Guangming, ZHANG Nan, LI Weibin, WANG Zixu, YI Xian, GUI Yewei. Freezing mechanism and microstructure characteristics in solidification of supercooled water droplets[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(7): 122627-122627.

参考文献

[1] SANG W, JIANG S, LI F. Icing research for airfoil and multi-element airfoil:AIAA-2006-3647[R]. Reston, VA:AIAA, 2006.
[2] National Transportation Safety Board. Aviation accident statistics[R]. Washington, D.C.:National Transportation Safety Board, 2008.
[3] ROISMAN I V. Fast forced liquid film spreading on a substrate:Flow, heat transfer and phase transition[J]. Journal of Fluid Mechanics, 2010, 656:189-204.
[4] BLAKE J, THOMPSON D, RAPS D, et al. Simulating the freezing of supercooled water droplets impacting a cooled substrate[J]. AIAA Journal, 2015, 53(7):1725-1739.
[5] 徐祖耀. 相变原理[M]. 北京:科学出版社, 1988:123-124. XU Z Y. Principles of phase transformations[M]. Beijing:Science Press, 1988:123-124(in Chinese).
[6] SHIBKOV A A, GOLOVIN Y I, ZHELTOV M A, et al. Morphology diagram of non-equilibrium patterns of ice crystals growing in supercooled water[J]. Physica A:Statistical Mechanics and Its Applications, 2003, 319:65-79.
[7] KING W D. Freezing rates of water droplets[J]. Journal of the Atmospheric Sciences, 1975, 32(2):403-408.
[8] TABAKOVA S, FEUILLEBOIS F, RADEV S. Freezing of a suspended supercooled droplet with a heat transfer mixed condition on its outer surface[C]//1st International Conference on Applications of Mathematics in Technical and Natural Sciences. New York:AIP Publishing, 2009:240-247.
[9] GENNES P G D. Wetting:Static and dynamics[J]. Review of Modern Physics, 1985, 57(3):827-863.
[10] CAMPOS A L, SILVA N T, MELO F C L, et al. Crystallization kinetics of orthorhombic mullite from diphasic gels[J]. Journal of Non-Crystalline Solids, 2002, 304(1):19-24.
[11] IQBAL N, VAN DIJK N H, VERHOEVEN V W J, et al. Experimental study of ordering kinetics in aluminum alloys during solidification[J]. Acta Materialia, 2003, 51(25):4497-4504.
[12] DAVIS S H. Theory of solidication[M]. New York:Cambridge University Press, 2001:26-27.
[13] LYNCH M, GILL W N, ANANTH R. The growth of ice dendrites under mixed convection conditions[J]. Chemical Engineering Communications, 1987, 55:295-312.
[14] 曲凯阳, 江亿. 均质形核结冰随机性及形核率的研究[J].物理学报, 2000, 49(11):2214-2219. QU K Y, JIANG Y. Studies on randomness and nucleation rate of supercooled water freezing from homogeneous nucleation[J]. Acta Physica Sinica, 2000, 49(11):2214-2219(in Chinese).
[15] ELLEN N, JACCO M H, EDWIN W, et al. Aircraft icing in flight:Effects of impact of supercooled large droplets[C]//29th Congress of the International Council of the Aeronautical Sciences, 2004:1-17.
[16] LIU M, ZHAO Q, WANG Y, et al. Melting behaviors, isothermal and non-isothermal crystallization kinetics of nylon 1212[J].Polymer, 2003, 44(8):2537-2545.
[17] JEZIORNY A. Parameters characterizing the kinetics of the non-isothermal crystallization of poly (ethylene terephthalate) determined by DSC[J]. Polymer, 1978, 19(10):1142-1144.
[18] PURI S, WADHAWAN V. Kinetics of phase transitions[M]. Boca Raton, FL:CRC Press, 2009:8-68.
[19] 裘燮纲, 韩凤华. 飞机防冰系统[M]. 北京:航空专业教材编审室, 1985. QIU X G, HAN F H. Aircraft anti-icing system[M]. Beijing:Aviation Professional Textbook Editorial Office, 1985(in Chinese).
[20] 潘环, 艾剑良. 飞机结冰冰形预测的建模与仿真[J]. 系统仿真学报, 2014, 26(1):221-224. PAN H, AI J L. Modeling and simulation of aircraft ice shape prediction[J]. Journal of System Simulation, 2014, 26(1):221-224(in Chinese).
[21] LI Y, WANG S, SUN C, et al. Icing distribution of rotating blade of horizontal axis wind turbine based on quasi-3D numerical simulation[J]. Thermal Science, 2018, 22(S2):S681-S692.
[22] 黄起森, 刘礼, 韦修勋, 等. 过冷Ni-P合金的凝固行为[J].物理学报, 2012, 61(16):367-374. HUANG Q S, LIU L, WEI X X, et al. Solidification behavior of undercooling Ni-P alloy[J]. Acta Physica Sinica, 2012, 61(16):367-374(in Chinese).
[23] 杜雁霞, 李明, 桂业伟, 等. 飞机结冰热力学行为研究综述[J]. 航空学报, 2017, 38(2):520706. DU Y X, LI M, GUI Y W, et al. Review of thermodynamic behaviors in aircraft icing process[J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(2):520706(in Chinese).
[24] 李伟斌, 易贤, 杜雁霞, 等. 基于变分分割模型的结冰形测量方法[J]. 航空学报, 2017, 38(1):120167. LI W B, YI X, DU Y X, et al. A measurement approach for ice shape based on variational segmentation model[J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(1):120167(in Chinese).
[25] 桂业伟, 周志宏, 李颖晖, 等. 关于飞机结冰的多重安全边界问题[J]. 航空学报, 2017, 38(2):520723. GUI Y W, ZHOU Z H, LI Y H, et al. Multiple safety boundaries protection on aircraft icing[J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(2):520723(in Chinese).

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

过冷水滴凝固机理及凝固组织特征

Freezing mechanism and microstructure characteristics in solidification of supercooled water droplets

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	牛家宏, 贾浩楠, 易法军, 彭祖军, 陈伟. 致密非晶SiCN低压热稳定性及高温导电行为[J]. 航空学报, 2022, 43(S2): 152-159.
[2]	张佩宇, 周鑫, 李应红. 单晶涡轮叶片高能束修复研究进展[J]. 航空学报, 2022, 43(4): 525610-525610.
[3]	杨夏炜, 彭冲, 马铁军, 温国栋, 王艳莹, 柴小霞, 徐雅欣, 李文亚. 高温合金线性摩擦焊接头疲劳裂纹扩展有限元分析[J]. 航空学报, 2022, 43(2): 625004-625004.
[4]	崔静, 张杭, 翟巍, 路梦柯, 杨广峰. 飞秒脉冲激光诱导TC4微结构表面抑冰特性实验[J]. 航空学报, 2021, 42(6): 424032-424032.
[5]	李超群, 李易, 张晨曦, 唐硕. 沿流向微结构沟槽流场直接数值模拟[J]. 航空学报, 2020, 41(11): 123628-123628.
[6]	黄福享, 苗恺, 鲁中良, 徐文梁, 朱伟军, 李涤尘. 辐射涂层对空心涡轮叶片定向凝固组织的影响[J]. 航空学报, 2018, 39(3): 421462-421462.
[7]	王津, 杨辉, 王莉平, 董璞. 防冰疏水微结构表面的设计[J]. 航空学报, 2017, 38(S1): 721522-721522.
[8]	杜雁霞, 李明, 桂业伟, 王梓旭. 飞机结冰热力学行为研究综述[J]. 航空学报, 2017, 38(2): 520706-520717.
[9]	肖光明, 杜雁霞, 王桥, 郭龙, 王茂. 考虑非平衡效应的过冷水滴凝固特性[J]. 航空学报, 2017, 38(2): 520703-520709.
[10]	张琪, 孙璐璐, 逄淑杰, 张涛. 耐腐蚀Fe-Cr-Mo-C-B合金的激光表面非晶化及其对结构和性能的影响[J]. 航空学报, 2014, 35(10): 2881-2888.
[11]	张虎, 原赛男, 周春根, 沙江波, 赵新青, 贾丽娜. Nb-Si金属间化合物基超高温合金研究进展[J]. 航空学报, 2014, 35(10): 2756-2766.
[12]	王华明. 高性能大型金属构件激光增材制造：若干材料基础问题[J]. 航空学报, 2014, 35(10): 2690-2698.
[13]	杨晓光, 黄佳, 王井科, 胡晓安, 石多奇. 定向凝固镍基高温合金缺口低循环疲劳性能及寿命预测[J]. 航空学报, 2013, 34(7): 1596-1604.
[14]	于洽, 朱荻, 曾永彬, 张海. 微幅往复走丝微细电解线切割试验研究 [J]. 航空学报, 2012, (5): 920-927.
[15]	顾玉丽, 滕旭东, 刘昌奎, 何玉怀, 陶春虎. DZ125定向凝固高温合金长期时效后的显微组织和超高周疲劳行为[J]. 航空学报, 2012, 33(11): 2136-2142.