不锈钢增材制造件后处理工艺研究进展

doi:10.7527/S1000-6893.2021.25847

综述

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

不锈钢增材制造件后处理工艺研究进展

李汇¹, 李光先², 高瑞麟¹, 金鑫¹, 刘璐¹, 李朝将¹, Songlin DING²

1. 北京理工大学机械与车辆学院, 北京 100089;
2. 皇家墨尔本理工大学邦杜拉校区东区工程学院, 墨尔本 3082

收稿日期:2021-05-20 修回日期:2021-06-02 发布日期:2021-08-03
通讯作者: 李朝将 E-mail:mecjli@bit.edu.cn
基金资助:
国家重点研发计划（2018YFB1306300）；北京理工大学学术启动计划（2020CX04060）

Research progress of post-processing of stainless steel additive manufacturing parts

LI Hui¹, LI Guangxian², GAO Ruilin¹, JIN Xin¹, LIU Lu¹, LI Chaojiang¹, Songlin DING²

1. School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100089, China;
2. School of Engineering, Royal Melbourne Institute of Technology Bundoora East Campus, Mill Park 3082, Australia

Received:2021-05-20 Revised:2021-06-02 Published:2021-08-03
Supported by:
National Key Research and Development Program of China (2018YFB1306300); Academic Initiation Program of Beijing Institute of Technology (2020CX04060)

摘要/Abstract

摘要： 由于金属材料增材制造技术的逐层成形过程特点，增材制造件存在着一些难以避免的问题，如表面粗糙、残余应力较高及由于粉末熔融不完全引起的亚表面微裂纹及气孔等，无法直接进行装配应用。综述结合了近年来国内外不锈钢增材制造件后处理工艺的研究成果及不锈钢增材制造件的缺陷类型，分析了不同增材制造工艺的区别及用途，以及目前国内外对增材制造件工艺参数的优化进展，热处理、机械加工等后处理工艺的国内外研究现状，总结了不锈钢增材制造件后处理工艺的关键问题，探讨了不锈钢增材制造件后处理工艺发展趋势。

关键词: 增材制造, 不锈钢材料, 后处理工艺, 可加工性, 残余应力

Abstract: The parts fabricated by Additive Manufacturing (AM) cannot be used directly due to the defects caused by layer-by-layer formation of AM, including coarse surface, high residual stress, and pores/micro cracks beneath the surface caused by insufficient melting. The review summarizes the research results of the post-treatment processes of stainless steel additive manufacturing components at home and abroad and the defect types of stainless steel additive manufacturing components, analyzes the differences and uses of different additive manufacturing processes, and current domestic and international optimization progress of the process parameters of the additive manufacturing components, heat treatment, mechanical processing and other post-treatment processes, The key problems of post-treatment process of stainless steel additive manufacturing pieces are summarized, and the development trend of post-treatment process of stainless steel additive manufacturing pieces is discussed.

Key words: additive manufacturing, stainless steel material, post-processing technology, machinability, residual stress

中图分类号:

V261.2⁺1

李汇, 李光先, 高瑞麟, 金鑫, 刘璐, 李朝将, Songlin DING. 不锈钢增材制造件后处理工艺研究进展[J]. 航空学报, 2022, 43(4): 525847-525847.

LI Hui, LI Guangxian, GAO Ruilin, JIN Xin, LIU Lu, LI Chaojiang, Songlin DING. Research progress of post-processing of stainless steel additive manufacturing parts[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525847-525847.

参考文献

[1] 卢秉恒. 增材制造技术:现状与未来[J]. 中国机械工程, 2020, 31(1):19-23. LU B H. Additive manufacturing-Current situation and future[J]. China Mechanical Engineering, 2020, 31(1):19-23(in Chinese).
[2] 熊云龙, 娄延春, 刘新峰. 不锈钢材料研究的新进展[J]. 热加工工艺, 2005, 34(5):51-53. XIONG Y L, LOU Y C, LIU X F. New progress of stainless steel[J]. Hot Working Technology, 2005, 34(5):51-53(in Chinese).
[3] 周建涛. 硬质合金刀具车削半奥氏体沉淀硬化不锈钢的磨损机理研究[D]. 济南:山东大学, 2010:1-2. ZHOU J T. Wear mechanisms of cemented carbide tools in turning of semi-austenitic precipitation hardening stainless steel[D]. Jinan:Shandong University, 2010:1-2(in Chinese).
[4] 张国平. 不锈钢切削加工[J]. 现代机械, 2013(1):65-67, 70. ZHANG G P. Stainless steel cutting processing[J]. Modern Machinery, 2013(1):65-67, 70(in Chinese).
[5] 周芳娟. 304不锈钢切削加工表面特性的研究[D]. 武汉:华中科技大学, 2014:1-2. ZHOU F J. Research on machined surface characteristics of304Stainless steel[D]. Wuhan:Huazhong University of Science and Technology, 2014:1-2(in Chinese).
[6] 章媛洁, 宋波, 赵晓, 等. 激光选区熔化增材与机加工复合制造AISI 420不锈钢:表面粗糙度与残余应力演变规律研究[J]. 机械工程学报, 2018, 54(13):170-178. ZHANG Y J, SONG B, ZHAO X, et al. Selective laser melting and subtractive hybrid manufacture AISI420 stainless steel:Evolution on surface roughness and residual stress[J]. Journal of Mechanical Engineering, 2018, 54(13):170-178(in Chinese).
[7] 方金祥. 激光熔覆成形马氏体不锈钢应力演化及调控机制[D]. 哈尔滨:哈尔滨工业大学, 2016:2-3. FANG J X. Evolution and control of stress during laser cladding forming of martensitic stainless steel[D]. Harbin:Harbin Institute of Technology, 2016:2-3(in Chinese).
[8] EDWARDS P, RAMULU M. Fatigue performance evaluation of selective laser melted Ti-6Al-4V[J]. Materials Science and Engineering:A, 2014, 598:327-337.
[9] ZHU J H, ZHOU H, WANG C, et al. A review of topology optimization for additive manufacturing:Status and challenges[J]. Chinese Journal of Aeronautics, 2021, 34(1):91-110.
[10] 耿海滨, 熊江涛, 黄丹, 等. 丝材电弧增材制造技术研究现状与趋势[J]. 焊接, 2015(11):17-21, 69. GENG H B, XIONG J T, HUANG D, et al. Research status and trends of wire and arc additive manufacturing technology[J]. Welding & Joining, 2015(11):17-21, 69(in Chinese).
[11] 熊江涛, 耿海滨, 林鑫, 等. 电弧增材制造研究现状及在航空制造中应用前景[J]. 航空制造技术, 2015, 58(增刊2):80-85. XIONG J T, GENG H B, LIN X, et al. Research status of wire and arc additive manufacture and its application in aeronautical manufacturing[J]. Aeronautical Manufacturing Technology, 2015, 58(Sup.2):80-85(in Chinese).
[12] PARVARESH B, SALEHAN R, MIRESMAEILI R. Investigating isotropy of mechanical and wear properties in as-deposited and inter-layer cold worked specimens manufactured by wire arc additive manufacturing[J]. Metals and Materials International, 2021, 27(1):92-105.
[13] American Society for Testing and Materials. Standard specification for chromium and chromium-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications:ASTM-A240/A240Ma-2002[S]. West Conshohocken:ASTM International, 2002.
[14] KONG D C, NI X Q, DONG C F, et al. Anisotropy in the microstructure and mechanical property for the bulk and porous 316L stainless steel fabricated via selective laser melting[J]. Materials Letters, 2019, 235:1-5.
[15] 刘奋成, 贺立华, 黄春平, 等. 316L不锈钢电弧堆焊快速成形工艺及组织性能研究[J]. 南昌航空大学学报(自然科学版), 2013, 27(4):1-5. LIU F C, HE L H, HUANG C P, et al. Microstructure, mechanical properties and processing study of arc overlying welding rapid forming of 316L stainless steel[J]. Journal of Nanchang Hangkong University (Natural Sciences), 2013, 27(4):1-5(in Chinese).
[16] CHEN X H, LI J, CHENG X, et al. Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing[J]. Materials Science and Engineering:A, 2017, 703:567-577.
[17] 周斌, 张婷, 林峰, 等. 电子束选区熔化成形Ti6Al4V和316L不锈钢叶轮体微观组织和力学性能的研究[J]. 稀有金属材料与工程, 2018, 47(1):175-180. ZHOU B, ZHANG T, LIN F, et al. Microstructures and mechanical properties of Ti6Al4V and 316L stainless steel impeller body made by electron beam selective melting[J]. Rare Metal Materials and Engineering, 2018, 47(1):175-180(in Chinese).
[18] KARLSSON J, SNIS A, ENGQVIST H, et al. Characteri-zation and comparison of materials produced by electron beam melting (EBM) of two different Ti-6Al-4V powder fractions[J]. Journal of Materials Processing Tech, 2013, 213(12):2109-2118.
[19] 王忻凯, 王乾俸. 增材制造及其航空航天领域的发展现状[J]. 中小企业管理与科技, 2015(12):230-231. WANG X K, WANG Q F. Additive manufacturing and its development status in aerospace field[J]. Management & Technology of SME, 2015(12):230-231(in Chinese).
[20] 席明哲, 高士友. 激光快速成形Rene 80高温合金组织及裂纹形成机理[J]. 中国激光, 2012, 39(8):0803008. XI M Z, GAO S Y. Microstructures and mechanism of cracks forming of Rene 80 high-temperature alloy fabricated by laser rapid forming process[J]. Chinese Journal of Lasers, 2012, 39(8):0803008(in Chinese).
[21] 宋建丽, 邓琦林, 葛志军, 等. 镍基合金激光快速成形裂纹控制技术[J]. 上海交通大学学报, 2006, 40(3):548-552. SONG J L, DENG Q L, GE Z J, et al. The cracking control technology of laser rapid forming nickel-based alloys[J]. Journal of Shanghai Jiao Tong University, 2006, 40(3):548-552(in Chinese).
[22] 杨健, 黄卫东, 陈静, 等. 激光快速成形金属零件的残余应力[J]. 应用激光, 2004, 24(1):5-8. YANG J, HUANG W D, CHEN J, et al. Residual stress on laser rapid forming metal part[J]. Applied Laser, 2004, 24(1):5-8(in Chinese).
[23] WITTIG B, ZINKE M, JVTTNER S. Influence of arc energy and filler metal composition on the microstructure in wire arc additive manufacturing of duplex stainless steels[J]. Welding in the World, 2021, 65(1):47-56.
[24] 张炼. 316不锈钢TIG电弧增材制造工艺及性能研究[D]. 大连:大连理工大学, 2019:9-10. ZHANG L. Research on process and performance of 316 stainless steel TIG arc additive manufacturing[D]. Dalian:Dalian University of Technology, 2019:9-10(in Chinese).
[25] XU X, MI G Y, LUO Y Q, et al. Morphologies, microstructures, and mechanical properties of samples produced using laser metal deposition with 316 L stainless steel wire[J]. Optics and Lasers in Engineering, 2017, 94:1-11.
[26] 李旭文, 宋刚, 张兆栋, 等. 激光诱导电弧复合增材制造316不锈钢的组织和性能[J]. 中国激光, 2019, 46(12):1202006. LI X W, SONG G, ZHANG Z D, et al. Microstructure and properties of 316 stainless steel produced by laser-induced arc hybrid additive manufacturing[J]. Chinese Journal of Lasers, 2019, 46(12):1202006(in Chinese).
[27] 齐海波, 林峰, 颜永年, 等. 316L不锈钢粉末的电子束选区熔化成形[J]. 清华大学学报(自然科学版), 2007, 47(11):1941-1944. QI H B, LIN F, YAN Y N, et al. Electron beam selective melting of 316L stainless steel powder[J]. Journal of Tsinghua University (Science and Technology), 2007, 47(11):1941-1944(in Chinese).
[28] 郭超, 林峰, 葛文君. 电子束选区熔化成形316L不锈钢的工艺研究[J]. 机械工程学报, 2014, 50(21):152-158. GUO C, LIN F, GE W J. Study on the fabrication process of 316L stainless steel via electron beam selective melting[J]. Journal of Mechanical Engineering, 2014, 50(21):152-158(in Chinese).
[29] 任香会, 张文杰, 易耀勇, 等. ER308L不锈钢丝材微束等离子弧增材制造组织与性能分析[J]. 沈阳航空航天大学学报, 2019, 36(6):27-32. REN X H, ZHANG W J, YI Y Y, et al. Microstructure and mechanical properties of mateirals fabricated by micro-plasma arc additive manufacturing from ER308L wire[J]. Journal of Shenyang Aerospace University, 2019, 36(6):27-32(in Chinese).
[30] WANG Y D, TANG H B, FANG Y L, et al. Microstructure and mechanical properties of hybrid fabricated 1Cr12Ni2WMoVNb steel by laser melting deposition[J]. Chinese Journal of Aeronautics, 2013, 26(2):481-486.
[31] BENARJI K, RAVI KUMAR Y, JINOOP A N, et al. Effect of heat-treatment on the microstructure, mechanical properties and corrosion behaviour of SS 316 structures built by laser directed energy deposition based additive manufacturing[J]. Metals and Materials International, 2021, 27(3):488-499.
[32] 赵晓. 激光选区熔化成形模具钢材料的组织与性能演变基础研究[D]. 武汉:华中科技大学, 2016:140-142. ZHAO X. Fundamental research on the microstructure and properties evolution of tool steels fabricated by selective laser melting[D]. Wuhan:Huazhong University of Science and Technology, 2016:140-142(in Chinese).
[33] 程灵钰, 朱小刚, 刘正武, 等. 热处理对激光选区熔化成形316L不锈钢组织和力学性能的影响[J]. 材料热处理学报, 2020, 41(7):80-86. CHENG L Y, ZHU X G, LIU Z W, et al. Effect of heat treatment on microstructure and mechanical properties of 316L stainless steel prepared by selective laser melting[J]. Transactions of Materials and Heat Treatment, 2020, 41(7):80-86(in Chinese).
[34] 边培莹. 热处理工艺对316L不锈钢粉末激光选区熔化成形的残余应力及组织的影响[J]. 材料热处理学报, 2019, 40(4):90-97. BIAN P Y. Effect of heat treatment on residual stress and microstructure of 316L stainless steel powder formed by selective laser melting[J]. Transactions of Materials and Heat Treatment, 2019, 40(4):90-97(in Chinese).
[35] 徐亮, 杨可, 王秋雨, 等. 热处理对电弧增材制造316L不锈钢组织和性能的影响[J]. 电焊机, 2020, 50(10):29-34, 126. XU L, YANG K, WANG Q Y, et al. Effect of heat treatment on microstructure properties of austenitic stainless steel 316L using arc additive manufacturing[J]. Electric Welding Machine, 2020, 50(10):29-34, 126(in Chinese).
[36] 王智勇, 张毅, 王鑫, 等. 热处理工艺对G30钢组织和性能的影响[J]. 材料热处理学报, 2018, 39(7):92-98. WANG Z Y, ZHANG Y, WANG X, et al. Effect of heat treatment on microstructure and properties of G30 steel[J]. Transactions of Materials and Heat Treatment, 2018, 39(7):92-98(in Chinese).
[37] 王臣, 赵坤. 不锈钢的机械加工特性和方法探讨[J]. 装备制造技术, 2011(6):193-194. WANG C, ZHAO K. Discuss mechanical processing properties and methods of stainless steel[J]. Equipment Manufacturing Technology, 2011(6):193-194(in Chinese).
[38] 徐林红. 难加工材料可加工性分析方法的研究[D]. 武汉:武汉理工大学, 2010. XU L H. Research on the machinability evaluation method for difficult-to-cut materials[D]. Wuhan:Wuhan University of Technology, 2010(in Chinese).
[39] VENKATA RAO R. Machinability evaluation of work materials using a combined multiple attribute decision-making method[J]. The International Journal of Advanced Manufacturing Technology, 2006, 28(3-4):221-227.
[40] RAO R V, GANDHI O P. Digraph and matrix methods for the machinability evaluation of work materials[J]. International Journal of Machine Tools and Manufacture, 2002, 42(3):321-330.
[41] BOUBEKRI N, RODRIGUEZ J, ASFOUR S. Development of an aggregate indicator to assess the machinability of steels[J]. Journal of Materials Processing Technology, 2003, 134(2):159-165.
[42] ENACHE S, STRÂJESCU E, OPRAN C, et al. Mathematical model for the establishment of the materials machinability[J]. CIRP Annals, 1995, 44(1):79-82.
[43] LI G X, YI S, WEN C E, et al. Wear mechanism and modeling of tribological behavior of polycrystalline diamond tools when cutting Ti6Al4V[J]. Journal of Manufacturing Science and Engineering, 2018, 140(12):121011.
[44] LI G X, YI S, SUN S J, et al. Wear mechanisms and performance of abrasively ground polycrystalline diamond tools of different diamond grains in machining titanium alloy[J]. Journal of Manufacturing Processes, 2017, 29:320-331.
[45] ZHANG P R, DU J, ZHANG J J, et al. A theoretical model to study the cutting force characteristics in remanufacturing turning of laser cladded coatings[J]. The International Journal of Advanced Manufacturing Technology, 2021, 113(3-4):757-769.
[46] 白海清, 沈钰, 安熠蔚, 等. 304不锈钢与其激光熔覆件小孔钻削的对比研究[J]. 应用激光, 2020, 40(1):1-6. BAI H Q, SHEN Y, AN Y W, et al. Comparative study on small hole drilling of 304 stainless steel and its laser cladding parts[J]. Applied Laser, 2020, 40(1):1-6(in Chinese).
[47] 白海清, 沈钰, 舒林森, 等. 304不锈钢激光熔覆件的制备及小孔钻削实验研究[J]. 热加工工艺, 2020, 49(10):84-88, 91. BAI H Q, SHEN Y, SHU L S, et al. Preparation of laser cladding 304 stainless steel and experimental study on small hole drilling[J]. Hot Working Technology, 2020, 49(10):84-88, 91(in Chinese).
[48] 高飞, 白海清, 安熠蔚, 等. 316L不锈钢增材成型件小孔钻削试验研究[J]. 现代制造工程, 2019(9):48-53, 36. GAO F, BAI H Q, AN Y W, et al. Experimental research on small hole drilling of 316L stainless steel additive forming parts[J]. Modern Manufacturing Engineering, 2019(9):48-53, 36(in Chinese).
[49] 沈钰. 不锈钢激光熔覆件的小直径孔钻削试验研究[D]. 汉中:陕西理工大学, 2019:4-5. SHEN Y. Experimental research on small diameter hole drilling of stainless steel laser cladding[D]. Hanzhong:Shaanxi University of Technology, 2019:4-5(in Chinese).
[50] 安熠蔚, 白海清, 鲍骏, 等. 316L不锈钢激光熔覆成形件铣削表面质量分析[J]. 机床与液压, 2021, 49(22):61-66. AN Y W, BAI H Q, BAO J, et al. Analysis on milling surface quality of 316L stainless steel laser cladding forming parts[J]. Machine Tool & Hydraulics, 2021, 49(22):61-66(in Chinese).
[51] WANG G R, CHU F, TAO S Y, et al. Optimization design for throttle valve of managed pressure drilling based on CFD erosion simulation and response surface methodology[J]. Wear, 2015, 338-339:114-121.
[52] RAJESWARI B, AMIRTHAGADESWARAN K S. Experimental investigation of machinability characteristics and multi-response optimization of end milling in aluminium composites using RSM based grey relational analysis[J]. Measurement, 2017, 105:78-86.
[53] 郭鹏. 激光增材制造不锈钢的力学性能和铣削性能研究[D]. 济南:山东大学, 2017:69-70. GUO P. Study on mechanical properties and milling performance of stainless steel manufactured by laser additive manufacturing[D]. Jinan:Shandong University, 2017:69-70(in Chinese).
[54] MA M M, WANG Z M, GAO M, et al. Layer thickness dependence of performance in high-power selective laser melting of 1Cr18Ni9Ti stainless steel[J]. Journal of Materials Processing Technology, 2015, 215:142-150.
[55] TRIVEDI R, SEETHARAMAN V, ESHELMAN M A. The effects of interface kinetics anisotropy on the growth direction of cellular microstructures[J]. Metallurgical Transactions A, 1991, 22(2):585-593.
[56] OH J W, LOUCA L A, CHOO Y S. Strain rate effects on the response of stainless steel corrugated firewalls subjected to hydrocarbon explosions[J]. Journal of Constructional Steel Research, 2004, 60(1):1-29.
[57] KAYNAK Y, KITAY O. The effect of post-processing operations on surface characteristics of 316L stainless steel produced by selective laser melting[J]. Additive Manufacturing, 2019, 26:84-93.
[58] YAMAGUCHI H, FERGANI O, WU P Y. Modification using magnetic field-assisted finishing of the surface roughness and residual stress of additively manufactured components[J]. CIRP Annals, 2017, 66(1):305-308.
[59] CHOMIENNE V, VALIORGUE F, RECH J, et al. Influence of ball burnishing on residual stress profile of a 15-5PH stainless steel[J]. CIRP Journal of Manufacturing Science and Technology, 2016, 13:90-96.
[60] LI G X, RAHIM M Z, DING S L, et al. Performance and wear analysis of polycrystalline diamond (PCD) tools manufactured with different methods in turning titanium alloy Ti-6Al-4V[J]. The International Journal of Advanced Manufacturing Technology, 2016, 85(1-4):825-841.
[61] TAPOGLOU N, CLULOW J. Investigation of hybrid manufacturing of stainless steel 316L components using direct energy deposition[J]. Proceedings of the Institution of Mechanical Engineers, Part B:Journal of Engineering Manufacture, 2021, 235(10):1633-1643.
[62] GONG Y D, LI P F. Analysis of tool wear performance and surface quality in post milling of additive manufactured 316L stainless steel[J]. Journal of Mechanical Science and Technology, 2019, 33(5):2387-2395.
[63] BAI Q, WU B Z, QIU X L, et al. Experimental study on additive/subtractive hybrid manufacturing of 6511 steel:Process optimization and machining characteristics[J]. The International Journal of Advanced Manufacturing Technology, 2020, 108(5-6):1389-1398.
[64] TÖNSHOFF H K, ARENDT C, AMOR R B. Cutting of hardened steel[J]. CIRP Annals, 2000, 49(2):547-566.
[65] FANG J X, DONG S Y, WANG Y J, et al. The effects of solid-state phase transformation upon stress evolution in laser metal powder deposition[J]. Materials & Design, 2015, 87:807-814.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

不锈钢增材制造件后处理工艺研究进展

Research progress of post-processing of stainless steel additive manufacturing parts

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	司瑞, 陈勇. 民用飞机增材制造技术应用发展趋势[J]. 航空学报, 2024, 45(5): 529677-529677.
[2]	唐论, 余圣甫, 郑博, 史玉升, 陈颖. 圆柱面点阵自生Al₂O₃铝合金粉芯丝材开发及应用[J]. 航空学报, 2023, 44(9): 626864-626864.
[3]	张卫红, 周涵, 李韶英, 朱继宏, 周璐. 航天高性能薄壁构件的材料-结构一体化设计综述[J]. 航空学报, 2023, 44(9): 627428-627428.
[4]	林忠钦, 于忠奇, 戴冬华, 樊晓光, 余圣甫, 顾冬冬, 李淑慧, 史玉升. 复杂高筋薄壁构件旋压-增材复合制造技术发展与展望[J]. 航空学报, 2023, 44(9): 627493-627493.
[5]	顾孟奇, 朱家才, 郭万林, 薛松. 可重复使用运载火箭结构疲劳耐久性与可靠性展望[J]. 航空学报, 2023, 44(23): 628299-628299.
[6]	张志强, 勾青泽, 路学成, 王浩, 曹轶然, 郭志永. 高强铝合金CMT+P电弧增材制造熔滴过渡行为[J]. 航空学报, 2023, 44(13): 427881-427881.
[7]	路来骁, 徐长官, 刘建华, 秦美镇, 吕英波, 阎玉芹. 初始应力状态对薄壁件双侧滚压影响规律[J]. 航空学报, 2023, 44(10): 427415-427415.
[8]	刘振东, 郑锡涛, 范雯静, 张东健. 固化残余应力对无人机复合材料机翼强度的影响[J]. 航空学报, 2022, 43(6): 526117-526117.
[9]	姚燕生, 周瑞根, 张成林, 梅涛, 吴敏. 增材制造复杂金属构件表面抛光技术[J]. 航空学报, 2022, 43(4): 525202-525202.
[10]	张佩宇, 周鑫, 李应红. 单晶涡轮叶片高能束修复研究进展[J]. 航空学报, 2022, 43(4): 525610-525610.
[11]	李志强, 陈玮. 高能束流加工技术在航空领域的应用进展[J]. 航空学报, 2022, 43(4): 526882-526882.
[12]	李涤尘, 鲁中良, 田小永, 张航, 杨春成, 曹毅, 苗恺. 增材制造——面向航空航天制造的变革性技术[J]. 航空学报, 2022, 43(4): 525387-525387.
[13]	王天帅, 贺小帆, 王金宇, 李玉海. 基于双峰对数正态分布模型的DED-TA15钛合金DFR值估计方法[J]. 航空学报, 2022, 43(3): 225013-225013.
[14]	尚勇, 冯阳, 刘巧沐, 王君武, 杨惠君, 茹毅, 张恒, 赵文月, 裴延玲, 李树索, 宫声凯. 大型科学装置在航空发动机高温结构材料和涂层上的研究与应用[J]. 航空学报, 2022, 43(10): 527481-527481.
[15]	王连庆, 胡雅楠, 车志刚, 吴圣川. 激光冲击强化7075铝合金熔焊接头的疲劳性能[J]. 航空学报, 2021, 42(5): 524320-524320.