中心进气旋转盘腔换热特性对无量纲参数的敏感性分析

doi:10.7527/S1000-6893.2019.23017

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

中心进气旋转盘腔换热特性对无量纲参数的敏感性分析

丁水汀^1,2, 邓长春^1,2, 邱天^1,2

1. 北京航空航天大学能源与动力工程学院, 北京 100083;
2. 北京航空航天大学航空发动机气动热力国家级重点实验室, 北京 100083

收稿日期:2019-03-20 修回日期:2019-05-27 出版日期:2019-12-15 发布日期:2019-09-09
通讯作者: 邱天 E-mail:qiutian@buaa.edu.cn

Sensibility analysis of heat transfer characteristics to dimensionless criterion in central inlet rotating disk cavity

DING Shuiting^1,2, DENG Changchun^1,2, QIU Tian^1,2

1. School of Energy and Power Engineering, Beihang University, Beijing 100083, China;
2. National Key Laboratory of Science and Technology on Aero-Engine Aero-Thermodynamics, Beihang University, Beijing 100083, China

Received:2019-03-20 Revised:2019-05-27 Online:2019-12-15 Published:2019-09-09

摘要/Abstract

摘要： 针对早期旋转盘腔换热特性研究中常忽略压缩性和耗散效应影响的研究方法，在定几何、常物性、可压缩、有耗散假设下，对描述旋转盘腔系统的控制方程进行了无量纲分析，得到除无量纲空间位置外的7个无量纲准则数。利用数值模拟的方法探究了中心进气转静系盘腔换热特性对7个无量纲参数的敏感性。结果表明：在本文研究的某些工况内，反映进口耗散效应的埃克特准则与反映转盘热边界的基比切夫准则以及固体的无量纲导热系数对努塞尔数的影响程度与旋转雷诺准则同量级。根据本文分析结果，给出了早期旋转盘腔换热特性研究成果在先进航空发动机旋转盘腔设计工作中应用的注意事项和工程建议。

关键词: 航空发动机, 旋转盘腔, 无量纲分析, 换热特性, 敏感性分析

Abstract: The early research method of rotating disk cavity heat transfer characteristics ignores the influence of compressibility and dissipation. To solve this problem, the governing equation describing the rotating disk cavity system is nondimensionalized under the assumptions of fixed geometry, constant physical property, being compressible, and being dissipative. Analysis yields 7 dimensionless criteria in addition to the dimensionless spatial location. The numerical simulation method is used to investigate the sensitivity of the heat transfer characteristics of the central inlet rotating disk cavity. The results show that in some working conditions, the Eckert criterion reflecting the inlet dissipation effect, the Kibitche criterion reflecting the thermal boundary influence of the disk, and the dimensionless thermal conductivity of the solid have the same magnitude of influence on the Nusselt number as the rotating Reynolds criterion. Based on the analyses this paper offers the precautions and engineering suggestions for the application of early rotating disk cavity heat transfer study results in the design of advanced aero-engine rotating disk cavity.

Key words: aero-engine, rotating disk cavity, dimensionless analysis, heat transfer characteristics, sensibility analysis

中图分类号:

V231

丁水汀, 邓长春, 邱天. 中心进气旋转盘腔换热特性对无量纲参数的敏感性分析[J]. 航空学报, 2019, 40(12): 123017-123017.

DING Shuiting, DENG Changchun, QIU Tian. Sensibility analysis of heat transfer characteristics to dimensionless criterion in central inlet rotating disk cavity[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(12): 123017-123017.

参考文献 23

[1]	OWEN J M, ROGER R H. Flow and heat transfer in rotating-disc systems, Vol 1:Rotor-stator systems[M]. New York:Research Studies Press, 1989:50-250.
[2]	LUO X, WANG L, ZHAO X, et al. Experimental investigation of heat transfer in a rotor-stator cavity with cooling air inlet at low radius[J]. International Journal of Heat and Mass Transfer, 2014, 76:65-80.
[3]	WILSON M, PILBROW R, OWEN J M. Flow and heat transfer in a pre-swirl rotor-stator system:95-GT-239[R]. New York:ASME, 1995.
[4]	LOCK G D, WILSON M, OWEN J M. Influence of fluid dynamics on heat transfer in a preswirl rotating-disk system[J]. Journal of Engineering for Gas Turbines and Power, 2005, 127(4):791-797.
[5]	KAKADE V U, LOCK G D, OWEN J M, et al. Accurate heat transfer measurements using thermochromic liquid crystal. Part 2:Application to a rotating disc[J]. International Journal of Heat and Fluid Flow, 2009, 30(5):950-959.
[6]	KAKADE V U, LOCK G D, OWEN J M, et al. Effect of radial location of nozzles on heat transfer in pre-swirl cooling systems:GT2009-59090[R]. New York:ASME, 2009.
[7]	DIBELIUS G H, HEINEN M. Heat transfer from a rotating disc:90-GT-219[R]. New York:ASME, 1990.
[8]	BUNKER R S, METZGER D E, WITTIG S. Local heat transfer in turbine disk-cavities:Part II-Rotor cooling with radial location injection of coolant:90-GT-026[R]. New York:ASME, 1990.
[9]	徐国强, 丁水汀,邱绪光,等. 具有中心进气外缘加热旋转盘的局部换热特性研究[J]. 航空动力学报, 1995, 10(3):299-309. XU G Q, DING S T, QIU X G, et al. An investigation on local heat transfer performance for rim heated rotating disk with central air inflow[J]. Journal of Aerospace Power, 1995, 10(3):299-309(in Chinese).
[10]	徐国强. 转静系旋转盘腔内冷气的流动与换热特性研究[D]. 北京:北京航空航天大学, 1999:14-23. XU G Q. Flow and heat transfer characteristics of coolant through a shrouded rotating disk system[D]. Beijing:Beihang University, 1999:14-23(in Chinese).
[11]	丁水汀. 高位进气、径向出流的旋转空腔内冷气的流动与换热特性研究[D]. 北京:北京航空航天大学, 1999:17-27. DING S T. Investigation of fluid flow and heat transfer characteristics within a rotating cavity with high positioned axial inlet and radial outlet[D]. Beijing:Beihang University, 1999:17-27(in Chinese).
[12]	罗翔, 徐国强,陶智,等. 30°预旋进气旋转盘流动与换热特性的实验[J]. 北京航空航天大学学报, 2007, 33(3):290-293. LUO X, XU G Q, TAO Z, et al. Flow and heat transfer in rotor stator system with per-swirl angle of 30°[J]. Journal of Beijing University of Aeronautics and Astronautics, 2007, 33(3):290-293(in Chinese).
[13]	罗翔, 徐国强,陶智,等. 进气角度对旋转盘冷却效果的影响[J]. 推进技术, 2007, 28(3):240-243. LUO X, XU G Q, TAO Z, et al. Cooling effectiveness in a rotor stator system with different pre-swirl angles[J]. Journal of Propulsion Technology, 2007, 28(3):240-243(in Chinese).
[14]	王锁芳, 朱强华, 栾海峰,等. 高位预旋进气转静盘腔换热实验[J]. 航空动力学报, 2007, 22(8):1216-1221. WANG S F, ZHU Q H, LUAN H F, et al. Experimental study on heat transfer in rotor stator cavity with high positioned pre-swirl inflow[J]. Journal of Aerospace Power, 2007, 22(8):1216-1221(in Chinese).
[15]	赵熙. 复杂涡轮盘腔内流动与换热特性研究[D]. 北京:北京航空航天大学, 2012:6-50. ZHAO X. Study on fluid flow and heat transfer in rotor-stator turbine disc cavities with complex boundary conditions[D]. Beijing:Beihang University, 2012:6-50(in Chinese).
[16]	DAILY J W, NECE R E. Chamber dimension effects on induced flow and frictional resistance of enclosed rotating disks[J]. Journal of Basic Engineering, 1960, 82(1):217-232.
[17]	DORFMAN L A. Hydrodynamic resistance and the heat loss of rotating solids[M]. Edinburgh:Oliver and Boyd, 1963.
[18]	DORFMAN L A. Influence of the radial temperature gradient on the heat transfer from a rotating disk[J]. Izv. Akad. Nauk SSSR. Otd. Tehn. Nauk, 1957(12):64-66(in Russian).
[19]	丁水汀, 张弓,李烨. 旋转盘腔盘缘热流密度的敏感性分析[J]. 推进技术, 2012, 33(2):263-268. DING S T, ZHANG G, LI Y. Sensibility analysis of the heat flux in the rotating cavity[J]. Journal of Propulsion Technology, 2012, 33(2):263-268(in Chinese).
[20]	陶智, 徐国强,丁水汀,等. 航空发动机传热学[M]. 1版. 北京:北京航空航天大学出版社, 2005:256-264. TAO Z, XU G Q, DING S T, et al. Aero-engine heat transfer[M]. 1st ed. Beijing:Beihang University Press, 2005:256-264(in Chinese).
[21]	丁水汀, 付德斌,罗翔,等. 浮升力对双旋转轴间流动换热影响的数值模拟[J]. 推进技术, 2003, 24(6):543-546. DING S T, FU D B, LUO X, et al. Numerical investigation for the influence of buoyancy on heat transfer in an annulus between rotating cylinders with turbulent axial flow[J]. Journal of Propulsion Technology, 2003, 24(6):543-546(in Chinese).
[22]	BARDINA J E, HUANG P G, COAKLEY T J. Turbulence modeling validation, testing, and development:NASA-TM-110446[R]. Washington, D.C.:NASA, 1997.
[23]	LITTELL H S, EATON J K. Turbulence characteristics of the boundary layer on a rotating disk[J]. Journal of Fluid Mechanics, 1994, 266:175-207.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

中心进气旋转盘腔换热特性对无量纲参数的敏感性分析

Sensibility analysis of heat transfer characteristics to dimensionless criterion in central inlet rotating disk cavity

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献 23

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘佳奇, 冯蕴雯, 路成, 薛小锋, 潘维煌. 基于智能神经网络的航空发动机运行安全分析[J]. 航空学报, 2022, 43(9): 625375-625375.
[2]	张烁, 刘治汶. 航空发动机轴承故障结构化贝叶斯稀疏表示[J]. 航空学报, 2022, 43(9): 625056-625056.
[3]	牛广越, 段发阶, 周琦, 刘志博. 基于微波相位差测距的叶尖间隙动态测量方法[J]. 航空学报, 2022, 43(9): 625396-625396.
[4]	张忠强, 张新, 王家序, 刘治汶. 基于重加权谱峭度方法的航空发动机故障诊断[J]. 航空学报, 2022, 43(9): 625445-625445.
[5]	杨晓伟, 葛曜文, 邓文翔, 姚建勇, 周宁. 航空发动机导叶控制机构作动筒主动容错控制[J]. 航空学报, 2022, 43(9): 625464-625464.
[6]	韩淞宇, 邵海东, 姜洪开, 张笑阳. 基于提升卷积神经网络的航空发动机高速轴承智能故障诊断[J]. 航空学报, 2022, 43(9): 625479-625479.
[7]	杜建建, 潘贤德, 刘天一. 航空发动机角接触球轴承轴向力间接测量方法[J]. 航空学报, 2022, 43(9): 625457-625457.
[8]	曹明, 王鹏, 左洪福, 曾海军, 孙见忠, 杨卫东, 魏芳, 陈雪峰. 民用航空发动机故障诊断与健康管理现状、挑战与机遇Ⅱ: 地面综合诊断、寿命管理和智能维护维修决策[J]. 航空学报, 2022, 43(9): 625574-625574.
[9]	段发阶, 牛广越, 周琦, 傅骁, 蒋佳佳. 航空发动机叶尖间隙在线测量技术研究综述[J]. 航空学报, 2022, 43(9): 626014-626014.
[10]	王睿, 周洲, 郭荣化, 黄悦琛. 太阳能无人机伞降着陆多体动力学仿真与试验[J]. 航空学报, 2022, 43(8): 225721-225721.
[11]	郑覃, 杨小贺, 叶俊, 冯锦璋. 内涵工况对风扇增压级双涵匹配的影响[J]. 航空学报, 2022, 43(7): 125477-125477.
[12]	李定骏, 杨镠育, 孙帆, 江鹏, 陈艺文, 王铁军. 预热温度对热障涂层表面裂纹形成的影响[J]. 航空学报, 2022, 43(6): 526184-526184.
[13]	汪博, 高培鑫, 马辉, 孙伟, 林君哲, 李晖, 韩清凯, 刘中华. 航空发动机管路系统动力学特性综述[J]. 航空学报, 2022, 43(5): 25332-025332.
[14]	张冬辉, 张泰华, 崔燕香, 陈臣, 王生. 平流层系留气球气动参数敏感性分析[J]. 航空学报, 2022, 43(5): 125083-125083.
[15]	靳玉林, 刘治汶, 陈予恕. 航空发动机双转子系统叶片-机匣碰摩故障模拟[J]. 航空学报, 2022, 43(12): 425072-425072.