基于CFD的高速切削层流模拟

doi:10.7527/S1000-6893.2013.0109

Abstract

Abstract:

In high speed metal cutting, the irreversible dislocation motion and multiplication result in the plastic deformation of the metal, and its velocity are proportional to the drag force of the solid. Therefore, the effect of viscosity becomes more and more important in describing the material dynamic behavior. The damping mechanism of dislocation in high speed metal cutting is described from the fluid aspect; a model for high speed machining is established based on fluid mechanics. The velocity distribution, the pressure distribution and the strain rate distribution are calculated by solving the Navier-Stokes equation and energy equation, which provides a new method to study high speed machining. Analytical results show that approximating the behavior of metal cutting by a fluid model during high speed machining is not irrelevant. A speed stagnation point is located at some distance from the tool tip on the tool rake face on which the maximum value of the pressure occurs, with zero speed. Its location influences the life of the tool and the quality of the finished surface. The pressure decreases along the rake face and reaches zero at some point away from the tool tip, which is the point of separation of the chip from the tool. The value of the strain rate exhibits a rapid increase from the tool tip to the free surface corner, and then decreases outwards.

Key words: fluid mechanics, high speed machining, strain rate, stagnation point, cutting tool

CLC Number:

V252
TG506.1

ZHANG Keguo, LIU Zhanqiang, WAN Yi. Laminar Flow Analog for High Speed Machining Based on CFD[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, doi: 10.7527/S1000-6893.2013.0109.

References

[1] Merchant M E. Mechanics of metal-cutting process. Journal of Applied Physics, 1945, 16(5): 267-275.

[2] Lee E H, Shaffer B W. The theory of plasticity applied to a problem of machining. Journal of Applied Mechanics, 1952, 19(2): 234-239.

[3] Oxley P L B. Mechanics of machining: an analytical approach to assessing machinability. Chichister: Ellis Horwood, 1989: 242.

[4] Khludkva A N. Plastic strain energy in ultrafast metal cutting. Russian Physics Journal, 1978, 21(11): 1501- 1502.

[5] Zhang X T, Jia G H. Debris analysis of on-orbit satellite collision based on hypervelocity impact simulation. Acta Aeronautica et Astronautica Sinica, 2011, 32(7): 1224-1230. (in Chinese) 张晓天, 贾光辉. 基于超高速碰撞仿真的卫星碰撞解体碎片分析. 航空学报, 2011, 32(7):1224-1230.

[6] Shaw M C. The size effect in metal cutting. Sadhana, 2003, 28: 875-896.

[7] Yang G T. Dynamic theory of plasticity. Beijing:Higher Education Press. 2000:7-10. (in Chinese) 杨桂通. 塑性动力学. 北京: 高等教育出版社, 2000: 7-10.

[8] El-Zahry R M. On the hydrodynamic characteristics of the secondary shear zone in metal machining with sticking-sliding friction using the boundary layer theory. Wear, 1987, 115(3): 349-359.

[9] Kwon K B, Cho D W, Lee S J, et al. A fluid dynamic analysis model of the ultra-precision cutting mechanism. ClRP Annals-Manfacturing Technology, 1999, 48(1): 43-46.

[10] Kazban R V. Effect of tool parameters on residual stress and temperature generation in high-speed machining of aluminum alloys. Indiana:University of Notre Dame, 2005: 37-39.

[11] Liu Z Q, Zhang K G. Sensitivity analysis of Johnson-Cook material constants on adiabatic shear. Acta Aeronautica et Astronautica Sinica, 2011, 32(11): 2140-2146. (in Chinese) 刘战强, 张克国. J-C本构参数对绝热剪切影响的敏感性分析.航空学报, 2011, 32(11): 2140-2146.

[12] He N, Lee T C. Assessment of deformation of a locallized chip in high speed machining. Journal of Materials Processing Technology, 2002, 129: 101-104.

[13] Bi X F, Liu Y X. Calculating strain rate and strain during orthogonal cutting in accordance to streamline theory. Journal of Northeastern University, 2009, 30(8): 1185-1188. (in Chinese) 毕雪峰, 刘永贤. 基于流线理论计算正交切削中应变率和应变的方法.东北大学学报, 2009, 30(8):1185-1188.

[14] Meyers M A. Dynamic behavior of materials. Zhang Q M, Liu Y, translated. Beijing: National Defence Industry Press, 2006: 230-240. (in Chinese) Meyers M A. 材料的动态力学行为. 张庆明, 刘彦, 译. 北京: 国防工业出版社, 2006: 230-240.

[15] Cheng J Y, Zhou G Q. A new theory of dislocation motion and its application to description of dynamic mechanical behavior of materials. Acta Metallurgica Sinica, 1995, 31(10): 431-437. (in Chinese) 程经毅, 周光泉. 一种新的位错运动理论及对材料动态力学行为的描述. 金属学报, 1995, 31(10): 431-437.

[16] Orowan E. Problems of plastic gliding. Proceedings of the Physical Society,1940, 52: 8.

[17] Parameswaran V R,Weertman J. Dislocation mobility in lead and Pb-In alloy single crystals. Metallurgical and Materials Transactions B, 1971, 2(4): 1233-1243.

[18] Su G S. Evolution and mechanisms of saw-tooth chip formation in high-speed machining. Jinan: School of Mechanical Engineering, Shandong University, 2011. (in Chinese) 苏国胜. 高速切削锯齿形切屑形成过程与形成机理研究. 济南:山东大学机械学院, 2011.

[19] Li G H, Wang M J, Duan C Z, et al. Finite element simulation of the process of orthogonal metal cutting based on the ANSYS/LS-DYNA. Transactions of the Chinese Society of Agricultural Machinery, 2007, 38(12):173-176. (in Chinese) 李国和, 王敏杰, 段春争, 等. 基于ANSYS/LS-DYNA的金属切削过程有限元模拟, 农业机械学报, 2007, 38(12): 173-176.

[20] Guo Y B, Yen D W. A FEM study on mechanisms of discontinuous chip formation in hard machining. Journal of Materials Processing Technology, 2004, 155-156: 1350-1356.

[21] Srinivasan K. Experimental determination of strain rate and flow stress in the primary shear zone while machining AISI 4340 and Ti-6AL-4V. Wichita: the Department of Industrial and Manufacturing Engineering, Wichita State University, 2010.

Laminar Flow Analog for High Speed Machining Based on CFD

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	WANG Yuexin, HE Huan, WU Tian, XI Xulong. Modified method for impact response prediction of scaled model based on loss function [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(8): 225781-225781.
[2]	LI Qing, TU Guohua, YU Zhaosheng, LIN Zhaowu, LI Tingting, YUAN Xianxu. Inertial particle transport in non-uniform accelerated flow [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(S1): 726390-726390.
[3]	YAN Yanyan, ZHANG Yafei, ZHANG Zhaoqing. Surface and subsurface damage mechanisms in tangential ultrasonic-assisted grinding of ZrO₂ ceramics [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(7): 624749-624749.
[4]	WANG Yixing, HAN Renkun, LIU Ziyang, ZHANG Yang, CHEN Gang. Progress of deep learning modeling technology for fluid mechanics [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(4): 524779-524779.
[5]	CHEN Yueliang, ZHANG Zhuzhu, BIAN Guixue, ZHANG Yong, HUANG Hailiang. Dynamic mechanical behavior and failure model of 38CrMoAl steel under high strain rate [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(10): 423709-423709.
[6]	DU Maohua, CHENG Zheng, WANG Shensong, ZHANG Yanfei. Effects of damage evolution on simulation results of high speed machining of Ti6Al4V [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(7): 422787-422787.
[7]	HAN Zhirong, ZHAO Keliang, YAN Wei. Application of Gurney flap in hybrid-wing design for icing wind tunnel [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(2): 522387-522387.
[8]	ZHANG Keguo, LIU Yong, WANG Yan'gang. Strain rate on material deformation in high speed metal cutting process [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(3): 421757-421757.
[9]	YAO Xiaohu, ZHANG Longhui, ZHANG Xiaoqing, GUO Weiguo, ZANG Shuguang. Experimental study on dynamic mechanical behavior of aerospace- transparent polyurethane interlayer [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2015, 36(7): 2236-2243.
[10]	KONG Jinxing, CHEN Hui, HE Ning, LI Liang, JIANG Feng. Dynamic Mechanical Property Tests and Constitutive Model of Pure Iron Material [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2014, 35(7): 2063-2071.
[11]	LIANG Xiao, WANG Honglun, LI Dawei, LÜ Wentao. Three-dimensional Path Planning for Unmanned Aerial Vehicles Based on Principles of Stream Avoiding Obstacles [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2013, 34(7): 1670-1681.
[12]	WANG Tao, CHEN Guoding, JU Jiangtao. Experimental Study of Constitutive Relationship of Superalloy GH4169 Under High Strain Rates [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2013, 34(4): 946-953.
[13]	LI Zhibing, CHEN Zhitong, WANG Shuang, XU Rufeng. 5-Axis Machining Technology of Turbine Blade's Root Area in Stripe-width-maximization Method with Torus Cutter [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2011, 32(9): 1722-1731.
[14]	LIU Zhanqiang, ZHANG Keguo. Sensitivity Analysis of Johnson-Cook Material Constants on Adiabatic Shear [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2011, 32(11): 2140-2146.
[15]	Huang Shuoqiao;Shen Gongxin;Robert Konrath;Carl F.v. Carmer;Kompenhans Jürgen. Experimental Investigation of Influence of Jets on Aircraft Wake Vortices [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2010, 31(5): 899-908.