基于3D打印的舵面可调实用化飞机风洞模型的设计与试验

doi:10.7527/S1000-6893.2013.0347

Abstract

Abstract:

As keys for wind tunnel testing, design and fabrication of aircraft model are critical to the development cycle and cost of aircraft. To improve the efficiency of aircraft development, a practical method based on 3D printing technology to design and fabricate model is proposed in the paper.A full low-speed model of one real aircraft is designed and evaluated. The modelis in a plastic-metal hybrid structure, with the 3D printing-made plastic parts as its aerodynamic contour outside and machined metal parts as its backbone inside. V-shaped brackets and shaft-pin mechanisms are adopted to adjust deflection angles of control surfaces.As an attempt to eliminate the precision loss of plastic parts due to abrasion during assembly, metal bushes are custom-designed and inset into the plastic holes. Passing the strength/stiffness calibration based on computational fluid dynamic-computational structure dynamic (CFD/CSD) calculation, the assembled model is tested in the FD-09 low-speed wind tunnel. The hybrid model can be used safely in the testing condition when the angle of attack is 8° and the wind speed is 70 m/s. The aerodynamic data from the hybrid model is in consistent well with those from the metal one, which indicates the practicability of the new method to design and fabricate aircraft models. Compared with the metal model, the time and cost concerning design and fabrication of the hybrid model is reduced remarkably, and it can meet the demand of aircraft engineers for the fast and low-cost models and could be promising to improve the development efficiency of aircraft.

Key words: wind tunnel testing, wind tunnel model, adjustable control surface, 3D printing, rapid prototyping, additive manufacturing, stereolithography

CLC Number:

ZHU Weijun, LI Dichen, REN Ke, ZHANG Zhengyu. Design and Test of a Practical Aircraft Model for Wind Tunnel Testing with Adjustable Control Surfaces Based on 3D Printing[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2014, 35(2): 400-407.

References

[1] Timothy G. Process improvement for aerodynamic model development, AIAA-2008-6364[R]. Reston: AIAA, 2008.

[2] Yun Q L. Wind tunnel testing[M]. Beijing: National Defense Industry Press, 2000: 53-55. (in Chinese) 恽起麟. 风洞试验[M]. 北京:国防工业出版社, 2000: 53-55.

[3] Guo H T, Lu B, Yu L, et al. Investigation on full-model flutter of a certain fighter plane in high-speed wind tunnel test[J]. Acta Aeronautica et Astronautica Sinica, 2012, 33(10): 1765-1771. (in Chinese) 郭洪涛, 路波, 余立, 等. 某战斗机高速全模颤振风洞试验研究[J]. 航空学报, 2012, 33(10): 1765-1771.

[4] Zhou Z H, Li D C, Zhang Z Y, et al. Design and fabrication of a hybrid surface-pressure airfoil model based on rapid prototyping[J]. Rapid Prototyping Journal, 2008, 14(1): 57-66.

[5] Yang D G, Zhang Z Y, Sun Y, et al. A preliminary design and manufacturing study of hybrid lightweight high-speed wind-tunnel models[J]. Rapid Prototyping Journal, 2011, 17(1): 45-54.

[6] Liu B S, Yan Y, Qian W, et al. Design, modal analysis and tests of composites wing box[J]. Journal of Beijing University of Aeronautics and Astronautics, 2003, 29(11): 1026-1028. (in Chinese) 刘兵山, 燕瑛, 钱卫, 等. 复合材料机翼盒段的设计、模态分析和试验[J]. 北京航空航天大学学报, 2003, 29(11): 1026-1028.

[7] Zeng D, Yan Y, Liu B S, et al. Design of low-velocity wing tunnel flutter model of aircraft composite structure[J]. Acta Aeronautica et Astronautica Sinica, 2006, 27 (2): 232-235 (in Chinese) 曾东, 燕瑛, 刘兵山, 等. 复合材料飞机结构低速风洞颤振模型的设计[J]. 航空学报, 2006, 27(2): 232-235

[8] Qian W, Wu J P, Zhao T M, et al. Design of a structurally dynamic-similar models for flutter wind tunnel testing[C]//First National Aerospace Symposium on Mehanical Problems in the Aerospace Field, 2004: 153-156. (in Chinese) 钱卫, 吴江鹏, 赵铁铭, 等. 颤振风洞试验中结构相似动力学模型的设计[C]//首届全国航空航天领域中的力学问题学术研讨会, 2004: 153-156.

[9] Zhang J J, Yang Z C. Structural dynamics optimization design with constraints of multiple natural frequencies and modal shape[J]. Structure & Environment Engineering, 2007, 34(1):11-16. (in Chinese) 张锦江, 杨智春. 具有多阶频率与振型约束的结构动力学优化设计[J]. 强度与环境, 2007, 34(1):11-16.

[10] Zhu W J, Li D C, Zhang Z Y, et al. Design and fabrication of stereolithography-based aeroelastic wing models[J]. Rapid Prototyping Journal, 2011, 17(4): 298-307.

[11] Bird J. Exploring the 3D printing opportunity[N/OL].The financial times. London, 2012-08-08.http://www.ft.com/intl/cms/s/0/6dc11070-d763-11e1-a378-00144feabdc0. html#axzz2jUZ0k7de

[12] The White House. We can't wait: Obama administration announces new public-private partnership to support[EB/OL]. The White House Office of the Press Secretary. Washington DC, 2012-08-16.http://www.whitehouse.gov/the-press-office/2012/08/16/we-can-t-wait-obama-administration-announces-new-public-private-partners

[13] Springer A. Evaluating aerodynamic characteristics of wind-tunnel models produced by rapid prototyping methods[J]. Journal of Spacecraft and Rockets, 1998, 35(6): 755-759.

[14] Aghanajafi C, Daneshmand S, Nadooshan A A. Influence of layer thickness on the design of rapid-prototyped models[J]. Journal of Aircraft, 2009, 46(3): 981-987.

[15] Landrum D B, Beard R M, LaSarge P A, et al. Evaluation of stereolithography rapid prototyping for low speed airfoil design, AIAA-1997-0719[R]. Reston: AIAA, 1997.

[16] Chuk R N, Thomos V J. A comparison of rapid prototyping techniques used for wind tunnel model fabrication[J]. Rapid Prototyping Journal, 1998, 4(4): 185-196.

[17] Azarov Y A, Vermel V D, Kornushenko A V, et al. Experience in laser stereolithography and its application in manufacturing wind-tunnel aerodynamic models of various purposes[C]. Suzdal, Russia: SPIE, 2002: 433-440.

[18] Zhou Z H, Li D C, Zeng J H, et al. Rapid fabrication of metal-coated composite stereolithography parts[J]. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2007, 221(9): 1431-1440.

[19] Li D C, Zeng J H, Zhou Z H, et al. Fabrication of aircraft wind tunnel model using stereolithography[J]. Aeronautical Manufacturing Technology, 2008, (8): 26-29. (in Chinese) 李涤尘, 曾俊华, 周志华, 等. 光固化快速成形飞机风洞模型制造方法[J]. 航空制造技术, 2008, (8): 26-29.

[20] Zhu W J, Li D C, Zhang Z Y, et al. The rapidly fabrication technique for wind-tunnel models of flight vehicle[J]. Journal of Experiments in Fluid Mechanics, 2011, (5): 79-84. (in Chinese) 朱伟军, 李涤尘, 张征宇, 等. 飞行器风洞模型的快速制造技术[J]. 实验流体力学, 2011, (5): 79-84.

[21] Reeder M F, Allen W, Phillips J M, et al. Wind-tunnel measurements of the E-8C modeled with and without winglets[J]. Journal of Aircraft, 2008, 45(1): 345-348.

[22] Tyler C, Braisted W, Higgins J. Evaluation of rapid prototyping technologies for use in wind tunnel model fabrication, AIAA-2005-1301[R]. Reston: AIAA, 2005.

[23] Tyler C, Schwartz R J, Fleming G, et al. Rapid prototyping-unmanned combat air vehicle (UCAV)/sensor craft, AFRL-RB-WP-TR-2008-3034[R]. Wright-Patterson Air Force Base: Air Force Research Laboratory, 2008.

[24] Zhang W, Li D C, Zhao X L, et al. Fabrication and performance evaluation of micro-channels in aircraft wind-tunnel-models for pressure measurements using stereolithography[J]. Acta Aeronautica et Astronautica Sinica, 2011, 32(12): 2335-2340. (in Chinese) 张威, 李涤尘, 赵星磊, 等. 基于光固化快速成型技术的测压风洞模型孔道制造与性能评价[J]. 航空学报, 2011, 32(12): 2335-2340.

[25] Li D C, Zhou Z H, Lu B H, et al. Fabrication and assembly of resin-metal hybrid aircraft models for wind tunnel testing based on stereolithography: China, ZL200510124555.8[P]. 2005-12-15. (in Chinese) 李涤尘, 周志华, 卢秉恒, 等. 光固化成形的树脂-金属复合型飞机风洞模型制作与装配: 中国, ZL200510124555.8[P]. 2005-12-15.

Design and Test of a Practical Aircraft Model for Wind Tunnel Testing with Adjustable Control Surfaces Based on 3D Printing

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	LI Dichen, LU Zhongliang, TIAN Xiaoyong, ZHANG Hang, YANG Chuncheng, CAO Yi, MIAO Kai. Additive manufacturing—Revolutionary technology for leading aerospace manufacturing [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525387-525387.
[2]	YAO Yansheng, ZHOU Ruigen, ZHANG Chenglin, MEI Tao, WU Min. Surface polishing technology for additive manufacturing of complex metal components [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525202-525202.
[3]	ZHANG Peiyu, ZHOU Xin, LI Yinghong. Progress on high energy beam repair of single crystal turbine blades [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525610-525610.
[4]	LI Hui, LI Guangxian, GAO Ruilin, JIN Xin, LIU Lu, LI Chaojiang, Songlin DING. Research progress of post-processing of stainless steel additive manufacturing parts [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525847-525847.
[5]	LI Zhiqiang, CHEN Wei. Application progress of power beam processing technology in aeronautical industry [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 526882-526882.
[6]	WANG Tianshuai, HE Xiaofan, WANG Jinyu, LI Yuhai. Estimation method for DFR value of DED-TA15 titanium alloy based on bimodal lognormal distribution [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(3): 225013-225013.
[7]	PENG Jinfeng, WU Dongrun, CUI Weiyun, CAI Deng'an, ZHOU Guangming. Design and analysis of simulated ice with 3D printed sandwich composite material [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(9): 224536-224536.
[8]	SHI Binbin, CHEN Zhehan. Defect detection method of powder bed based on image feature fusion [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524430-524430.
[9]	HUANG Jieguang, QI Lehua, LUO Jun. Experimental research and regulation mechanism of critical parameters on horizontal ejection of metal droplets [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524637-524637.
[10]	CHEN Xiangming, YAO Liaojun, GUO Licheng, SUN Yi. 3D printed continuous fiber-reinforced composites: State of the art and perspectives [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524787-524787.
[11]	CAO Longchao, ZHOU Qi, HAN Yuanfei, SONG Bo, NIE Zhenguo, XIONG Yi, XIA Liang. Review on intelligent monitoring of defects and process control of selective laser melting additive manufacturing [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524790-524790.
[12]	GU Dongdong, ZHANG Han, LIU Gang, YANG Biqi. Process optimization of additive manufactured sandwich panel structure using rare earth element modified high-performance Al alloy [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524868-524868.
[13]	GUO Xinxin, CHEN Zhehan. Numerical simulation of laser additive manufacturing process: A review [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524227-524227.
[14]	YUAN Jingwei, LI Zhuo, TANG Haibo, CHENG Xu. Effect of heat treatment on corrosion resistance and room temperature compression creep of LAMed TC4 alloy [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524390-524390.
[15]	DONG Jingang, XIE Feng, ZHANG Chenkai, MA Handong, QIN Yongming. Gravity effects of light model method in wind tunnel model drop-test [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(6): 523434-523434.