旋转裂纹叶片-弹性轮盘耦合系统振动特性

doi:10.7527/S1000-6893.2021.25442

航空发动机运行安全专栏

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

旋转裂纹叶片-弹性轮盘耦合系统振动特性

吴志渊¹, 闫寒¹, 吴林潮¹, 马辉², 瞿叶高¹, 张文明¹

1. 上海交通大学机械系统与振动国家重点实验室, 上海 200240;
2. 东北大学机械工程与自动化学院, 沈阳 110819

收稿日期:2021-03-03 修回日期:2021-04-07 出版日期:2022-09-15 发布日期:2021-06-29
通讯作者: 张文明,E-mail:wenmingz@sjtu.edu.cn E-mail:wenmingz@sjtu.edu.cn
基金资助:
国家科技重大专项(2017-V-0009)；国家自然科学基金(11972112)

Vibration characteristics of rotating cracked-blade-flexible-disk coupling system

WU Zhiyuan¹, YAN Han¹, WU Linchao¹, MA Hui², QU Yegao¹, ZHANG Wenming¹

1. State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai 200240, China;
2. School of Mechanical Engineering and Automation, Northeastern University, Shenyang 110819, China

Received:2021-03-03 Revised:2021-04-07 Online:2022-09-15 Published:2021-06-29
Supported by:
National Science and Technology Major Project (2017-V-0009);National Natural Science Foundation of China (11972112)

摘要/Abstract

摘要： 航空发动机叶片长期在复杂激励的恶劣环境中工作, 极易造成损伤产生裂纹, 导致叶片-轮盘耦合系统的模态特性发生改变, 偏离初始设计状态。以旋转裂纹叶片-弹性轮盘系统为研究对象, 基于Kirchhoff板理论和Timoshenko梁理论模拟弹性轮盘和旋转叶片, 基于释放应变能和Castigliano原理将叶片裂纹等效为旋转刚度, 建立了裂纹叶片-弹性轮盘耦合系统连续体动力学模型；通过模态实验和有限元方法验证了提出方法的正确性；并分析了裂纹深度、裂纹位置、轮盘厚度和转速对裂纹叶片-弹性轮盘耦合系统固有特性的影响。研究结果表明：叶片裂纹导致初始正交的叶片-轮盘耦合模态振型破坏, 出现模态局部化现象, 且随着裂纹深度增大, 相应的频率减小；裂纹位置靠近叶尖, 模态局部化现象消失, 形成两阶正交模态；随着轮盘厚度的增加, 发生频率转向现象, 叶片弯曲模态与多个轮盘振型相关；随着转速的增加, 发生频率转向现象, 以及在高转速下叶片弯曲模态与其余阶次叶片弯曲模态相关。

关键词: 旋转裂纹叶片, 弹性轮盘, 模态实验, 有限元方法, 频率转向, 模态局部化

Abstract: Being exposed to severe environments with complex excitation for a long time, aero-engine blades can easily cause damage and cracks, which will change the modal characteristics of the blade-disk coupling system and deviate from the initial design state. Taking the rotating cracked-blade-flexible-disk coupling system as the research object, a dynamic model is established, in which the flexible disk and rotating blades are investigated based on Kirchhoff plate and Timoshenko beam theories; the blade crack is equivalent to the rotational stiffness based on the released strain energy and Castigliano's theorem. The proposed method is verified by modal test and finite element method. In addition, the effects of crack length, crack position, disk thickness and rotating speed on the inherent characteristics of the coupling system are investigated. The research results show that: the crack leads to the destruction of the initial orthogonal blade-disk coupling modal and the phenomenon of modal localization, and the corresponding frequencies decrease with the increase of the crack length; the closer the crack position is to the blade tip, the modes localization disappears, and two-order orthogonal modes are formed; with the increase of the disk thickness, the frequency veering phenomenon occurs, and the blade-bending mode is related to multi-order modes of the disk; with the increase of speed, the frequency veering phenomenon occurs, and the blade-bending mode is related to the rest blade-bending modes at the high rotational speed.

Key words: rotating cracked blade, flexible disk, modal test, finite element method, frequency veering, modal localization

中图分类号:

V231.96

吴志渊, 闫寒, 吴林潮, 马辉, 瞿叶高, 张文明. 旋转裂纹叶片-弹性轮盘耦合系统振动特性[J]. 航空学报, 2022, 43(9): 625442-625442.

WU Zhiyuan, YAN Han, WU Linchao, MA Hui, QU Yegao, ZHANG Wenming. Vibration characteristics of rotating cracked-blade-flexible-disk coupling system[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(9): 625442-625442.

参考文献

[1] LIU M R, ZHU J, LIANG E B, et al. Vibration measurement on compressor rotor blades of aero-engine based on tip-timing[J]. Journal of Aerospace Power, 2019, 34(9): 1895-1904 (in Chinese). 刘美茹, 朱靖, 梁恩波, 等. 基于叶尖定时的航空发动机压气机叶片振动测量[J]. 航空动力学报, 2019, 34(9): 1895-1904.
[2] LIU M R, TENG G R, XIAO X, et al. Vibration measurement of turbine rotor blades of aero-engine based on blade tip-timing[J]. Journal of Aerospace Power, 2020, 35(9): 1954-1963 (in Chinese). 刘美茹, 滕光蓉, 肖潇, 等. 基于叶尖定时的航空发动机涡轮叶片振动测量[J]. 航空动力学报, 2020, 35(9): 1954-1963.
[3] ZENG J, CHEN K K, MA H, et al. Vibration response analysis of a cracked rotating compressor blade during run-up process[J]. Mechanical Systems and Signal Processing, 2019, 118: 568-583.
[4] XU H L. Research on key technology of crack detection in rotating blades by non-contact on-line blade tip-timing method[D]. Changsha: National University of Defense Technology, 2018: 1-18 (in Chinese). 徐海龙. 旋转叶片裂纹的叶端定时非接触在线检测关键技术研究[D]. 长沙: 国防科技大学, 2018: 1-18.
[5] LESAFFRE N, SINOU J J, THOUVEREZ F. Stability analysis of rotating beams rubbing on an elastic circular structure[J]. Journal of Sound and Vibration, 2007, 299(4-5): 1005-1032.
[6] CARASSALE L, MAURICI M, TRAVERSONE L. Reduced-order modeling of compressor blades by 1D finite elements[C]//Proceedings of ASME Turbo Expo 2015: Turbine Technical Conference and Exposition, 2015.
[7] SUN Q, MA H, ZHU Y P, et al. Comparison of rubbing induced vibration responses using varying-thickness-twisted shell and solid-element blade models[J]. Mechanical Systems and Signal Processing, 2018, 108: 1-20.
[8] LIU C, JIANG D X. Crack modeling of rotating blades with cracked hexahedral finite element method[J]. Mechanical Systems and Signal Processing, 2014, 46(2): 406-423.
[9] XIE J S, ZI Y Y, ZHANG M Q, et al. A novel vibration modeling method for a rotating blade with breathing cracks[J]. Science China Technological Sciences, 2019, 62(2): 333-348.
[10] BEHZAD M, GHADAMI A, MAGHSOODI A, et al. Vibration based algorithm for crack detection in cantilever beam containing two different types of cracks[J]. Journal of Sound and Vibration, 2013, 332(24): 6312-6320.
[11] DADO M H F, ABUZEID O. Coupled transverse and axial vibratory behaviour of cracked beam with end mass and rotary inertia[J]. Journal of Sound and Vibration, 2003, 261(4): 675-696.
[12] ZHAO C G, ZENG J, MA H, et al. Dynamic analysis of cracked rotating blade using cracked beam element[J]. Results in Physics, 2020, 19: 103360.
[13] YANG L H, YANG Z S, MAO Z, et al. Dynamic characteristic analysis of rotating blade with transverse crack—part Ⅰ: Modeling, modification, and validation[J]. Journal of Vibration and Acoustics, 2021, 143(5): 051010.
[14] HUANG B W, KUANG J H. Variation in the stability of a rotating blade disk with a local crack defect[J]. Journal of Sound and Vibration, 2006, 294(3): 486-502.
[15] KUANG J H, HUANG B W. The effect of blade crack on mode localization in rotating bladed disks[J]. Journal of Sound and Vibration, 1999, 227(1): 85-103.
[16] HUANG B W. Effect of number of blades and distribution of cracks on vibration localization in a cracked pre-twisted blade system[J]. International Journal of Mechanical Sciences, 2006, 48(1): 1-10.
[17] FANG X, TANG J, JORDAN E, et al. Crack induced vibration localization in simplified bladed-disk structures[J]. Journal of Sound and Vibration, 2006, 291(1-2): 395-418.
[18] SHE H X, LI C F, TANG Q S, et al. Veering and merging analysis of nonlinear resonance frequencies of an assembly bladed disk system[J]. Journal of Sound and Vibration, 2021, 493: 115818.
[19] CHIU Y J, HUANG S C. The influence of a cracked blade on rotor's free vibration[J]. Journal of Vibration and Acoustics, 2008, 130(5): 054502.
[20] YUAN H Q. Rotor dynamics fundamentals[M]. Beijing: Metallurgical Industry Press, 2013: 227-235 (in Chinese). 袁惠群. 转子动力学基础[M]. 北京: 冶金工业出版社, 2013: 227-235.
[21] MA H, LU Y, WU Z Y, et al. A new dynamic model of rotor-blade systems[J]. Journal of Sound and Vibration, 2015, 357: 168-194.
[22] OKABE A, KUDO T, SHIOHATA K, et al. Reduced modeling for turbine rotor-blade coupled bending vibration analysis[J]. Journal of Engineering for Gas Turbines and Power, 2012, 134(2): 022502.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

旋转裂纹叶片-弹性轮盘耦合系统振动特性

Vibration characteristics of rotating cracked-blade-flexible-disk coupling system

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	万傲霜, 王振名, 李顶河. 基于三阶剪切计算连续性方法的编织复合材料板三尺度分析模型[J]. 航空学报, 2022, 43(12): 226614-226614.
[2]	石文泽, 陈巍巍, 卢超, 程进杰, 陈尧. 高温铝合金电磁超声检测回波特性及因素分析[J]. 航空学报, 2020, 41(12): 423854-423854.
[3]	刘鹏, 郭亚洲, 赵振强, 邢军, 张超. 二维三轴编织复合材料压缩失效行为的细观有限元模拟[J]. 航空学报, 2019, 40(7): 222865-222865.
[4]	田硕, 尚建勤, 盖鹏涛, 陈福龙, 曾元松. 带筋整体壁板预应力喷丸成形数值模拟及变形预测[J]. 航空学报, 2019, 40(10): 422847-422847.
[5]	路来骁, 孙杰, 韩雄, 熊青春, 宋戈. 基于能量理论的航空整体结构件滚压变形校正载荷预测方法[J]. 航空学报, 2017, 38(12): 421326-421326.
[6]	刘洋, 刘战强, 宋清华. 约束阻尼型镗杆的优化及减振性能[J]. 航空学报, 2016, 37(6): 1992-2002.
[7]	梁珩, 曾建江, 易礼毅, 童明波. 高超声速飞行器多层次结构强度分析方法[J]. 航空学报, 2016, 37(2): 588-596.
[8]	余雄庆, 欧阳星, 邢宇, 王宇. 机翼结构重量预测的多学科分析优化方法[J]. 航空学报, 2016, 37(1): 235-243.
[9]	陈晖, 谭昌柏, 王志国. 耦合几何与材料误差的柔性装配偏差统计分析[J]. 航空学报, 2015, 36(9): 3176-3186.
[10]	刘莉, 陈树霖, 周思达, 陈昭岳. 脉冲子结构与有限元刚-弹混合连接的子结构方法[J]. 航空学报, 2015, 36(8): 2670-2680.
[11]	白天, 朱春玲, 苗波, 李清英, 张泉. 平面铝板上的压电振动除冰方法[J]. 航空学报, 2015, 36(5): 1564-1573.
[12]	余家泉, 许进升, 陈雄, 周长省, 贾登, 李宏文. 推进剂/包覆层界面脱粘率相关特性研究[J]. 航空学报, 2015, 36(12): 3861-3867.
[13]	曲巍崴, 方垒, 柯映林, 方伟, 刘思仁, 邢宏文. 环形轨道制孔系统定位方法分析[J]. 航空学报, 2014, 35(8): 2319-2330.
[14]	张超, 许希武, 严雪. 纺织复合材料细观力学分析的一般性周期性边界条件及其有限元实现[J]. 航空学报, 2013, 34(7): 1636-1645.
[15]	聂少云, 吴志刚. 考虑预应力和液体影响的圆柱壳颤振分析 [J]. 航空学报, 2012, (5): 855-862.