| [1] Cai Y L, Xi G, Wang S J. The generation of tool path for clean-up machining of impeller[J]. Mechanical Design, 2001, 18(11): 37-40. (in Chinese) 蔡永林, 席光, 王尚锦. 叶轮加工中清根刀心轨迹的生成[J]. 机械设计, 2001, 18(11): 37-40.[2] Liu C M, Yan G R, Xu H F. The research of automatic clean-up tool-path generation based on stock-remaining model[J]. Journal of Engineering Graphics, 2001, 22(1): 39-46. (in Chinese) 刘长明, 闫光荣, 许鹤峰. 基于留量模型的自动清根技术的研究[J]. 工程图学学报, 2001, 22(1): 39-46.[3] Robert G, Lin T W, Lin A C. Planning of tool orientation for five-axis cavity machining[J]. The International Journal of Advanced Manufacturing Technology, 2003, 22(1-2): 150-160.[4] Zhu W H, Lee Y S. Five-axis pencil-cut planning and virtual prototyping with 5-DOF haptic interface[J]. Computer-Aided Design, 2004, 36(13): 1295-1307.[5] Ren Y F, Yau H T, Lee Y S. Clean-up tool path generation by contraction tool method for machining complex polyhedral models[J]. Computers in Industry, 2004, 54(1): 17-33.[6] Hu H B. The research of the algorithm of four-axis blade clean-up machining and process plan optimizing[D]. Xi'an: Northwestern Polytechnical University, 2005. (in Chinese) 胡海滨. 叶片四轴清根加工算法及工艺优化方案研究[D]. 西安: 西北工业大学, 2005.[7] Tang M, Zhang D H, Luo M, et al. Tool path generation for clean-up machining of impeller by point-searching based method[J]. Chinese Journal of Aeronautics, 2012, 25(1): 131-136.[8] Ni Y R. Optimal torus-shaped end-mill orientation control for 5-axis sculptured structure NC machining and graphics simulation[D]. Beijing: Beihang University, 1999. (in Chinese) 倪炎榕. 环面刀具五坐标数控加工复杂曲面优化刀位计算与图形显示[D]. 北京: 北京航空航天大学, 1999.[9] Xu R F. Research on tool position error calculation and tool path planning methods in 5-axis machining of sculptured surfaces[D]. Beijing: Beihang University, 2010. (in Chinese) 徐汝锋. 宽行加工刀位误差求解与刀轨规划技术研究[D]. 北京: 北京航空航天大学, 2010.[10] Xu R F, Chen W Y, Chen Z T. A tool positioning algorithm through longitude separation approach for a cutter with non-circle generatrix[J]. Acta Aeronautica et Astronautica Sinica, 2010, 31(2): 410-417. (in Chinese) 徐汝锋, 陈五一, 陈志同. 基于经线划分的非圆截面环形刀具刀位优化算法[J]. 航空学报, 2010, 31(2): 410-417.[11] Li Z Q, Chen Z T, Xiao J. Latitude distribution algorithm of cutter position optimization on drum-like cutter for strip-maximization[J]. Journal of Beijing University of Aeronautics and Astronautics, 2007, 33(6): 731-735. (in Chinese) 李正强, 陈志同, 肖俊. 鼓形刀宽行刀位优化纬线分割算法[J]. 北京航空航天大学学报, 2007, 33(6): 731-735.[12] Ni Y R, Ma D Z, Zhang H, et al. Optimal orientation control for torus tool 5-axis sculptured surface NC machining[J]. Chinese Journal of Mechanical Engineering, 2001, 37(2): 87-91. (in Chinese) 倪炎榕, 马登哲, 张洪, 等. 圆环面刀具五坐标数控加工复杂曲面优化刀位算法[J]. 机械工程学报, 2001, 37(2): 87-91.[13] Yan J Y, Chen Z T, He Y. A quick calculation method of tool position error based on envelop theory[J]. Acta Aeronautica et Astronautica Sinica, 2011, 32(11): 2131-2139. (in Chinese) 颜家勇, 陈志同, 贺英. 基于包络理论的刀位误差快速求解算法[J]. 航空学报, 2011, 32(11): 2131-2139.[14] Li Z B, Chen Z T, Wang S, et al. 5-axis machining technology of turbine blade's root area in stripe-width-maximation method with torus cutter[J]. Acta Aeronautica et Astronautica Sinica, 2011, 32(9): 1722-1731. (in Chinese) 李志兵, 陈志同, 王爽, 等. 基于环面刀具的叶片过渡区域宽行加工技术[J]. 航空学报, 2011, 32(9): 1722-1731.[15] Wang X W. The strip-width maximization machining algorithm based on tool center-driven with torus cutter[D]. Beijing: Beihang University, 2013. (in Chinese) 王小文. 基于刀心驱动的环面刀具加工算法[D]. 北京: 北京航空航天大学, 2013.[16] Yan J Y. Research on the strip-with maximization machining algorithm based on surface sectional curves discretization[D]. Beijing: Beihang University, 2011. (in Chinese) 颜家勇. 基于曲面截型线分划的宽行加工算法研究[D]. 北京: 北京航空航天大学, 2011. |
CJA
