民用飞机弹性结构水上迫降试验载荷研究

doi:10.7527/S1000-6893.2013.0416

固体力学与飞行器总体设计

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

民用飞机弹性结构水上迫降试验载荷研究

徐文岷, 李凯

上海飞机设计研究院强度设计研究部, 上海 201210

收稿日期:2013-07-18 修回日期:2013-10-07 出版日期:2014-04-25 发布日期:2013-10-21
通讯作者: 徐文岷，Tel.：021-31225958 E-mail：xuwenmin@comac.cc E-mail:xuwenmin@comac.cc
作者简介:徐文岷男，硕士，工程师。主要研究方向：民用飞机水上迫降试验与数值模拟分析，飞机起落架强度。Tel：021-31225958 E-mail：xuwenmin@comac.cc；李凯男，本科，研究员。主要研究方向：民用飞机水上迫降试验与数值模拟分析，飞机结构强度。Tel：021-31225844 E-mail：likai@comac.cc
基金资助:
工信部民机科研项目

Research on Civil Aircraft Elastic Structure Ditching Test Load

XU Wenmin, LI Kai

Stress Department, Shanghai Aircraft Design and Research Institute, Shanghai 201210, China

Received:2013-07-18 Revised:2013-10-07 Online:2014-04-25 Published:2013-10-21
Supported by:
CCTIME Civil Aircraft Research Project

摘要/Abstract

摘要：

刚体模型和弹性体模型的载荷传递方式不同，为了研究刚体模型和弹性结构模型对飞机水上迫降载荷的影响，根据动力相似性原理设计制造了刚体模型，并根据强度相似性原理设计制造了弹性结构部件，通过气囊加载试验系统验证了弹性结构部件满足强度相似设计要求。通过水上迫降模型试验测得加速度-时间历程曲线，使用傅里叶变换处理试验数据得到加速度峰值。根据刚体模型的试验数据分析，飞机以初始俯仰角12°、襟翼为着陆构型、较小的下沉速度和中重心状态入水时，飞机在水上迫降过程中受到的载荷较小。研究表明：带弹性结构模型和刚体模型所得到的飞机载荷有明显的不同，带弹性结构模型得到的垂向加速度峰值明显低于刚体模型。这种现象主要是由于机体着水底部弹性结构变形吸收了大量的能量。

关键词: 水上迫降, 动力模型, 弗劳德数, 相似性, 弹性结构, 民用飞机

Abstract:

Load transfer is different between rigid model and elastic structure model. In order to research the impact of rigid model and an elastic structure model on ditching loads, a rigid model is designed and manufactured, based on the principle of dynamic similarity and the elastic structural part is designed and manufactured based on the principle of strength similarity, which is validated by an airbag loading test system. Through the ditching model tests acceleration-time history curves are obtained and peak acceleration value is obtained by processing the experimental data with Fourier transform. According to the rigid model experimental data analysis, the aircraft is subjected to a relatively small load in ditching with the following parameters: pitch 12°, flaps in landing configuration for minimum speed and middle center of gravity. The results indicate that the load is obviously different on the model with an elastic structural part and on the rigid model. The peak value of vertical acceleration of the model with elastic structure part is obviously smaller than that of the rigid model. This phenomenon is mainly due to energy absorption by the bottom elastic structure of fuselage.

Key words: ditching, dynamic models, Froude number, similarity, elastic structure, civil aircraft

中图分类号:

徐文岷, 李凯. 民用飞机弹性结构水上迫降试验载荷研究[J]. 航空学报, 2014, 35(4): 1012-1018.

XU Wenmin, LI Kai. Research on Civil Aircraft Elastic Structure Ditching Test Load[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2014, 35(4): 1012-1018.

参考文献

[1] Li B, Yang Z C. Large transport aircraft ditching research//2007 Annual Conference of Chinese Society of Aeronautics and Astronautics, 2007. (in Chinese) 李斌, 杨智春. 大型运输机水上迫降研究进展//中国航空学会2007年学术年会, 2007.

[2] National Transportation Safety Board. Loss of thrust in both engines after encountering a flock of birds and subsequent ditching on the Hudson River, NTSB/AAR-10/03. Weehawken, NJ: US Airways Flight 1549, 2010.

[3] Yang Q Y, Lv A Q, Duan G J, et al. American aircraft successful ditching on Hudson River case study[J]. China Emergency Rescue, 2009(3): 29-31. (in Chinese) 杨庆勇, 吕安勤, 段贵军, 等. 美客机迫降哈德逊河成功施救案例研究[J]. 中国应急救援, 2009(3): 29-31.

[4] CCAR-25-R4. Chinese civil aviation regulations Part 25, airworthiness standards: transport category airplanes[S]. Beijing: Civil Aviation Administration of China, 2011. (in Chinese) CCAR-25-R4. 中国民用航空规章运输类飞机适航标准[S]. 北京: 中国民用航空局, 2011.

[5] CCAR-121-R4. Chinese civil aviation regulations Part 121 R4, operating requirements: domestic, flag, and supplemental operations[S]. Beijing: Civil Aviation Administration of China, 2010. (in Chinese) CCAR-121-R4.大型飞机公共航空运输承运人运行合格审定规则[S]. 北京: 中国民用航空局, 2010.

[6] Thompson W C. Model ditching investigation of the Boeing 707 jet transport, RM-SL55K08. Washington D.C.: National Advisory Committee for Aeronautics, 1955.

[7] Thompson W C. Rough-water ditching investigation of a model of a jet transport with the landing gear extended and with various ditching aids, NACA-TN-3775. Washington D.C.: National Advisory Committee for Aeronautics, 1959.

[8] Thompson W C. Model ditching investigation of a jet transport airplane with various engine installations, L56G10. Washington D.C.: National Advisory Committee for Aeronautics, 1956.

[9] Wang Y H. How to determine the performance of the aircraft ditching[J]. International Aviation, 1989(11): 61.(in Chinese) 王雨和. 如何确定飞机水上迫降性能[J]. 国际航空, 1989(11): 61.

[10] Shah S. Water impact investigations for aircraft ditching analysis. Melbourne: College of Science, Engineering and Health, RMIT University, 2010.

[11] DOT/FAA/AR-95/54 Transport water impact and ditching performance[S]. Washington D.C.: Office of Avation Research, 1996.

[12] AC25-17A Transport airplane cabin interiors crashworthiness handbook[S]. Washington D.C.: U.S. Department of Transportation, 2005.

[13] Xu W M. Transport aircraft model ditching reserch[J]. Civil Aircraft Design and Reserach, 2010(S2): 60-62. (in Chinese) 徐文岷. 民用飞机水上迫降模型试验研究[J].民用飞机设计与研究, 2010(S2): 60-62.

[14] Mo N R. Engineering fluid dynamics[M]. Wuhan:Huazhong University of Science & Technology Press, 2000: 230-233. (in Chinese) 莫乃榕.工程流体力学[M]. 武汉:华中科技大学出版社, 2000: 230-233.

[15] Long T Y, Cai Z J. Fluid dynamics[M]. Beijing: China Architecture & Building Press, 2004: 263-265. (in Chinese) 龙天渝, 蔡增基. 流体力学[M]. 北京:中国建筑工业出版社, 2004: 263-265.

[16] Huang Y, Li K, Xu W M. Civil transport ditching loads prediction method study//10th National Conference on Vibration Theory and Application, 2011: 1138-1147. (in Chinese) 黄勇, 李凯, 徐文岷. 民用飞机水上迫降数水载荷预测方法研究//第十届全国振动理论及应用学术会议论文集, 2011: 1138-1147.

[17] Thomas W L. Ditching investigation of a 1/20-scale model of the space shuttle orbiter, NASA CR-2593. Washington D.C.: National Aeronautics and Space Administration, 1975.

[18] Chen S, Yang Z C, Li B. Design method of uniform loading system using airbag in structure test[J]. Engineering Mechanics, 2012, 29(6): 146-150. (in Chinese) 陈帅, 杨智春, 李斌. 结构试验中均布载荷的气囊加载系统设计方法[J]. 工程力学, 2012, 29(6): 146-150.

[19] Fisher L J, Morris G J. Ditching tests of a 1/18-scale model of the lockheed constellation airplane, NACA RM L8K18. Washington D.C.: National Aeronautics and Space Administration, 1950.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

民用飞机弹性结构水上迫降试验载荷研究

Research on Civil Aircraft Elastic Structure Ditching Test Load

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘小川, 惠旭龙, 张欣玥, 白春玉, 闫亚斌, 李肖成, 牟让科. 典型民用飞机全机坠撞实验研究[J]. 航空学报, 2024, 45(5): 529664-529664.
[2]	司瑞, 陈勇. 民用飞机增材制造技术应用发展趋势[J]. 航空学报, 2024, 45(5): 529677-529677.
[3]	李勐, 陈星伊, 陈吉昌, 吴彬, 童明波. 波浪情况下民机水上迫降性能数值分析[J]. 航空学报, 2024, 45(2): 28-43.
[4]	郑云隆, 刘沛清, 屈秋林, 戴佳骅, 田逾. BWB飞机水上迫降运动特性数值研究[J]. 航空学报, 2023, 44(21): 528588-528588.
[5]	贺媛媛, 杨炫, 韩慧, 王琦琛, 张航. 基于蜻蜓翅几何及刚度相似性的仿生扑翼结构[J]. 航空学报, 2023, 44(14): 227987-227987.
[6]	毕文豪, 范秋岑, 李德林, 张安. 基于多视角的民机正向设计建模方法[J]. 航空学报, 2023, 44(10): 227536-227536.
[7]	费钟阳, 蒋相闻, 招启军. 基于动态RCS特征相似的直升机靶机旋翼设计[J]. 航空学报, 2022, 43(7): 125465-125465.
[8]	李宇飞, 田威, 李波, 张楠. 机器人铣削系统精度控制方法及试验[J]. 航空学报, 2022, 43(5): 625815-625815.
[9]	张桢锴, 贾思嘉, 宋晨, 杨超. 柔性变弯度后缘机翼的风洞试验模型优化设计[J]. 航空学报, 2022, 43(3): 226071-226071.
[10]	童明波, 陈吉昌, 李乐, 肖天航, 古彪, 董登科, 汪正中. 飞行器水载荷结构完整性数值模拟现状与展望-Part I:水上迫降和水上漂浮[J]. 航空学报, 2021, 42(5): 524530-524530.
[11]	杨志刚, 张炯, 李博, 曾锐, 毛研勋. 民用飞机智能飞行技术综述[J]. 航空学报, 2021, 42(4): 525198-525198.
[12]	孙霄剑, 罗明强, 张驰, 关若曦, 刘虎. 民用飞机预研论证权威真相源构建技术[J]. 航空学报, 2021, 42(2): 224222-224222.
[13]	张杰, 季宝宁, 杨宁, 唐文斌. 一种装配体模型的离散量化与相似性分析方法[J]. 航空学报, 2021, 42(10): 524992-524992.
[14]	宋宏川, 詹浩, 魏中成, 任浩雷, 夏露. 基于XML的飞行仿真气动力模型存储格式[J]. 航空学报, 2020, 41(9): 123766-123766.
[15]	石章虎, 何晓煦, 曾德标, 雷沛. 基于误差相似性的移动机器人定位误差补偿[J]. 航空学报, 2020, 41(11): 424105-424105.