航空学报 > 2014, Vol. 35 Issue (5): 1424-1432   doi: 10.7527/S1000-6893.2013.0420

双酚A型环氧树脂紫外光固化工艺及其力学性能

刘博, 李勇, 肖军, 陈云雷, 肖健   

  1. 南京航空航天大学 材料科学与技术学院, 江苏 南京 210016
  • 收稿日期:2013-07-14 修回日期:2013-10-14 出版日期:2014-05-25 发布日期:2013-10-23
  • 通讯作者: 李勇,Tel.:025-84892980 E-mail:lyong@nuaa.edu.cn E-mail:lyong@nuaa.edu.cn
  • 作者简介:刘博男,硕士研究生。主要研究方向:先进复合材料工艺及性能。Tel:025-84892980E-mail:liuboccme@nuaa.edu.cn;李勇男,博士,教授,博士生导师。主要研究方向:先进复合材料自动化成型工艺及其设备、先进复合材料三维增强成型及性能。Tel:025-84892980E-mail:lyong@nuaa.edu.cn
  • 基金资助:

    国家科技支撑计划(2012BAA01B02)

UV-curing Process and Mechanical Properties of Bisphenol A Epoxy Resin

LIU Bo, LI Yong, XIAO Jun, CHEN Yunlei, XIAO Jian   

  1. College of Material Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
  • Received:2013-07-14 Revised:2013-10-14 Online:2014-05-25 Published:2013-10-23
  • Supported by:

    National Key Technology Research and Development Program of China (2012BAA01B02)

摘要:

为了推进紫外光固化技术在环氧树脂及其复合材料制备中的应用,以双酚A型环氧树脂E51为基体,采用自行研制的紫外光设备固化,利用红外光谱法测定固化后树脂的固化度,研究了树脂体系中光引发剂和稀释剂含量对树脂固化速率的影响以及环氧树脂的紫外光固化特性,获得的树脂体系的最优配方为:双酚A型环氧树脂E51:活性稀释剂660A:光引发剂1176=100:10:5(质量比),并对紫外光固化树脂浇铸体的力学性能进行了测试,其拉伸强度和模量分别可达到32.34 MPa和1.80 GPa,弯曲强度和模量分别为60.64 MPa和1.73 GPa。结果表明,紫外光固化速率随树脂体系中光引发剂含量的增加而上升,随活性稀释剂含量的增加先上升后下降;与传统热固化相比,紫外光固化不仅可以大幅度缩短树脂体系的固化时间,同时,制得的树脂浇铸体具有良好的综合力学性能。研究结果对紫外光固化技术在实际生产中的应用具有重要意义。

关键词: 环氧树脂, 紫外光固化, 阳离子光固化, 红外光谱, 力学性能

Abstract:

In order to promote the application of UV-curing technology in the curing of epoxy resin and its composites, UV-curing of bisphenol A epoxy resin is studied, with the use of a self-developed curing equipment. The curing degree of the resin is measured by the FTIR spectrometry. The curing characteristics and effects of the concentration of both photoinitiator and active diluents on curing rate of the resin are investigated. On this basis, the optimal proportion for the UV-curing system is obtained as 100 to 10 to 5 mass ratio of epoxy E51 to active diluents 660A to photoinitiator 1176. The mechanical properties of UV-cured specimens are also investigated, the tensile strength and modulus can reach 32.34 MPa and 1.80 GPa and the flexural strength and modulus are 60.64 MPa and 1.73 GPa, respectively. The results reveal that the curing rate of the resin is raised up with the increasing of the photoinitiator amount. And it increases initially with the increasing of the active diluents amount, while decreases at higher concentrations. Compared with thermal curing, UV-curing technology can greatly shorten the curing time, while the mechanical properties of the UV-cured products are favorable. The research results have great significance for the application of UV-curing technology in the practical production.

Key words: epoxy resins, UV-curing, photoinitiated cationic polymerization, infrared spectrometry, mechanical property

中图分类号: