航空发动机机匣摆线粗加工轨迹规划方法

doi:10.7527/S1000-6893.2017.21814

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

航空发动机机匣摆线粗加工轨迹规划方法

王晶, 罗明, 吴宝海, 张定华

西北工业大学现代设计与集成制造技术教育部重点实验室, 西安 710072

收稿日期:2017-10-19 修回日期:2017-12-07 出版日期:2018-06-15 发布日期:2017-12-07
通讯作者: 张定华,E-mail:dhzhang@nwpu.edu.cn E-mail:dhzhang@nwpu.edu.cn
基金资助:
国家自然科学基金（51575453）；国家科技重大专项（2015ZX04001202）

A trochoidal path planning method for rough machining of aeroengine casing parts

WANG Jing, LUO Ming, WU Baohai, ZHANG Dinghua

Key Laboratory of Contemporary Design and Integrated Manufacturing Technology, Ministry of Education, Northwestern Polytechnical University, Xi'an 710072, China

Received:2017-10-19 Revised:2017-12-07 Online:2018-06-15 Published:2017-12-07
Supported by:
National Natural Science Foundation of China (51575453); National Science & Technology Major Project (2015ZX04001202)

摘要/Abstract

摘要： 针对机匣零件粗加工过程中凸台多、加工余量大、材料难切削、刀具磨损快、加工周期长等特点，提出了一种机匣摆线粗加工刀具轨迹规划方法，该方法能有效控制切削过程中刀具负载的变化，改善刀具切削过程中的加热-冷却循环，减缓刀具的磨损，提高机匣粗加工效率。首先，通过对两种摆线模型的分析，建立了摆线铣数学模型，并分析了摆线铣的优缺点；其次，结合机匣零件特点，将模型在精度范围内离散为点模型，利用圆锥将模型展开并建立展开模型与原始模型间的映射关系。通过对可加工区域的划分和平面逼近，生成了适用于机匣零件的摆线粗加工刀具轨迹。最后，分别通过摆线铣刀具磨损实验、平面型腔摆线铣实验和机匣摆线铣实验，验证了摆线铣在降低刀具磨损、延长刀具寿命方面的有效性，以及本文轨迹生成算法在航空发动机机匣实际加工中的正确性和高效性。研究成果能有效缩短加工周期、降低加工成本，提升机匣零件的粗加工效率。

关键词: 摆线铣, 航空发动机机匣, 区域划分, 轨迹规划, 点模型

Abstract: To overcome the problems in rough machining of casing parts such as multiple bosses, large machining allowance, low machinability of materials, fast tool wear and long process cycle, a tool-path planning method for the trochoidal milling of the aeroengine casing is proposed, with which the change of the tool load can be controlled effectively, the heating-cooling cycle is improved, the tool wear is retarded, and the machining efficiency can be increased in the rough machining process of casing. First of all, through an analysis of two trochoidal models, a mathematical model for the trochoidal milling is developed, and the advantages as well as the disadvantages of the trochoidal milling are discussed. Then, based on the characteristics of the casing parts, the model is discretized into a point model in the accuracy range. The model is unfolded by using the cone, and the mapping relationship between the unfolded model and the original one is established. According to the division and plane approximation of the machining area, the tool path of trochoidal rough machining for casing parts is generated. Finally, experiments on the trochoidal milling of tool wear, planar cavity and casing show that the trochoidal milling is effective in reducing the tool wear and prolonging the tool life. The validity and high efficiency of the proposed trajectory generation algorithm in the actual processing of the aeroengine casing are verified. The research achievements can effectively shorten the processing cycle, reduce the machining costs and improve the rough machining efficiency of casing parts.

Key words: trochoidal milling, aeroengine casing, region division, path planning, point model

中图分类号:

V261
TP391.7

王晶, 罗明, 吴宝海, 张定华. 航空发动机机匣摆线粗加工轨迹规划方法[J]. 航空学报, 2018, 39(6): 421814-421814.

WANG Jing, LUO Ming, WU Baohai, ZHANG Dinghua. A trochoidal path planning method for rough machining of aeroengine casing parts[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(6): 421814-421814.

参考文献

[1] 王聪梅. 机匣制造技术[M]. 北京:科学出版社, 2002. WANG C M. Machining technology of casing[M]. Beijing:Science Press, 2002(in Chinese).
[2] 盛文娟, 徐斌. 航空发动机机匣电解加工工艺试验[J]. 电加工与模具, 2010(2):52-55. SHENG W J, XU B. Technological test of electrolytic machining of aero-engine casing[J]. Electromachining & Mould, 2010(2):52-55(in Chinese).
[3] LIU X, KANG X, ZHAO W, et al. Electrode feeding path searching for 5-axis EDM of integral shrouded blisks[C]//The Seventeeth CIRP Conference on Electro Physical and Chemical Machining (ISEM). 2013:107-111.
[4] 崔海军, 张明岐, 程小元. 民机机匣电解加工设备的研制[J]. 电加工与模具, 2016(z1):60-62. CUI H J, ZHANG M Q, CHENG X Y. Development of the ECM machine for civil aeroengine casing[J]. Electromachining & Mould, 2016(z1):60-62(in Chinese).
[5] 任军学, 田卫军, 姚倡锋, 等. 航空发动机机匣数控加工关键技术研究[J]. 航空制造技术, 2016(5):73-77. REN J X, TIAN W J, YAO C F, et al. Research on key technology of aeroengine casing CNC machining[J]. Aeronautical Manufacturing Technology, 2016(5):73-77(in Chinese).
[6] 任军学, 龚仔华, 田荣鑫, 等. 航空发动机机匣五轴插铣加工[J]. 航空制造技术, 2013(9):58-61. REN J X, GONG Z H, TIAN R X, et al. 5-axis plunge milling of aeroengine case[J]. Aeronautical Manufacturing Technology, 2013(9):58-61(in Chinese).
[7] HIRANO C, MORISHIGE K. Development of rough cutting method with plunge milling using 5-axis control machine tool[J]. Journal of the Japan Society for Precision Engineering, 2007, 73(11):1261-1266.
[8] 周续, 张定华, 吴宝海, 等. 材料切除对机匣铣削动力学与稳定性的影响[J]. 航空学报, 2016, 37(4):1352-1362. ZHOU X, ZHANG D H, WU B H, et al. Dynamics and stability analysis in end milling of aero-engine casing considering material removal effect[J]. Acta Aeronautica et Astronautica Sinica, 2016, 37(4):1352-1362(in Chinese).
[9] PATIL P, POLISHETTY A, GOLDBERG M, et al. Slot machining of TI6AL4V with trochoidal milling technique[J]. Journal of Machine Engineering, 2014, 14(4):42-54.
[10] ELBER G, COHEN E, DRAKE S. MATHSM:Medial axis transform toward high speed machining of pockets[J]. Computer-Aided Design, 2005, 37(2):241-250.
[11] XIONG Z H, ZHUANG C G, DING H. Curvilinear tool path generation for pocket machining[J]. Proceedings of the Institution of Mechanical Engineers, Part B:Journal of Engineering Manufacture, 2011, 225(4):483-495.
[12] IBARAKI S, YAMAJI I, MATSUBARA A. On the removal of critical cutting regions by trochoidal grooving[J]. Precision Engineering, 2010, 34(3):467-473.
[13] RAUCH M. Rough pocket milling with trochoidal and plunging strategies[J]. International Journal of Machining & Machinability of Materials, 2007, 2(2):161-175.
[14] RAUCH M, DUC E, HASCOET J Y. Improving trochoidal tool paths generation and implementation using process constraints modelling[J]. International Journal of Machine Tools & Manufacture, 2009, 49(5):375-383.
[15] FERREIRA J C, OCHOA D M. A method for generating trochoidal tool paths for 21/2 D pocket milling;process planning with multiple tools[J]. Proceedings of the Institution of Mechanical Engineers, Part B:Journal of Engineering Manufacture, 2013, 227(9):1287-1298.
[16] DIEHL A, PATTERSON R B. Method of milling an interior region:US8560113[P]. 2013.
[17] SONA G. Automatic method for milling complex channel-shaped cavities:US9423788[P]. 2016.
[18] OTKUR M, LAZOGLU I. Trochoidal milling[J]. International Journal of Machine Tools & Manufacture, 2007, 47(9):1324-1332.
[19] SZALÓKI I, CSUKA S, SIPOS S. New test results in cycloid-forming trochoidal milling[J]. Acta Polytechnica Hungarica, 2014, 11(2):215-228.
[20] KARDES N, ALTINTAS Y. Mechanics and dynamics of the circular milling process[J]. Journal of Manufacturing Science & Engineering, 2007, 129(1):21-31.
[21] KLOCKE F, BERGS T, BUSCH M, et al. Integrated approach for a knowledge-based process layout for simultaneous 5-axis milling of advanced materials[J]. Advances in Tribology, 2011, 2011:108-115.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

航空发动机机匣摆线粗加工轨迹规划方法

A trochoidal path planning method for rough machining of aeroengine casing parts

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	冉庆波, 肖鸿, 杨富鸿, 段玉岗. 含孔曲面自动铺丝轨迹规划算法[J]. 航空学报, 2022, 43(9): 425602-425602.
[2]	孙杨, 昌敏, 白俊强. 微小型四旋翼无人机垂面栖停轨迹规划与控制[J]. 航空学报, 2022, 43(9): 325756-325756.
[3]	徐广通, 王祝, 曹严, 孙景亮, 龙腾. 动态优先级解耦的无人机集群轨迹分布式序列凸规划[J]. 航空学报, 2022, 43(2): 325059-325059.
[4]	孙昊, 孙青林, 滕海山, 周朋, 陈增强. 复杂环境下考虑动力学约束的翼伞轨迹规划[J]. 航空学报, 2021, 42(3): 324301-324301.
[5]	胡军, 李毛毛. 航天器进入制导方法综述[J]. 航空学报, 2021, 42(11): 525048-525048.
[6]	刘哲, 陆浩然, 郑伟, 闻国光, 王奕迪, 周祥. 多滑翔飞行器时间协同轨迹快速规划[J]. 航空学报, 2021, 42(11): 524497-524497.
[7]	邓云山, 夏元清, 孙中奇, 沈刚辉. 扰动环境下火星精确着陆自主轨迹规划方法[J]. 航空学报, 2021, 42(11): 524834-524834.
[8]	葛佳昊, 刘莉, 董欣心, 田维勇, 陆天和. 基于动力学RRT^*的自由漂浮空间机器人轨迹规划[J]. 航空学报, 2021, 42(1): 523877-523877.
[9]	赵毓, 管公顺, 郭继峰, 于晓强, 颜鹏. 基于多智能体强化学习的空间机械臂轨迹规划[J]. 航空学报, 2021, 42(1): 524151-524151.
[10]	戴健, 许菲, 陈琪锋. 多无人机协同搜索区域划分与路径规划[J]. 航空学报, 2020, 41(S1): 723770-723770.
[11]	耿远卓, 李传江, 郭延宁, James Douglas BIGGS. 单推力航天器交会对接轨迹规划及跟踪控制[J]. 航空学报, 2020, 41(9): 323880-323880.
[12]	王晶, 罗明, 张定华, 陈冰. 自由曲面侧铣刀具轮廓与轨迹同步优化方法[J]. 航空学报, 2020, 41(11): 423720-423720.
[13]	宋桂林, 王显峰, 赵聪, 高天成, 薛柯. 规则回转体自动铺丝轨迹规划与丝束增减[J]. 航空学报, 2020, 41(11): 423704-423704.
[14]	周祥, 张洪波, 何睿智, 汤国建, 包为民. 基于凸优化的再入轨迹三维剖面规划方法[J]. 航空学报, 2020, 41(11): 623842-623842.
[15]	邢伯阳, 潘峰, 王位, 冯肖雪. 基于复合地标导航的动平台四旋翼飞行器自主优化降落技术[J]. 航空学报, 2019, 40(6): 322601-322601.