尾迹对涡轮动叶全表面气膜冷却效率的影响

doi:10.7527/S1000-6893.2018.22651

Abstract

Abstract: The effect of unsteady wake on the film cooling effectiveness of the turbine blade is studied using the Pressure Sensitive Paint (PSP) measurement technique. The test blade has eleven rows of cylindrical film holes. The distribution of the film cooling effectiveness on the whole blade surface under different mass flux ratios and different wake Strouhal numbers (Sr=0, 0.12, 0.36) are obtained. The results show that as the wake Strouhal number increases, the radial averaged film cooling effectiveness of the leading edge decreases by up to 36.5%, the radial averaged film cooling effectiveness of the suction surface decreases by up to 53.5%, and that of the pressure surface decreases by up to 24.2%. The effect of wake on the leading edge and the suction surface is greater than that on the pressure surface. As the mass flux ratio increases, the effect of the unsteady wake decreases. When designing the cooling structure of the turbine blade, ignoring the effect of the wake increases the design risk.

Key words: wakes, film cooling effectiveness, PSP technique, mass flux ratio, Strouhal number, turbine blade

CLC Number:

V231.1

CHEN Dawei, ZHU Huiren, LI Huatai, LIU Haiyong, ZHOU Daoen. Effect of unsteady wake on full coverage film cooling effectiveness for a turbine blade[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(3): 122651-122651.

References

[1] FERNANDES C P, VOET M T, LITTLE Z, et al. Flow statistics and visualisation of multi-row film cooling boundary layers:GT2017-64391[R]. New York:ASME, 2017.
[2] 朱惠人, 许都纯, 刘松龄, 等. 簸箕形排孔气膜冷却实验研究[J]. 航空学报, 1997, 18(5):25-28. ZHU H R, XU D C, LIU S L, et al. Film cooling experimental investigation of a row of dust-pan shaped holes[J]. Acta Aeronautica et Astronautica Sinica, 1997, 18(5):25-28(in Chinese).
[3] 韩振兴, 末永洁, 刘石. 吹风比对气膜冷却效率影响的实验研究[J]. 航空学报, 2004, 25(6):551-555. HAN Z X, MO Y J, LIU S. Experimental research on film cooling effectivenesses at different blowing ratios[J]. Acta Aeronautica et Astronautica Sinica, 2004, 25(6):551-555(in Chinese).
[4] 李广超, 张魏, 彭大维, 等. 带锥形扩张支孔射流气膜冷却效率数值模拟[J]. 航空学报, 2010, 31(7):1360-1365. LI G C, ZHANG W, PENG D W, et al. Numerical simulation of film cooling effectiveness with conical expanded branch holes[J]. Acta Aeronautica et Astronautica Sinica, 2010, 31(7):1360-1365(in Chinese).
[5] 游良平, 陶毓伽, 蔡军, 等. 涡轮叶片前缘复合冷却实验[J]. 航空学报, 2009, 30(9):1618-1623. YOU L P, TAO Y J, CAI J, et al. Experiment of composite cooling on leading edge of turbine blade[J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(9):1618-1623(in Chinese).
[6] WIESE C J, RUTLEDGE J L, POLANKA M D. Experimental evaluation of thermal and mass transfer techniques to measure adiabatic effectiveness with various coolant to freestream property ratios:GT2017-65019[R]. New York:ASME, 2017.
[7] MCCLINTIC J W, ANDERSON J B, BOGARD D G, et al. Effect of internal crossflow velocity on film cooling effectiveness-Part I:Axial shaped holes:GT2017-64616[R]. New York:ASME, 2017.
[8] MCCLINTIC J W, ANDERSON J B, BOGARD D G, et al. Effect of internal crossflow velocity on film cooling effectiveness-Part Ⅱ:Compound angle shaped holes:GT2017-64624[R]. New York:ASME, 2017.
[9] 姚玉, 张靖周, 何飞, 等. 涡轮叶片吸力面上收敛缝形孔气膜冷却效率的数值研究[J]. 航空学报, 2010, 31(6):1115-1120. YAO Y, ZHANG J Z, HE F, et al. Numerical investigation on film cooling effectiveness of converging slot hole at turbine blade suction surface[J]. Acta Aeronautica et Astronautica Sinica, 2010, 31(6):1115-1120(in Chinese).
[10] 丁阳, 常海萍, 杜治能. 多排反向射流角气膜冷却特性研究[J]. 航空学报, 2013, 34(11):2472-2481. DING Y, CHANG H P, DU Z N. Investigation on characteristics of multiple rows of opposite lateral ejection angle film cooling[J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(11):2472-2481(in Chinese).
[11] 刘存良, 朱惠人, 白江涛, 等. 涡轮叶片上收缩-扩张形孔排的全表面气膜冷却特性[J]. 航空学报, 2010, 31(4):687-693. LIU C L, ZHU H R, BAI J T, et al. Experimental research on film cooling characteristics of converging-expanding hole rows on turbine blade surface[J]. Acta Aeronautica et Astronautica Sinica, 2010, 31(4):687-693(in Chinese).
[12] SEO H J, LEE J S, LIGRANI P M. Effects of bulk flow pulsations on film cooling from different length injection holes at different blowing ratios:98-GT-192[R]. New York:ASME, 1998.
[13] JUNG I S, LEE J S. Effects of bulk flow pulsations on film cooling from spanwise oriented holes:98-GT-211[R]:New York:ASME, 1998.
[14] LEE J S, JUNG I S. Effect of bulk flow pulsations on film cooling with compound angle holes[J]. International Journal of Heat & Mass Transfer, 2002, 45(1):113-123.
[15] NIKPARTO A, RICE T, SCHOBEIRI M T. Experimental and numerical investigation of heat transfer and film cooling effectiveness of a highly loaded turbine blade under steady and unsteady wake flow condition:GT2017-65012[R]. New York:ASME, 2017.
[16] LU X G, ZHANG Y F, LI W, et al. Effects of periodic wakes on boundary layer development on an ultra-high-lift low pressure turbine airfoil[J]. Proceedings of the Institution of Mechanical Engineers Part A-Journal of Power & Energy, 2016, 231(1):25-38.
[17] 蒋雪辉, 赵晓路. 非定常尾迹对叶栅气膜冷却效率的影响[J]. 推进技术, 2004, 25(4):311-315. JIANG X H, ZHAO X L. Effect of unsteady wake on linear cascade film cooling efficiency[J]. Journal of Propulsion Technology, 2004, 25(4):311-315(in Chinese).
[18] 蒋雪辉, 赵晓路. 非定常尾迹对气膜冷却影响的数值研究[J]. 工程热物理学报, 2005, 26(2):322-324. JIANG X H, ZHAO X L. Numerical simulation of the unsteady wakes effects on film cooling[J]. Journal of Engineering Thermophysics, 2005, 26(2):322-324(in Chinese).
[19] 蒋雪辉, 赵晓路. 非定常尾迹对叶片头部气膜冷却的影响[J]. 航空动力学报, 2005, 20(4):540-544. JIANG X H, ZHAO X L. The effect of unsteady wake on leading edge film cooling[J]. Journal of Aerospace Power, 2005, 20(4):540-544(in Chinese).
[20] GUENETTE G R, EPSTEIN A H, GILES M B, et al. Fully scaled transonic turbine rotor heat transfer measurements[J]. Journal of Turbomachinery, 1989, 111(1):1-7.
[21] BRIEN J E, CAPP S P. Two-component phase-averaged turbulence statistics downstream of a rotating spoked-wheel wake generator[J]. Journal of Turbomachinery, 1989, 111(4):475-482.

Effect of unsteady wake on full coverage film cooling effectiveness for a turbine blade

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	FAN Yongsheng, YANG Xiaoguang, SHI Duoqi, TAN Long, HUANG Weiqing. Rafting-waste judgement of serviced turbine blades: quantitative characterization and threshold determination [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(9): 625100-625100.
[2]	LI Dichen, LU Zhongliang, TIAN Xiaoyong, ZHANG Hang, YANG Chuncheng, CAO Yi, MIAO Kai. Additive manufacturing—Revolutionary technology for leading aerospace manufacturing [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525387-525387.
[3]	JIA Yuchao, CHI Guanxin, ZHANG Kun, ZHANG Jia, WANG Zhenlong. High-efficiency electrical arc machining of integral shrouded blisk using grouped electrode [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525605-525605.
[4]	ZHANG Peiyu, ZHOU Xin, LI Yinghong. Progress on high energy beam repair of single crystal turbine blades [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525610-525610.
[5]	WANG Bin, WANG Haitao, WANG Yufeng, ZHANG Wenwu. Water-assisted laser scanning machining test of thermal barrier coating [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525353-525353.
[6]	YE Lin, LIU Cunliang, ZHU Andong, ZHOU Tianliang. Influence of compact-ribbed passage on trailing-edge cutback film cooling performance [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(3): 125174-125174.
[7]	LEI Shiying, SUN Jianzhong, LIU He. Cumulative damage index model and service reliability evaluation of turbine blade [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(3): 225064-225064.
[8]	WANG Maosong, DU Yulei. Research progress of additive manufacturing of TiAl alloys [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(7): 625263-625263.
[9]	WANG Jin, SUN Jie, ZHAO Zhanming, ZHANG Bo, REN Xiaodong, XIE Gongnan. Research on film cooling performance of sister hole based on structural parameter analysis [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(7): 124775-124775.
[10]	HU Xiaoan, SHI Duoqi, YANG Xiaoguang, YU Huichen. TMF constitutive and life modeling: From smooth specimen to turbine blade [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(3): 422494-422494.
[11]	HUANG Fuxiang, MIAO Kai, LU Zhongliang, XU Wenliang, ZHU Weijun, LI Dichen. Effects of radiation coatings on directional solidification microstructure of hollow turbine blades [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(3): 421462-421462.
[12]	CUI Kang, WANG Wenhu, JIANG Ruisong, ZHAO Dezhong, JIN Qichao. Force-constraint method for localization of ceramic core of hollow turbine blade [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(9): 421209-421209.
[13]	YANG Xiaojun, ZHU Jiaxiong. Numerical simulation of particle deposition process inside turbine cascade [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(5): 120530-120530.
[14]	ZHOU Junhui, ZHANG Jingzhou. Effects of partial blockage inside film holes on overall cooling effectiveness of an integrated impingement-fin-film cooling configuration on blade pressure side [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2016, 37(9): 2729-2738.
[15]	GUO Wei, DONG Lihong, WANG Huipeng, XU Binshi. Research progress of damage estimation for turbine blades based on infrared thermographic technology [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2016, 37(2): 429-436.