轴承腔内壁与油膜换热的数值模拟与试验

doi:10.7527/S1000-6893.2017.621013

Abstract

Abstract:

It is necessary to analyze heat transfer between the lubricating oil and the inner wall of the rear bearing chamber in the design of the heat protection structure for an aero-engine. The characteristics of the influence of the inner wall heat transfer from the oil film is obtained through both experiments and numerical simulation. The temperature distribution of the outer wall, inner wall and the oil film is tested to calculate the heat flux and the transfer coefficient. The simulation of the test rig is carried out using fluid-structure coupling with heat transfer, and the CLSVOF (Coupled Level Set and Volume Of Fluid) model is adopted to simulate the gas/oil flow. Comparisons of the local heat flux are then made between the experiments and the numerical simulation under different conditions, and the results show that the simulation results agree well with the experiment data. The relation between the heat coefficient and the local oil film Reynolds number Re_l is also discussed. The local Nusselt number Nu_w near the wall is directly proportional to 0.7 power of local Reynolds number Re_l. In addition, analysis of the influence of the rotating speed shows that Nu_w is proportional to 0.345 power of the rotary shaft rotational Reynolds number Re_rot.

Key words: aero-engine, rear bearing chamber, heat transfer, lubricating oil film, experimental study, numerical simulation

CLC Number:

V233.4

HU Jianping, REN Guozhe, YI Jun, LIU Zhenxia, LYU Yaguo, ZHAO Jingyu. Numerical simulation and experiment for heat transfer between oil film and inner wall of bearing chamber[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(9): 521013-521013.

References

[1] KLINGSPORN M. Advanced transmission and oil system concepts for modern aero-engines:GT2004-53578[R]. New York:ASME, 2004.
[2] 葛治美, 韩振兴, 张恩和, 等. 航空发动机轴承腔热分析计算[J]. 航空动力学报, 2005, 20(3):483-486. GE Z M, HAN Z X, ZHANG E H, et al. Thermal analysis of aeroengine bearing compartment[J]. Journal of Aerospace Power, 2005, 20(3):483-486(in Chinese).
[3] MICHAEL F. Analytical and numerical simulations of the two-phase flow heat transfer in the vent and scavenge pipes of the CLEAN engine demonstrator[J]. Journal of Turbomachinery, 2010, 132:011008.
[4] GLAHN A, WITTIG S. Two-phase air/oil flow in aero engine bearing chambers:Characterization of oil film flows[J]. Journal of Engineering for Gas Turbines and Power, 1996, 118(3):578-583.
[5] BAI C X, GOSMAN A D. Development of methodology for spray impingement simulation:SAE 950283[R]. Warrendale, PA:SAE International, 1995.
[6] FARRALL M, HIBBERD S, SIMMONS K. The effect of initial injection conditions on the oil droplet motion in a simplified bearing chamber[J]. Journal of Engineering for Gas Turbines and Power, 2008,130(1):12501-12507.
[7] SIMMONS K. Numerical study of the two-phase air/oil flow within an aero-engine bearing chamber model using a coupled Lagrangian droplet tracking method[C]//ASME 2002 Pressure Vessels and Piping Conference. New York:ASME, 2002:325-331.
[8] WOLFRAM K, KLAUS D, HANS J B. Influence on the oil split between the offtakes of an aero-engine bearing chamber:GT2012-69412[R]. New York:ASME, 2012.
[9] WITTIG S, GLAHN A, HIMMELSBACH J. Influence of high rotational speeds on heat transfer and oil film thickness in aero-engine bearing chambers[J]. Journal of Engineering for Gas Turbines and Power, 1994, 116(2):395-401.
[10] GLAHN A, BUSAM S, WITTING S. Local and mean heat transfer coefficients along the internal housing walls of aero engine bearing chambers:GT1997-0261[R]. New York:ASME, 1997.
[11] BUSAM S, GLAHN A, WITTIG S. Internal bearing chamber wall heat transfer as a function of operating conditions and chamber geometry[J]. Journal of Engineering for Gas Turbines and Power, 2000, 122(2):314-320.
[12] 陈薄, 陈国定, 王涛. 考虑油滴变形和二次油滴效应的轴承腔壁面油膜流动分析[J]. 航空学报, 2013, 34(8):1980-1989. CHEN B, CHEN G D, WANG T. Flow characteristics analysis of wall oil film with consideration of oil droplet deformation and secondary oil droplet deposition in aeroengine bearing chamber[J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(8):1980-1989(in Chinese).
[13] 吕亚国, 张美华, 刘振侠, 等. 航空发动机轴承腔油气两相流流动数值研究及验证[J]. 航空动力学报, 2014, 29(11):2751-2757. LV Y G, ZHANG M H, LIU Z X, et al. Numerical study and validation for two-phase flow of oil and gas in aero-engine bearing cavity[J]. Journal of Aerospace Power, 2014, 29(11):2751-2757(in Chinese).
[14] CHONG Z, HU J P, LIU Z X, et al. Application of the ultrasonic oil film thickness measurement system in bearing chambers[J]. International Journal of Turo & Jet-Engines, 2013, 32(2):159-165.
[15] 刘振侠, 黄生勤, 吕亚国, 等. 航空发动机润滑系统通用分析软件开发[J]. 航空动力学报, 2007, 22(1):12-17. LIU Z X, HUANG S Q, LV Y G, et al. General analysis software of aeroengine lubrication system design[J]. Journal of Aerospace Power, 2007, 22(1):12-17(in Chinese).
[16] GLAHN A, KURRECK M, WILLMANN M, et al. Feasibility study on oil droplet flow investigations inside aero engine bearing chambers-PDPA technique in combination with numerical approaches[J]. Journal of Engineering for Gas Turbines and Power, 1996, 118(4):749-755.
[17] LIU Z X, ZHAO J Y, HU J P, et al. A numerical model for unsteady oil film motion in aero-engine bearing chamber and experimental verification:GTINDIA 2013-3639[R]. New York:ASME, 2013.
[18] CHANG Y C, HOU T Y,MERRIMAN B, et al. A level set formulation of eulerian interface capturing methods for incompressible fluid flows[J]. Journal of Computational Physics, 1996, 124(2):449-464.
[19] CHANDRA B, SIMMONS K, PICKERING S, et al. Factors affecting oil removal from an aeroengine bearing chamber:GT2010-22631[R]. New York:ASME, 2010.
[20] ZHAO J Y, LIU Z X. Numerical and experimental study for unsteady oil film thickness of the rotating cylinder chamber wall[J]. Journal of Engineering for Gas Turbines and Power, 2015, 137(12):122501.
[21] 任国哲, 刘振侠, 赵静宇, 等. 基于DPM与VOF方法轴承腔内滑油瞬态特性[J]. 航空计算技术, 2016, 46(1):11-15. REN G Z, LIU Z X, ZHAO J Y, et al. Motion of wall oil film with consideration of oil-gas coupled heat and mass transfer in bearing chamber[J]. Aeronautical Computing Technique, 2016, 46(1):11-15(in Chinese).
[22] 郝毓雅, 孙嘉琪, 刘振侠, 等. 轴承腔壁面液膜厚度测量系统的设计与实现[J]. 航空计算技术, 2012, 42(6):121-124. HAO Y Y, SUN J Q, LIU Z X, et al. Design and realization of measuring system for film thickness in bearing chamber[J]. Aeronautical Computing Technique, 2012, 42(6):121-124(in Chinese).

Numerical simulation and experiment for heat transfer between oil film and inner wall of bearing chamber

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Chang WANG, Long HE, Dongxia XU, Min TANG, Shuai MA, Ximing WU. Flow control drag reduction of hub on coaxial rigid rotor aircraft [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(9): 529084-529084.
[2]	Zeyong YIN, Gaiqi LI, Jiancheng SHI, Yueqian YIN. Concept, method and practice of advanced versatile core engine derivative [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(7): 29713-029713.
[3]	Weina HUANG, Fangjuan LI, Hongbin QI. Preliminary investigation and thoughts on aero-engine digital engineering development [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(5): 529693-529693.
[4]	Ruixian MA, Xin WANG, Kaiming WANG, Bin LI, Mingfu LIAO, Siji WANG. Rubbing experimental study on labyrinth and rubber⁃coated case for aero⁃engines [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(4): 628350-628350.
[5]	Yuan XIAO, Kun FENG, Minghui HU, Zhinong JIANG. Extraction method for unsteady vibration components of aero-engine rotors [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(3): 228158-228158.
[6]	Hong WEI, Peng WANG, Wei DONG, Xiaofeng GUO, Zhida LI, Xuesen YANG, Zhongfu TANG, Chao FU. Effects of main flow velocity on frosting and defrosting characteristics of microtubule precooler [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(2): 128639-128639.
[7]	Jiang LAI, Zhaolin FAN, Qian WANG, Siwei DONG, Fulin TONG, Xianxu YUAN. Direct numerical simulation of hypersonic cone-flare model at angle of attack [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(2): 128610-128610.
[8]	Yingjiao HU, Feng XU, Zhijun YANG. Overview of aero-engine ice testing capability [J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(S2): 729449-729449.
[9]	Hongjian ZHANG, Yanxin ZHANG, Jianjun XIONG, Zhao ZHAO, Lin RAN, Xian YI. Numerical simulation of phased array ultrasonic beam propagation characteristics in ice layer [J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(S2): 729289-729289.
[10]	Yalu FU, Xianxu YUAN, Pengxin LIU, Ming YU. Statistical properties of thermodynamic fluctuations in compressible wall⁃bounded turbulence [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2023, 44(9): 127217-127217.
[11]	Neng WAN, Qixin ZHUANG, Yanheng GUO, Zhiyong CHANG, Dao WANG. Sampling strategy for on-machine measurement of aero-engine blade under constraint of fitting accuracy [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2023, 44(7): 427151-427151.
[12]	Rong HAN, Wei LIU, Xiaoliang YANG. Dynamic drag reduction mechanism of self-aligned aerodisks on hypersonic aircraft [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2023, 44(4): 126633-126633.
[13]	Pinpeng ZENG, Shusheng CHEN, Jinping LI, Muliang JIA, Zhenghong GAO. Numerical simulation of heat reduction on blunt-headed bodies by combined scheme of drag reduction spike and annular jets [J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(22): 128407-128407.
[14]	Fenfen XIONG, Zexian LI, Yu LIU, Tangfan XIAHOU. A review of characterization methods for parameter uncertainty in engineering design based on numerical simulation [J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(22): 28611-028611.
[15]	Yunlong ZHENG, Peiqing LIU, Qiulin QU, Jiahua DAI, Yu TIAN. Numerical investigation on motion characteristics of BWB aircraft in ditching [J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(21): 528588-528588.