基于包络理论的刀位误差快速求解算法

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

基于包络理论的刀位误差快速求解算法

颜家勇, 陈志同, 贺英

北京航空航天大学机械工程及自动化学院, 北京 100191

收稿日期:2011-01-25 修回日期:2011-02-18 出版日期:2011-11-25 发布日期:2011-11-24
通讯作者: 陈志同 E-mail:ztchen@buaa.edu.cn
作者简介:颜家勇(1985- ) 男,硕士研究生。主要研究方向:五坐标数控加工编程技术。 Tel: 010-82339151 E-mail: yanjiayong0713@126.com 陈志同(1967- ) 男,博士,教授,博士生导师。主要研究方向:五坐标数控加工编程技术,数控加工过程参数优化。 Tel: 010-82339151 E-mail: ztchen@buaa.edu.cn 贺英(1986- ) 男,硕士研究生。主要研究方向:五坐标数控加工编程技术。 Tel: 010-82339151 E-mail: hybuaa@163.com
基金资助:
国家自然科学基金 (50875012);国家科技重大专项(2009ZX04001-141)

A Quick Calculation Method of Tool Position Error Based on Envelope Theory

YAN Jiayong, CHEN Zhitong, HE Ying

School of Mechanical Engineering and Automation, Beihang University, Beijing 100191, China

Received:2011-01-25 Revised:2011-02-18 Online:2011-11-25 Published:2011-11-24

摘要/Abstract

摘要： 针对五坐标数控加工中刀位误差计算效率较低的问题,提出了一种基于包络原理的刀位误差快速计算方法。首先,通过描述刀位误差与最短距离线段的关系建立两者的关系式。其次,将工件曲面沿进给方向离散成若干条截型线,基于包络原理推导出工件曲面截型线到刀具曲面的距离最短点应满足的基本方程,通过求解该方程获得最短距离线段和刀位误差,建立误差分布曲线。最后,分析了W形和V形误差分布曲线的特点,对曲面截型线离散精度的确定方法进行了研究。在此基础上,设计了计算流程,开发了计算程序,算例结果表明:所提方法与原方法相比,计算效率有了很大的提高。

关键词: 刀位误差, 复杂曲面, 数控加工, 最短距离线对, 包络原理

Abstract: In order to improve the low calculation efficiency of tool position error in the programming of 5-axis numerical control (NC) machining, a quick calculation method of tool position error based on envelope theory is proposed. First, a relationship equation is established between the shortest distance line and the tool position error. Then, the workpiece surface is discretized into a number of sectional curves along the feed direction. With the tangent condition of the envelope theory, another basic equation is presented to calculate the shortest distances between the tool surface and the workpiece surface sectional curves. The shortest distance line and tool position error can be obtained through the equation. Then the error distribution curves can be established. Finally, the problem of surface sectional curve discretization is studied through analyzing the characteristics of different error distribution curves. On this basis, calculation flows are designed, and programs developed. Calculation examples are given in this paper in which the calculation efficiency of the new method is compared with that of the previous method. It is shown that the new method can greatly improve the calculation efficiency of the shortest distance pair.

Key words: tool position error, sculptured surface, NC machining, the shortest distance pair, envelope theory

中图分类号:

TP391.72

颜家勇, 陈志同, 贺英. 基于包络理论的刀位误差快速求解算法[J]. 航空学报, 2011, 32(11): 2131-2139.

YAN Jiayong, CHEN Zhitong, HE Ying. A Quick Calculation Method of Tool Position Error Based on Envelope Theory[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2011, 32(11): 2131-2139.

参考文献

[1] Vickers G W, Bedi S, Haw R. The definition and manufacture of compound curvature surfaces using G-surf[J]. Computers in Industry, 1985, 6(3): 173-183.

[2] Vickers G. Quan K. Ball-mills versus end-mills for curved surface machining[J]. ASME Journal of Engineering for Industry, 1989, 111(2): 22-26.

[3] Madhavulu G, Anil S S, Ahmed B. CAD/CAM solutions for efficient machining of turbo machinery components Sturz milling method//Proceedings of the 1996 IEEE IECON 22nd International Conference. Taipei: IEEE, 1996.

[4] Jensen C G, Anderson D C. Accurate tool placement and orientation for finish surface machining[J]. American Society of Mechanical Engineers, 1992, 59: 127-145.

[5] Lee Y S. Admissible tool orientation control of gouging avoidance for 5-axis complex surface machining[J]. Computer-Aided Design, 1997, 29(7): 507-521.

[6] 陈涛, 钟毅芳, 周济. 自由曲面5轴数控加工刀位轨迹的生成算法[J]. 机械工程学报, 2001, 37(12): 100-103. Chen Tao, Zhong Yifang, Zhou Ji. Algorithm of cutter location path grneration for 5-axis NC machining of sculptured surfaces[J]. Chinese Journal of Mechanical Engineering, 2001, 37(12): 100-103. (in Chinese)

[7] Lasemi A, Xue D Y, Gu P H. Recent development in CNC machining of freeform surfaces: a state-of-the-art review[J]. Computer-Aided Design, 2010, 42(7): 641-654.

[8] 朱利民, 丁汉, 熊有伦. 非球头刀宽行五轴数控加工自由曲面的三阶切触法(I): 刀具包络曲面的局部重建原理[J]. 中国科学:技术科学, 2010, 40(11): 1268-1275. Zhu Limin, Ding Han, Xiong Youlun. Third-order point contact approach for 5-axis sculptured surface machining using non-ball-end tools(I): Third-order approximation of envelope surface[J]. Science in China: Technological Sciences, 2010, 40(11): 1268-1275. (in Chinese)

[9] 倪炎榕. 环面刀具五坐标数控加工复杂曲面优化刀位计算与图形显示. 北京:北京航空航天大学机械工程及自动化学院,1999. Ni Yanrong. Optimal tool location calculation of sculpture surface and its graphics display in 5-axis NC machining with tours cutter. Beijing: School of Mechanical Engineering and Automation, Beihang University, 1999. (in Chinese)

[10] 徐汝锋. 宽行加工刀位误差求解与刀轨规划技术研究. 北京:北京航空航天大学机械工程及自动化学院,2010. Xu Rufeng. Research on tool position error calculation and tool path planning methods in 5-axis machining of sculptured surfaces. Beijing: School of Mechanical Engineering and Automation, Beihang University, 2010. (in Chinese)

[11] 徐汝锋, 陈五一, 陈志同. 基于经线划分的非圆截面环形刀具刀位优化算法[J]. 航空学报,2010, 31(2): 410-417. Xu Rufeng, Chen Wuyi, Chen Zhitong. A tool positioning algorithm through longitude separation approach for a cutter with non-circle generatrix[J]. Acta Aeronoutica et Astronautica Sinica, 2010, 31(2): 410-417. (in Chinese)

[12] 李正强, 陈志同, 肖俊. 鼓形刀宽行刀位优化纬线分割算法[J]. 北京航空航天大学学报,2007, 33(6): 731-735. Li Zhengqiang, Chen Zhitong, Xiao Jun. Latitude distribution algorithm of cutter positionoptimization on drum-like cutter for strip-maximization[J]. Journal of Beijing University of Aeronautics and Astronautics, 2007, 33(6): 731-735. (in Chinese)

[13] 倪炎榕, 马登哲, 张洪, 等. 圆环面刀具五坐标数控加工复杂曲面优化刀位算法[J]. 机械工程学报,2001, 37(2): 87-91. Ni Yanrong, Ma Dengzhe, Zhang Hong, et al. Optimal orientation control for torus tool 5-axis sculptured surface NC machining[J]. Chinese Journal of Mechanical Engineering, 2001, 37(2): 87-91. (in Chinese)

[14] 陈丽萍, 陈燕, 胡德金. 一种快速完备的自由曲线和曲面间最短距离求取算法[J]. 上海交通大学学报, 2003, 37(S2): 41-44. Chen Liping, Chen Yan, Hu Dejin. A high-efficiency algorithm to calculate the shortest distance between free-form curve and free-form surface[J]. Journal of Shanghai Jiaotong University, 2003, 37(S2): 41-44. (in Chinese)

[15] 龚堰珏, 贠敏, 王小椿. 自由曲线曲面距离迭代算法的研究及其可视化处理[J]. 小型微型计算机系统, 2003, 24(12): 2306-2308. Gong Yanjue, Yun Min, Wang Xiaochun. Iterative algorithm of distance between free curve and surface and its visualization[J]. Mini-Micro Systems, 2003, 24(12): 2306-2308. (in Chinese)

[16] Chiou C J, Lee Y S. A shape-generating approach for multi-axis machining G-buffer models[J]. Computer-Aided Design, 1999, 31(12): 761-776.

[17] Engeli M, Waldvogel J, Schnider T. Method for processing work pieces by removing material, USA: US 6485236 B1. 2001-11-26.

[18] Warkentin A, Ismail F, Bedi S. Comparison between multipoint and other five-axis tool positioning strategies[J]. Machining Tool & Manufacture, 2000, 40(2): 185-208.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

基于包络理论的刀位误差快速求解算法

A Quick Calculation Method of Tool Position Error Based on Envelope Theory

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	刘占, 张俊, 尹佳, 赵万华. 基于机器视觉的立铣刀几何与状态参数在机检测[J]. 航空学报, 2022, 43(7): 425593-425593.
[2]	吴宝海, 张阳, 郑志阳, 张莹, 张思琪. 数控加工进给速度参数优化研究现状与展望[J]. 航空学报, 2022, 43(4): 525467-525467.
[3]	徐金亭, 牛金波, 陈满森, 孙玉文. 精密复杂曲面零件多轴数控加工技术研究进展[J]. 航空学报, 2021, 42(10): 524867-524867.
[4]	徐超, 胡皓, 彭小强, 李信磊, 林之凡. 复杂曲面铝反射镜磁流变抛光工艺优化[J]. 航空学报, 2021, 42(10): 524914-524914.
[5]	高航, 袁业民, 陈建锋, 王宣平. 航空发动机整体叶盘磨料水射流开坯加工技术研究进展[J]. 航空学报, 2020, 41(2): 623319-623319.
[6]	黄云, 肖贵坚, 邹莱. 整体叶盘抛光技术的研究现状及发展趋势[J]. 航空学报, 2016, 37(7): 2045-2064.
[7]	孟凡军, 陈志同, 宁涛, 徐汝锋. 基于纬线法的鼓形刀具刀位误差分布计算[J]. 航空学报, 2015, 36(12): 4014-4024.
[8]	段玉岗, 董肖伟, 葛衍明, 刘德宁. 基于CATIA生成数控加工路径的机器人纤维铺放轨迹规划[J]. 航空学报, 2014, 35(9): 2632-2640.
[9]	董雷, 曹利新. 通道曲面的柱面逼近方法及其在叶轮插铣中的应用[J]. 航空学报, 2014, 35(8): 2331-2340.
[10]	石巍, 宁涛, 陈志同. 环面工具加工叶根过渡曲面的刀位可行域[J]. 航空学报, 2014, 35(12): 3470-3479.
[11]	王晶, 张定华, 罗明, 吴宝海. 复杂曲面零件五轴加工刀轴整体优化方法[J]. 航空学报, 2013, 34(6): 1452-1462.
[12]	任军学, 杨大望, 姚倡锋, 田荣鑫, 谢志丰. 基于控制线的开式整体叶盘叶片四轴数控加工刀轴控制方法[J]. 航空学报, 2012, 33(8): 1515-1523.
[13]	任军学, 何卿功, 姚倡锋, 梁永收, 刘博. 闭式整体叶盘通道五坐标分行定轴加工刀轴矢量规划方法[J]. 航空学报, 2012, 33(10): 1923-1930.
[14]	徐汝锋;陈五一;陈志同. 基于经线划分的非圆截面环形刀具刀位优化算法[J]. 航空学报, 2010, 31(2): 410-417.
[15]	吴宝海;王尚锦. 自由曲面叶轮的四坐标数控加工研究[J]. 航空学报, 2007, 28(4): 993-998.