航空学报 > 2026, Vol. 47 Issue (19): 133151-133151   doi: 10.7527/S1000-6893.2026.33151

类矩形转圆形内转式进气道流向涡的生成与演化

谌业祺, 洪雨婷, 闫波, 黄琪, 李祝飞()   

  1. 中国科学技术大学 近代力学系,合肥 230027
  • 收稿日期:2025-11-27 修回日期:2025-12-26 接受日期:2026-03-10 出版日期:2026-03-17 发布日期:2026-03-16
  • 通讯作者: 李祝飞 E-mail:lizhufei@ustc.edu.cn
  • 基金资助:
    国家自然科学基金(12172354);国家自然科学基金(12388101);国家自然科学基金(U21B6003);中国科学院基础与交叉前沿科研先导专项(XDB0620201)

Formation and evolution of streamwise vortices in a rectangular-like to circular shape transition inward turning inlet

Yeqi CHEN, Yuting HONG, Bo YAN, Qi HUANG, Zhufei LI()   

  1. Department of Modern Mechanics,University of Science and Technology of China,Hefei 230027,China
  • Received:2025-11-27 Revised:2025-12-26 Accepted:2026-03-10 Online:2026-03-17 Published:2026-03-16
  • Contact: Zhufei LI E-mail:lizhufei@ustc.edu.cn
  • Supported by:
    National Natural Science Foundation of China(12172354);Strategic Priority Research Program of the Chinese Academy of Sciences(XDB0620201)

摘要:

针对类矩形转圆形进气道在来流马赫数为6条件下的复杂流动问题,采用数值模拟与类层析式平面激光散射试验相结合的方法,基于Liutex涡识别准则,研究进气道内流向涡的生成与演化机制,并分析尖/钝前缘和有/无抽吸缝对流向涡的影响。结果表明尖前缘-有抽吸进气道中,唇口激波依次扫掠唇口板与侧壁边界层,诱导生成两处角涡,二者在喉道下游隔离段内逐渐融合成强度更大的流向涡。对于钝前缘进气道而言,后掠钝前缘处产生的有旋气流会在外压缩段壁面拐角处汇聚形成角涡,并在对称面处汇聚形成大尺度流向涡对;在内压缩段,唇口激波先扫掠角涡处的低能流,然后入射至上游已形成的流向涡对,这种复杂激波干扰诱导出与上游流向涡旋转方向相反的新流向涡;在喉道下游,角涡未发生融合,而是与流向涡对共同主导隔离段内的流动。钝前缘-有/无抽吸进气道中的流向涡结构与强度基本一致,表明在内压缩段中设置抽吸缝对钝前缘进气道流场均匀性的影响较小。与尖前缘进气道相比,钝前缘进气道因外压缩段流向涡对的影响,隔离段内流向涡的最大Liutex涡通量减小26.2%,出口总压恢复系数降低9.0%。在设计与评估进气道性能时,应重视前缘钝化的影响,其流动控制策略需着力抑制外压缩段流向涡对。

关键词: 内转式进气道, 钝前缘, 抽吸, 流向涡, 平面激光散射

Abstract:

The complex flow field in a rectangular-like to circular shape transition inlet is investigated to reveal the formation and evolution mechanisms of streamwise vortices. Numerical simulations combined with tomography-like planar laser scattering are conducted at a Mach number of 6. The effects of the sharp/blunt leading edges and with/without suction are also investigated based on Liutex vortex identification method. The results show that in the inlet with sharp leading edge and suction, the cowl shock sweeps the boundary layer on the cowl wall and the sidewall, inducing two corner vortices in turn, which gradually merge into a stronger streamwise vortex in the isolator. In the inlet with blunt leading edge and suction, the rotational flow generated from the swept blunt leading edge converges at the corners of the external compression section to form corner vortices, while also converging near the symmetry plane to form a large-scale counterrotating vortex pair. In the internal compression section, the cowl shock first sweeps the low-momentum flow rolled-up by the corner vortex, and then incident on the upstream counterrotating vortex pair, which induces new streamwise vortices with the opposite direction of rotation to that of the upstream vortices. In isolator, the corner vortices and the counterrotating vortex pair dominates the flow without merging. The structure and strength of the streamwise vortices in the inlet with blunt leading edge and with/without suction are basically the same, indicating that the suction in the internal compression section has few effects on the flow field uniformity in the inlet with blunt leading edge. Due to the influence of the counterrotating vortex pair in the external compression section, the inlet with blunt leading edge exhibits a 26.2% decrease in the maximum Liutex vortex flux of the streamwise vortices in the isolator and a 9.0% decrease in the total pressure recovery coefficient on the exit compared to the inlet with sharp leading edge. The effect of the bluntness of the leading edge should be emphasized when designing and evaluating the performance of an inlet. The corresponding flow control strategy should focus on suppressing the counterrotating vortex pairs derived from the external compression section.

Key words: inward turning inlet, blunt leading edge, suction, streamwise vortices, planar laser scattering

中图分类号: