扫描振镜激光TC4钛合金焊接性能及熔池流动行为

doi:10.7527/S1000-6893.2021.25223

论文

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

扫描振镜激光TC4钛合金焊接性能及熔池流动行为

陈波^1,2, 孟正¹, 马程远¹, 席鑫¹, 王昕欣³, 檀财旺^1,2, 宋晓国^1,2

1. 哈尔滨工业大学(威海)山东省特种焊接技术重点实验室, 威海 264209;
2. 哈尔滨工业大学先进焊接与连接国家重点实验室, 哈尔滨 150001;
3. 伦敦大学学院机械工程系, 伦敦 SW75 NP

收稿日期:2021-01-06 修回日期:2021-01-19 发布日期:2021-03-26
通讯作者: 陈波 E-mail:chenbo@hitwh.edu.cn
基金资助:
国家重点研发计划（2018YFB1107900）

Welding properties and molten pool flow behavior of TC4 titanium alloy by oscillating galvanometer laser

CHEN Bo^1,2, MENG Zheng¹, MA Chengyuan¹, XI Xin¹, WANG Xinxin³, TAN Caiwang^1,2, SONG Xiaoguo^1,2

1. Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology, Weihai, Weihai 264209, China;
2. State Key Laboratory of Advanced Welding and Connection, Harbin Institute of Technology, Harbin 150001, China;
3. Department of Mechanical Engineering, University College London, London SW75 NP, United Kingdom

Received:2021-01-06 Revised:2021-01-19 Published:2021-03-26
Supported by:
National Key Research and Development Program (2018YFB1107900)

摘要/Abstract

摘要： 钛合金广泛应用于飞行器及航空航天发动机，激光焊是连接钛合金的优异焊接方法，目前主要问题是气孔导致的接头性能降低。扫描激光能显著改善激光焊接过程中的匙孔行为及熔池流动状态，从而降低气孔率、细化晶粒，最终提高接头性能。采用光纤激光器对4 mm厚TC4钛合金进行扫描振镜激光焊接，对比分析了以0.4 mm为步长、0.4~1.6 mm扫描幅度扫描前后的焊缝成形、力学性能、晶粒细化程度、熔池流动与匙孔行为。结果表明圆形扫描路径下，激光功率为4 kW、焊接速度为1.2 m/min、离焦量为0、扫描频率为100 Hz、扫描幅度为0.8 mm时，匙孔型气孔受显著抑制，且对应的接头抗拉强度最高，为1 025.03 MPa，达到了母材的96%。与无扫描光束相比较，扫描幅度为0.8 mm的接头上部平均晶粒面积减小了65%；圆形扫描的加入使熔池流动具有方向性，同时扫描激光能扩大并稳定匙孔，减少飞溅与气孔。

关键词: 激光焊接, 扫描激光, 力学性能, 晶粒细化, 熔池流动, 钛合金

Abstract: Titanium alloys are widely used in aircraft and aerospace engines. Laser welding is an excellent welding method for joining titanium alloys, and the main problem currently existing is the degradation of joint performance due to porosity. Oscillating laser can significantly improve the keyhole behavior and molten pool flow state, thereby reducing porosity and refining grains, and eventually improving the joint properties in laser welding. Fiber laser was used to join the 4 mm thick TC4 titanium alloy using oscillating laser welding, and the weld formation, mechanical properties, grain refinement, molten pool flow and keyhole behavior before and after oscillating by 0.4 mm steps from 0.4 mm to 1.6 mm oscillating amplitude were compared and analyzed. The results show that keyhole-induced pores were significantly suppressed at a laser power of 4 kW, welding speed of 1.2 m/min, off-focus amount of 0, oscillating frequency of 100 Hz and oscillating amplitude of 0.8 mm, and the joint obtained can achieve the highest tensile strength of 1 025.03 MPa, which is 96% of that of the base material. Compared to the beam without laser oscillating, the upper grains of the joint with an oscillating amplitude of 0.8 mm were refined by 65%. The presence of circular laser oscillating caused the molten pool to be more stable, and gave directionality to the molten pool flow while the oscillating laser enlarged and stabilized the keyhole, reducing spatter and porosity.

Key words: laser welding, oscillating laser welding, mechanical property, grain refinement, molten pool flow, titanium alloy

中图分类号:

V252.2

陈波, 孟正, 马程远, 席鑫, 王昕欣, 檀财旺, 宋晓国. 扫描振镜激光TC4钛合金焊接性能及熔池流动行为[J]. 航空学报, 2022, 43(4): 525223-525223.

CHEN Bo, MENG Zheng, MA Chengyuan, XI Xin, WANG Xinxin, TAN Caiwang, SONG Xiaoguo. Welding properties and molten pool flow behavior of TC4 titanium alloy by oscillating galvanometer laser[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525223-525223.

参考文献

[1] LU K. Materials science. The future of metals[J]. Science, 2010, 328(5976):319-320.
[2] 刘世锋, 宋玺, 薛彤, 等. 钛合金及钛基复合材料在航空航天的应用和发展[J]. 航空材料学报, 2020, 40(3):77-94. LIU S F, SONG X, XUE T, et al. Application and development of titanium alloy and titanium matrix composites in aerospace field[J]. Journal of Aeronautical Materials, 2020, 40(3):77-94(in Chinese).
[3] 孙建刚, 高福洋, 高奇, 等. TC4钛合金热丝钨极氩弧焊接头组织性能研究[J]. 材料开发与应用, 2019, 34(2):9-13. SUN J G, GAO F Y, GAO Q, et al. Study on microstructure and properties of hot-wire-TIG welded joint of TC4 titanium alloy[J]. Development and Application of Materials, 2019, 34(2):9-13(in Chinese).
[4] 招文龙, 刘小刚, 谢佩玉, 等. TC4钛合金扩散焊接头剪切疲劳性能研究[J]. 航空发动机, 2020, 46(3):99-102. ZHAO W L, LIU X G, XIE P Y, et al. Study on shear fatigue performance of TC4 titanium alloy diffusion bonded joints[J]. Aeroengine, 2020, 46(3):99-102(in Chinese).
[5] 王世清, 邢博, 赵启喆, 等. 不同热处理对TC4/Ti60电子束焊接头微观组织及力学性能的影响[J]. 电焊机, 2020, 50(5):16-20, 133. WANG S Q, XING B, ZHAO Q Z, et al. Effect of heat treatment on microstructure and tensile properties of electron beam welded TC4/Ti60 joint[J]. Electric Welding Machine, 2020, 50(5):16-20, 133(in Chinese).
[6] 杜振宾, 王卫玲, 熊然. TC18钛合金薄壁壳体真空电子束焊接形性控制研究[J]. 焊管, 2020, 43(10):29-34. DU Z B, WANG W L, XIONG R. Study on the weld shape and performance control of vacuum electron beam welding of TC18 titanium alloy thin-walled shell[J]. Welded Pipe and Tube, 2020, 43(10):29-34(in Chinese).
[7] 邵帅, 黄永德, 陈玉华. 钛合金搅拌摩擦焊搅拌头研究现状[J]. 精密成形工程, 2019, 11(5):115-122. SHAO S, HUANG Y D, CHEN Y H. Research status on tools of friction stir welding in titanium alloy[J]. Journal of Netshape Forming Engineering, 2019, 11(5):115-122(in Chinese).
[8] LU Y, TURNER R, BROOKS J, et al. Microstructural characteristics and computational investigation on electron beam welded Ti-6Al-4V alloy[J]. Journal of Materials Processing Technology, 2021, 288:116837.
[9] 李亚江, 王娟, Puchkov P U. 高能束流焊接技术现状及发展[J]. 航空制造技术, 2011, 54(8):38-41. LI Y J, WANG J, PUCHKOV P U. Application and development of advanced welding technology by high-energy density beam[J]. Aeronautical Manufacturing Technology, 2011, 54(8):38-41(in Chinese).
[10] 彭南翔. 激光深熔焊接铝合金孔内菲涅尔吸收研究[D]. 长沙:湖南大学, 2018. PENG N X. Study on Fresnel absorption in the keyhole during deep penetration laser welding of aluminum alloy 6016[D]. Changsha:Hunan University, 2018(in Chinese).
[11] WANG Z M, OLIVEIRA J P, ZENG Z, et al. Laser beam oscillating welding of 5A06 aluminum alloys:Microstructure, porosity and mechanical properties[J]. Optics & Laser Technology, 2019, 111:58-65.
[12] KE W C, BU X Z, OLIVEIRA J P, et al. Modeling and numerical study of keyhole-induced porosity formation in laser beam oscillating welding of 5A06 aluminum alloy[J]. Optics & Laser Technology, 2021, 133:106540.
[13] LI S R, MI G Y, WANG C M. A study on laser beam oscillating welding characteristics for the 5083 aluminum alloy:Morphology, microstructure and mechanical properties[J]. Journal of Manufacturing Processes, 2020, 53:12-20.
[14] 黄瑞生, 邹吉鹏, 宫建锋, 等. 激光扫描焊接熔池及等离子体动态行为[J]. 焊接学报, 2020, 41(3):11-16, 97. HUANG R S, ZOU J P, GONG J F, et al. Dynamic behavior of laser scanning welding pool and plasma[J]. Transactions of the China Welding Institution, 2020, 41(3):11-16, 97(in Chinese).
[15] JIANG Z G, CHEN X, LI H, et al. Grain refinement and laser energy distribution during laser oscillating welding of Invar alloy[J]. Materials & Design, 2020, 186:108195.
[16] 刘宁. TC4钛合金TIG填丝堆焊成型技术研究[D]. 哈尔滨:哈尔滨工业大学, 2013. LIU N. Research on Ti-6Al-4V shaped metal deposition by TIG welding with wire[D]. Harbin:Harbin Institute of Technology, 2013(in Chinese).
[17] XU Z Z, DONG Z Q, YU Z H, et al. Relationships between microhardness, microstructure, and grain orientation in laser-welded joints with different welding speeds for Ti6Al4V titanium alloy[J]. Transactions of Nonferrous Metals Society of China, 2020, 30(5):1277-1289.
[18] AHMED T, RACK H J. Phase transformations during cooling in α+β titanium alloys[J]. Materials Science and Engineering:A, 1998, 243(1-2):206-211.
[19] 官祥威. 光纤激光焦点旋转和垂直振动焊接方法及装置研究[D]. 北京:北京工业大学, 2016. GUAN X W. Investigation on the method and device of fiber laser welding with focus rotation and vertical oscillation[D]. Beijing:Beijing University of Technology, 2016(in Chinese).
[20] 崔约贤, 王长利. 金属断口分析[M]. 哈尔滨:哈尔滨工业大学出版社, 1998. CUI Y X, WANG C L. Metal fracture analysis[M]. Harbin:Harbin Institute of Technology Press, 1998(in Chinese).
[21] CHAMANFAR A, HUANG M F, PASANG T, et al. Microstructure and mechanical properties of laser welded Ti-10V-2Fe-3Al (Ti1023) titanium alloy[J]. Journal of Materials Research and Technology, 2020, 9(4):7721-7731.
[22] 李坤, 王威, 单际国, 等. TC4钛合金光纤激光摆动焊抑制小孔型气孔的原因分析[J]. 焊接学报, 2016, 37(11):43-46, 131. LI K, WANG W, SHAN J G, et al. Analysis of keyhole-type pore suppressing in fiber laser welded TC4 titanium alloy with beam weaving[J]. Transactions of the China Welding Institution, 2016, 37(11):43-46, 131(in Chinese).
[23] LIU H, NAKATA K, ZHANG J X, et al. Microstructural evolution of fusion zone in laser beam welds of pure titanium[J]. Materials Characterization, 2012, 65:1-7.
[24] DU H B, HU L J, HU X Y, et al. Laser welding of TC-1 titanium alloy[J]. Journal of Materials Science & Technology, 2003, 19(5):475-478.
[25] ZHANG D B, WANG M, SHU C S, et al. Dynamic keyhole behavior and keyhole instability in high power fiber laser welding of stainless steel[J]. Optics & Laser Technology, 2019, 114:1-9.
[26] LIU C C, HE J S. Numerical analysis of thermal fluid transport behavior during electron beam welding of 2219 aluminum alloy plate[J]. Transactions of Nonferrous Metals Society of China, 2017, 27(6):1319-1326.
[27] 金湘中, 李力钧. 激光深熔焊接过程中小孔效应的试验研究[J]. 应用激光, 1999(5):293-295, 322. JIN X Z, LI L J. Diathermancy study on keyhole effects in laser deep penetration welding[J]. Applied Laser, 1999(5):293-295, 322(in Chinese).
[28] NING J, ZHANG L J, YIN X Q, et al. Mechanism study on the effects of power modulation on energy coupling efficiency in infrared laser welding of highly-reflective materials[J]. Materials & Design, 2019, 178:107871.
[29] DOWDEN J. Interaction of the keyhole and weld pool in laser keyhole welding[J]. Journal of Laser Applications, 2002, 14(4):204-209.
[30] CUNNINGHAM R, ZHAO C, PARAB N, et al. Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed X-ray imaging[J]. Science, 2019, 363(6429):849-852.
[31] FABBRO R. Melt pool and keyhole behaviour analysis for deep penetration laser welding[J]. Journal of Physics D:Applied Physics, 2010, 43(44):445501.
[32] LI L Q, GONG J F, XIA H B, et al. Influence of scan paths on flow dynamics and weld formations during oscillating laser welding of 5A06 aluminum alloy[J]. Journal of Materials Research and Technology, 2021, 11:19-32.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

扫描振镜激光TC4钛合金焊接性能及熔池流动行为

Welding properties and molten pool flow behavior of TC4 titanium alloy by oscillating galvanometer laser

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	张志强, 于子鸣, 张天刚, 杨倩, 王浩. 激光熔覆TiC _x 增强钛基复合涂层组织与增强相第一性原理研究[J]. 航空学报, 2023, 44(8): 427294-427294.
[2]	刘瑞峰, 孙晓哲, 李文辉, 王显, 闫杰. 高频脉冲电流改性SiC/Al复合材料微裂纹愈合机制及组织性能[J]. 航空学报, 2023, 44(22): 428598-428598.
[3]	赵楠, 李多生, 叶寅, 刘奋成, 江五贵. 激光选区熔化成形GH5188合金微观组织及性能[J]. 航空学报, 2023, 44(19): 428332-428332.
[4]	孙洋, 黄建, 韩晨晨, 赵振强, 周海丽, 孙方方, 李超, 张超, 张立泉. 二维与三维机织复合材料面内力学性能对比[J]. 航空学报, 2023, 44(18): 428267-428267.
[5]	陈江波, 曾凯, 邢保英, 张洪申, 丁燕芳, 何晓聪. 铝合金-胶膜压印/粘接复合连接工艺及接头失效分析[J]. 航空学报, 2023, 44(14): 428029-428029.
[6]	李晖, 吕海宇, 邹泽煜, 罗忠, 马辉, 韩清凯. 热环境下纤维增强复合材料圆柱壳非线性振动分析与验证[J]. 航空学报, 2022, 43(9): 425642-425642.
[7]	罗圣峰, 王光健, 马小斌, 郑丽丽, 汪瑞军. 钛液滴作用下钛合金薄片火蔓延的数值模拟[J]. 航空学报, 2022, 43(9): 425652-425652.
[8]	赵天, 李营, 张超, 姚辽军, 黄怿行, 黄治新, 陈诚, 汪万栋, 祖磊, 周华民, 裘进浩, 邱志平, 方岱宁. 高性能航空复合材料结构的关键力学问题研究进展[J]. 航空学报, 2022, 43(6): 526851-526851.
[9]	刘增飞, 刘凯, 张斌斌, 李雪枫, 葛敬冉, 黄建, 李超, 孙新杨, 孙煜, 梁军. 纱线规格对3D机织复合材料拉伸性能的影响[J]. 航空学报, 2022, 43(6): 525453-525453.
[10]	王秒, 王微, 杨云龙, 檀财旺, 王刚. 钎焊时间对CoFeNiCrCu高熵钎料钎焊SiC陶瓷接头组织与性能的影响[J]. 航空学报, 2022, 43(4): 525057-525057.
[11]	肖贵坚, 刘帅, 贺毅, 刘岗, 朱升旺, 宋沙雨. 钛合金激光砂带加工的离焦控制与表面形貌[J]. 航空学报, 2022, 43(4): 525603-525603.
[12]	彭振龙, 张翔宇, 张德远. 航空航天难加工材料高速超声波动式切削方法[J]. 航空学报, 2022, 43(4): 525587-525587.
[13]	赵可汗, 刘多, 朱海涛, 陈斌, 胡胜鹏, 宋晓国. 钎焊温度对C/C/AgCuTi+C_f/TC4接头组织及力学性能的影响[J]. 航空学报, 2022, 43(4): 525007-525007.
[14]	刘天元, 郑杭彬, 杨长祺, 鲍劲松, 汪俊亮, 顾俊. 面向激光焊接缺陷识别的可解释性深度学习方法[J]. 航空学报, 2022, 43(4): 524961-524961.
[15]	闾川阳, 陈刚强, 唐夏焘, 贺艳明, 杨建国, 郑文健, 马英鹤, 李华鑫, 高增梁. BNi71CrSi钎料钎焊Hastelloy N合金的接头组织和性能[J]. 航空学报, 2022, 43(2): 625040-625040.