紧凑凸肋通道对尾缘劈缝气膜冷却特性的影响

doi:10.7527/S1000-6893.2021.25174

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

紧凑凸肋通道对尾缘劈缝气膜冷却特性的影响

叶林¹, 刘存良^1,2, 朱安冬¹, 周天亮¹

1. 西北工业大学动力与能源学院, 西安 710072;
2. 西北工业大学陕西省航空动力系统热科学重点实验室, 西安 710129

收稿日期:2020-12-28 修回日期:2021-01-07 出版日期:2022-03-15 发布日期:2022-04-02
通讯作者: 刘存良 E-mail:liucunliang@nwpu.edu.cn
基金资助:
国家自然科学基金（51776173）；陕西省杰出青年科学基金（2021JC-11）

Influence of compact-ribbed passage on trailing-edge cutback film cooling performance

YE Lin¹, LIU Cunliang^1,2, ZHU Andong¹, ZHOU Tianliang¹

1. School of Power and Energy, Northwestern Polytechnical University, Xi'an 710072, China;
2. Shaanxi Key Laboratory of Thermal Sciences in Aero-engine System, Northwestern Polytechnical University, Xi'an 710129, China

Received:2020-12-28 Revised:2021-01-07 Online:2022-03-15 Published:2022-04-02
Supported by:
National Natural Science Foundation of China (51776173); Shaanxi Science Foundation for Distinguished Young Scholars (2021JC-11))

摘要/Abstract

摘要： 以稳态压敏漆技术和瞬态热色液晶技术为测量方法，实验研究了尾缘区域凸肋内冷供气通道对外部气膜冷却特性的影响，详细对比分析了直肋间距和吹风比对尾缘劈缝扩张表面的气膜冷却效率、对流换热系数和劈缝流量系数的影响，并引入热流密度比来衡量对比紧凑凸肋通道对劈缝表面的综合冷却效率增强性能。实验结果表明:劈缝流量系数受吹风比的影响较小，随肋间距的增大而减小；凸肋通道明显加强了射流的混乱程度，导致其与主流掺混程度加剧，降低了劈缝表面远下游区域的气膜冷却效率，小肋间距结构气膜冷却效率略高于大肋间距结构，随着吹风比的增大，凸肋通道结构与基准结构的气膜冷却效率差异减小；凸肋通道结构可提升基准结构缝出口区域的低换热性能，尤其对于小肋间距结构，大吹风比时，缝出口的换热核心区沿流向延伸效果增强；具有小肋间距的凸肋通道对尾缘劈缝的综合冷却性能有促进作用，其中肋间距p/h=4结构可提升15%~20%的综合冷却性能，而大肋间距结构明显降低了基准结构的综合冷却性能。

关键词: 涡轮叶片尾缘, 肋间距, 直肋, 气膜冷却, 压力敏感漆, 瞬态热色液晶

Abstract: The influence of the coolant convex-ribbed passage in the trailing-edge internal region on the external film cooling characteristics is experimentally studied, using the steady pressure sensitive paint technology and transient thermochromic liquid crystal technology as the measurement methods.The effects of the straight-rib pitch and the blowing ratio on the film cooling effectiveness and convective heat transfer coefficient of the expanded trailing-edge cutback surface as well as the cutback discharge coefficient are analyzed, and the heat flux ratio introduced to evaluate the enhancement effect on the comprehensive cooling effectiveness of the compact-ribbed cases by comparing with the baseline case.The experimental results show that the cutback discharge coefficient is less affected by the blowing ratio and decreases with the increase of the rib-pitch.The convexity of the jet flow is clearly enhanced by the convex-ribbed passage, aggravating the mixing degree with the mainstream, and reducing the film cooling effectiveness in the far-downstream region of the cutback surface.The film cooling effectiveness of the ribbed case with a small rib-pitch is slightly higher than that of the case with a large rib-pitch.With the increase of the blowing ratio, the difference of the film cooling effectiveness between the cases with convex ribs and the baseline case decreases.The compact-ribbed passage can improve the heat transfer performance of the region near the slot exit, particularly for the cases with the small rib-pitch.At a high blowing ratio, the core heat transfer area near the slot exit extends along the flow direction.The convex-ribbed passage with a small rib-pitch can promote the comprehensive cooling performance of the trailing edge cutback, among which the case with rib-pitch p/h=4 improves the comprehensive cooling performance by 15%-20%, while the large rib-pitch cases significantly reduce the comprehensive cooling performance compared with the baseline case.

Key words: turbine blade trailing-edge, rib-pitch, straight rib, film cooling, pressure sensitive paint, transient thermochromic liquid crystal

中图分类号:

V231.1

叶林, 刘存良, 朱安冬, 周天亮. 紧凑凸肋通道对尾缘劈缝气膜冷却特性的影响[J]. 航空学报, 2022, 43(3): 125174-125174.

YE Lin, LIU Cunliang, ZHU Andong, ZHOU Tianliang. Influence of compact-ribbed passage on trailing-edge cutback film cooling performance[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(3): 125174-125174.

参考文献

[1] 李军, 栗智宇, 李志刚, 等.燃烧室和涡轮相互作用下高压涡轮级气热性能研究进展[J].航空学报, 2021, 42(3):024111. LI J, LI Z Y, LI Z G, et al.Aerothermal performance of high pressure turbine stage with combustor-turbine interactions:Review[J].Acta Aeronautica et Astronautica Sinica, 2021, 42(3):024111(in Chinese).
[2] CUNHA F J, CHYU M K.Trailing-edge cooling for gas turbines[J].Journal of Propulsion and Power, 2006, 22(2):286-300.
[3] CUNHA F J, DAHMER M T, CHYU M K.Analysis of airfoil trailing edge heat transfer and its significance in thermal-mechanical design and durability[J].Journal of Turbomachinery, 2006, 128(4):738-746.
[4] UZOL O, CAMCI C.Aerodynamic loss characteristics of a turbine blade with trailing edge coolant ejection:Part 2-External aerodynamics, total pressure losses, and predictions[J].Journal of Turbomachinery, 2001, 123(2):249-257.
[5] TASLIM M E, SPRING S D, MEHLMAN B P.An experimental investigation of film cooling effectiveness for slots of various exit geometries:AIAA-1990-2266[R].Reston:AIAA, 1990.
[6] SIVASEGARAM S, WHITELAW J H.Film cooling slots:The importance of lip thickness and injection angle[J].Journal of Mechanical Engineering Science, 1969, 11(1):22-27.
[7] KACKER S C, WHITELAW J H.An experimental investigation of the influence of slot-lip-thickness on the impervious-wall effectiveness of the uniform-density, two-dimensional wall jet[J].International Journal of Heat and Mass Transfer, 1969, 12(9):1196-1201.
[8] HORBACH T, SCHULZ A, BAUER H J.Trailing edge film cooling of gas turbine airfoils-External cooling performance of various internal pin fin configurations[J].Journal of Turbomachinery, 2011, 133(4):041006.
[9] HORBACH T, SCHULZ A, BAUER H J.Trailing edge film cooling of gas turbine airfoils-Effects of ejection lip geometry on film cooling effectiveness and heat transfer[J].Heat Transfer Research, 2010, 41(8):849-865.
[10] 王茜, 何坤, 晏鑫.带肋尾缘开缝模型内的非定常冷却性能研究[J].西安交通大学学报, 2020, 54(9):128-135. WANG X, HE K, YAN X.Investigation of unsteady cooling performance in a trailing edge cutback model with land extensions[J].Journal of Xi'an Jiaotong University, 2020, 54(9):128-135(in Chinese).
[11] 原和朋.涡轮叶片尾缘半劈缝的换热特性研究[D].西安:西北工业大学, 2008:39-44. YUAN H P.Investigation of heat transfer characteristics on the trailing edge cutback of turbine airfoils[D].Xi'an:Northwestern Polytechnical University, 2008:39-44(in Chinese).
[12] RALLABANDI A P, LIU Y H, HAN J C.Heat transfer in trailing edge wedge-shaped pin-fin channels with slot ejection under high rotation numbers[J].Journal of Thermal Science and Engineering Applications, 2011, 3(2):021007.
[13] WU H, LIU Y S, XU G Q.Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade[J].Chinese Journal of Aeronautics, 2013, 26(2):294-308.
[14] MARTINI P, SCHULZ A, BAUER H J.Film cooling effectiveness and heat transfer on the trailing edge cutback of gas turbine airfoils with various internal cooling designs[J].Journal of Turbomachinery, 2006, 128(1):196-205.
[15] MARTINI P, SCHULZ A, BAUER H J, et al.Detached eddy simulation of film cooling performance on the trailing edge cutback of gas turbine airfoils[J].Journal of Turbomachinery, 2006, 128(2):292-299.
[16] KRUECKELS J, GRITSCH M, SCHNIEDER M.Design considerations and validation of trailing edge pressure side bleed cooling:GT2009-59161[R].New York:ASME, 2009.
[17] ZHANG J Z, ZHANG S C, WANG C H, et al.Recent advances in film cooling enhancement:A review[J].Chinese Journal of Aeronautics, 2020, 33(4):1119-1136.
[18] ZHANG S C, ZHANG J Z, TAN X M.Improvement on shaped-hole film cooling effectiveness by integrating upstream sand-dune-shaped ramps[J].Chinese Journal of Aeronautics, 2021, 34(4):42-55.
[19] 陈大为, 朱惠人, 李华太, 等.尾迹对涡轮动叶全表面气膜冷却效率的影响[J].航空学报, 2019, 40(3):122651. CHEN D W, ZHU H R, LI H T, et al.Effect of unsteady wake on full coverage film cooling effectiveness for a turbine blade[J].Acta Aeronautica et Astronautica Sinica, 2019, 40(3):122651(in Chinese).
[20] 叶林, 刘存良, 杨寓全, 等.V肋对尾缘劈缝气膜冷却特性的影响[J].航空学报, 2021, 42(6):124181. YE L, LIU C L, YANG Y Q, et al.Effect of V-shaped ribs on film cooling characteristics of trailing-edge cutback[J].Acta Aeronautica et Astronautica Sinica, 2021, 42(6):124181(in Chinese).
[21] 刘存良, 朱惠人, 白江涛, 等.基于瞬态液晶测量技术的收缩-扩张形孔气膜冷却特性[J].航空学报, 2009, 30(5):812-818. LIU C L, ZHU H R, BAI J T, et al.Film cooling characteristics of converging-expanding hole with transient liquid crystal measurement technique[J].Acta Aeronautica et Astronautica Sinica, 2009, 30(5):812-818(in Chinese).
[22] YE L, LIU C L, ZHOU D E, et al.Experimental and numerical investigations on the heat transfer of film cooling with cylindrical holes fed with internal coolant cross flows[J].Journal of Heat Transfer, 2020, 142(5):052302.
[23] KAYS W, CRAWFORD M.Convective heat and mass transfer[M].3rd ed.New York:McGraw-Hill, 1993:316.
[24] MURATA A, NISHIDA S, SAITO H, et al.Effects of surface geometry on film cooling performance at airfoil trailing edge:GT2011-45355[R].New York:ASME, 2011.
[25] HOLLOWAY D S, LEYLEK J H, BUCK F A.Pressure side bleed film cooling:Part II-Unsteady framework for experimental and computational results:GT2002-30472[R].New York:ASME, 2002.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

紧凑凸肋通道对尾缘劈缝气膜冷却特性的影响

Influence of compact-ribbed passage on trailing-edge cutback film cooling performance

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王斌, 王海涛, 王玉峰, 张文武. 热障涂层水助激光扫描加工试验[J]. 航空学报, 2022, 43(4): 525353-525353.
[2]	夏凯龙, 何箐, 张雨生. 基于红外热成像的涡轮叶片气膜孔孔径测量方法及缩孔规律[J]. 航空学报, 2022, 43(12): 426271-426271.
[3]	罗世彬, 庙智超, 宋佳文. 高超声速飞行器前缘主动冷却影响因素[J]. 航空学报, 2022, 43(12): 627023-627023.
[4]	杨寓全, 刘存良, 张杰, 黄蓉. 分腔流量比对涡轮曲端壁表面冷却特性实验[J]. 航空学报, 2021, 42(7): 124399-124399.
[5]	王进, 孙杰, 赵占明, 张勃, 任晓栋, 谢公南. 基于结构参数分析的姊妹孔气膜冷却性能研究[J]. 航空学报, 2021, 42(7): 124775-124775.
[6]	叶林, 刘存良, 杨寓全, 黄蓉, 朱安冬. V肋对尾缘劈缝气膜冷却特性的影响[J]. 航空学报, 2021, 42(6): 124181-124181.
[7]	李左飙, 温风波, 唐晓雷, 苏良俊, 王松涛. 基于深度学习的单排孔气膜冷却性能预测[J]. 航空学报, 2021, 42(4): 524331-524331.
[8]	陈大为, 朱惠人, 李华太, 刘海涌, 周道恩. 尾迹对涡轮动叶全表面气膜冷却效率的影响[J]. 航空学报, 2019, 40(3): 122651-122651.
[9]	祝培源, 宋立明, 李军, 丰镇平. 间隙位置和几何对端壁冷却性能的影响[J]. 航空学报, 2017, 38(9): 520942-520942.
[10]	张靖周, 王旭, 单勇. 塞锥后体气膜冷却对轴对称塞式喷管红外辐射和气动性能的影响[J]. 航空学报, 2015, 36(8): 2601-2608.
[11]	张晓兵, 孙瑞峰. 二次法激光加工小孔技术[J]. 航空学报, 2014, 35(3): 894-901.
[12]	丁阳, 常海萍. 涡轮叶片冷却有效性分析[J]. 航空学报, 2013, 34(1): 46-51.
[13]	杨彬;徐国强. 旋转状态下孔排构型气膜冷却特性实验研究[J]. 航空学报, 2010, 31(8): 1524-1537.
[14]	姚玉;张靖周;何飞;郭文. 涡轮叶片吸力面上收敛缝形孔气膜冷却对叶栅气动损失的影响[J]. 航空学报, 2010, 31(7): 1312-1317.
[15]	李广超;张魏;彭大维;王成军. 带锥形扩张支孔射流气膜冷却效率数值模拟[J]. 航空学报, 2010, 31(7): 1360-1365.