不锈钢增材制造件后处理工艺研究进展

doi:10.7527/S1000-6893.2021.25847

Abstract

Abstract: The parts fabricated by Additive Manufacturing (AM) cannot be used directly due to the defects caused by layer-by-layer formation of AM, including coarse surface, high residual stress, and pores/micro cracks beneath the surface caused by insufficient melting. The review summarizes the research results of the post-treatment processes of stainless steel additive manufacturing components at home and abroad and the defect types of stainless steel additive manufacturing components, analyzes the differences and uses of different additive manufacturing processes, and current domestic and international optimization progress of the process parameters of the additive manufacturing components, heat treatment, mechanical processing and other post-treatment processes, The key problems of post-treatment process of stainless steel additive manufacturing pieces are summarized, and the development trend of post-treatment process of stainless steel additive manufacturing pieces is discussed.

Key words: additive manufacturing, stainless steel material, post-processing technology, machinability, residual stress

CLC Number:

V261.2⁺1

LI Hui, LI Guangxian, GAO Ruilin, JIN Xin, LIU Lu, LI Chaojiang, Songlin DING. Research progress of post-processing of stainless steel additive manufacturing parts[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525847-525847.

References

[1] 卢秉恒. 增材制造技术:现状与未来[J]. 中国机械工程, 2020, 31(1):19-23. LU B H. Additive manufacturing-Current situation and future[J]. China Mechanical Engineering, 2020, 31(1):19-23(in Chinese).
[2] 熊云龙, 娄延春, 刘新峰. 不锈钢材料研究的新进展[J]. 热加工工艺, 2005, 34(5):51-53. XIONG Y L, LOU Y C, LIU X F. New progress of stainless steel[J]. Hot Working Technology, 2005, 34(5):51-53(in Chinese).
[3] 周建涛. 硬质合金刀具车削半奥氏体沉淀硬化不锈钢的磨损机理研究[D]. 济南:山东大学, 2010:1-2. ZHOU J T. Wear mechanisms of cemented carbide tools in turning of semi-austenitic precipitation hardening stainless steel[D]. Jinan:Shandong University, 2010:1-2(in Chinese).
[4] 张国平. 不锈钢切削加工[J]. 现代机械, 2013(1):65-67, 70. ZHANG G P. Stainless steel cutting processing[J]. Modern Machinery, 2013(1):65-67, 70(in Chinese).
[5] 周芳娟. 304不锈钢切削加工表面特性的研究[D]. 武汉:华中科技大学, 2014:1-2. ZHOU F J. Research on machined surface characteristics of304Stainless steel[D]. Wuhan:Huazhong University of Science and Technology, 2014:1-2(in Chinese).
[6] 章媛洁, 宋波, 赵晓, 等. 激光选区熔化增材与机加工复合制造AISI 420不锈钢:表面粗糙度与残余应力演变规律研究[J]. 机械工程学报, 2018, 54(13):170-178. ZHANG Y J, SONG B, ZHAO X, et al. Selective laser melting and subtractive hybrid manufacture AISI420 stainless steel:Evolution on surface roughness and residual stress[J]. Journal of Mechanical Engineering, 2018, 54(13):170-178(in Chinese).
[7] 方金祥. 激光熔覆成形马氏体不锈钢应力演化及调控机制[D]. 哈尔滨:哈尔滨工业大学, 2016:2-3. FANG J X. Evolution and control of stress during laser cladding forming of martensitic stainless steel[D]. Harbin:Harbin Institute of Technology, 2016:2-3(in Chinese).
[8] EDWARDS P, RAMULU M. Fatigue performance evaluation of selective laser melted Ti-6Al-4V[J]. Materials Science and Engineering:A, 2014, 598:327-337.
[9] ZHU J H, ZHOU H, WANG C, et al. A review of topology optimization for additive manufacturing:Status and challenges[J]. Chinese Journal of Aeronautics, 2021, 34(1):91-110.
[10] 耿海滨, 熊江涛, 黄丹, 等. 丝材电弧增材制造技术研究现状与趋势[J]. 焊接, 2015(11):17-21, 69. GENG H B, XIONG J T, HUANG D, et al. Research status and trends of wire and arc additive manufacturing technology[J]. Welding & Joining, 2015(11):17-21, 69(in Chinese).
[11] 熊江涛, 耿海滨, 林鑫, 等. 电弧增材制造研究现状及在航空制造中应用前景[J]. 航空制造技术, 2015, 58(增刊2):80-85. XIONG J T, GENG H B, LIN X, et al. Research status of wire and arc additive manufacture and its application in aeronautical manufacturing[J]. Aeronautical Manufacturing Technology, 2015, 58(Sup.2):80-85(in Chinese).
[12] PARVARESH B, SALEHAN R, MIRESMAEILI R. Investigating isotropy of mechanical and wear properties in as-deposited and inter-layer cold worked specimens manufactured by wire arc additive manufacturing[J]. Metals and Materials International, 2021, 27(1):92-105.
[13] American Society for Testing and Materials. Standard specification for chromium and chromium-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications:ASTM-A240/A240Ma-2002[S]. West Conshohocken:ASTM International, 2002.
[14] KONG D C, NI X Q, DONG C F, et al. Anisotropy in the microstructure and mechanical property for the bulk and porous 316L stainless steel fabricated via selective laser melting[J]. Materials Letters, 2019, 235:1-5.
[15] 刘奋成, 贺立华, 黄春平, 等. 316L不锈钢电弧堆焊快速成形工艺及组织性能研究[J]. 南昌航空大学学报(自然科学版), 2013, 27(4):1-5. LIU F C, HE L H, HUANG C P, et al. Microstructure, mechanical properties and processing study of arc overlying welding rapid forming of 316L stainless steel[J]. Journal of Nanchang Hangkong University (Natural Sciences), 2013, 27(4):1-5(in Chinese).
[16] CHEN X H, LI J, CHENG X, et al. Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing[J]. Materials Science and Engineering:A, 2017, 703:567-577.
[17] 周斌, 张婷, 林峰, 等. 电子束选区熔化成形Ti6Al4V和316L不锈钢叶轮体微观组织和力学性能的研究[J]. 稀有金属材料与工程, 2018, 47(1):175-180. ZHOU B, ZHANG T, LIN F, et al. Microstructures and mechanical properties of Ti6Al4V and 316L stainless steel impeller body made by electron beam selective melting[J]. Rare Metal Materials and Engineering, 2018, 47(1):175-180(in Chinese).
[18] KARLSSON J, SNIS A, ENGQVIST H, et al. Characteri-zation and comparison of materials produced by electron beam melting (EBM) of two different Ti-6Al-4V powder fractions[J]. Journal of Materials Processing Tech, 2013, 213(12):2109-2118.
[19] 王忻凯, 王乾俸. 增材制造及其航空航天领域的发展现状[J]. 中小企业管理与科技, 2015(12):230-231. WANG X K, WANG Q F. Additive manufacturing and its development status in aerospace field[J]. Management & Technology of SME, 2015(12):230-231(in Chinese).
[20] 席明哲, 高士友. 激光快速成形Rene 80高温合金组织及裂纹形成机理[J]. 中国激光, 2012, 39(8):0803008. XI M Z, GAO S Y. Microstructures and mechanism of cracks forming of Rene 80 high-temperature alloy fabricated by laser rapid forming process[J]. Chinese Journal of Lasers, 2012, 39(8):0803008(in Chinese).
[21] 宋建丽, 邓琦林, 葛志军, 等. 镍基合金激光快速成形裂纹控制技术[J]. 上海交通大学学报, 2006, 40(3):548-552. SONG J L, DENG Q L, GE Z J, et al. The cracking control technology of laser rapid forming nickel-based alloys[J]. Journal of Shanghai Jiao Tong University, 2006, 40(3):548-552(in Chinese).
[22] 杨健, 黄卫东, 陈静, 等. 激光快速成形金属零件的残余应力[J]. 应用激光, 2004, 24(1):5-8. YANG J, HUANG W D, CHEN J, et al. Residual stress on laser rapid forming metal part[J]. Applied Laser, 2004, 24(1):5-8(in Chinese).
[23] WITTIG B, ZINKE M, JVTTNER S. Influence of arc energy and filler metal composition on the microstructure in wire arc additive manufacturing of duplex stainless steels[J]. Welding in the World, 2021, 65(1):47-56.
[24] 张炼. 316不锈钢TIG电弧增材制造工艺及性能研究[D]. 大连:大连理工大学, 2019:9-10. ZHANG L. Research on process and performance of 316 stainless steel TIG arc additive manufacturing[D]. Dalian:Dalian University of Technology, 2019:9-10(in Chinese).
[25] XU X, MI G Y, LUO Y Q, et al. Morphologies, microstructures, and mechanical properties of samples produced using laser metal deposition with 316 L stainless steel wire[J]. Optics and Lasers in Engineering, 2017, 94:1-11.
[26] 李旭文, 宋刚, 张兆栋, 等. 激光诱导电弧复合增材制造316不锈钢的组织和性能[J]. 中国激光, 2019, 46(12):1202006. LI X W, SONG G, ZHANG Z D, et al. Microstructure and properties of 316 stainless steel produced by laser-induced arc hybrid additive manufacturing[J]. Chinese Journal of Lasers, 2019, 46(12):1202006(in Chinese).
[27] 齐海波, 林峰, 颜永年, 等. 316L不锈钢粉末的电子束选区熔化成形[J]. 清华大学学报(自然科学版), 2007, 47(11):1941-1944. QI H B, LIN F, YAN Y N, et al. Electron beam selective melting of 316L stainless steel powder[J]. Journal of Tsinghua University (Science and Technology), 2007, 47(11):1941-1944(in Chinese).
[28] 郭超, 林峰, 葛文君. 电子束选区熔化成形316L不锈钢的工艺研究[J]. 机械工程学报, 2014, 50(21):152-158. GUO C, LIN F, GE W J. Study on the fabrication process of 316L stainless steel via electron beam selective melting[J]. Journal of Mechanical Engineering, 2014, 50(21):152-158(in Chinese).
[29] 任香会, 张文杰, 易耀勇, 等. ER308L不锈钢丝材微束等离子弧增材制造组织与性能分析[J]. 沈阳航空航天大学学报, 2019, 36(6):27-32. REN X H, ZHANG W J, YI Y Y, et al. Microstructure and mechanical properties of mateirals fabricated by micro-plasma arc additive manufacturing from ER308L wire[J]. Journal of Shenyang Aerospace University, 2019, 36(6):27-32(in Chinese).
[30] WANG Y D, TANG H B, FANG Y L, et al. Microstructure and mechanical properties of hybrid fabricated 1Cr12Ni2WMoVNb steel by laser melting deposition[J]. Chinese Journal of Aeronautics, 2013, 26(2):481-486.
[31] BENARJI K, RAVI KUMAR Y, JINOOP A N, et al. Effect of heat-treatment on the microstructure, mechanical properties and corrosion behaviour of SS 316 structures built by laser directed energy deposition based additive manufacturing[J]. Metals and Materials International, 2021, 27(3):488-499.
[32] 赵晓. 激光选区熔化成形模具钢材料的组织与性能演变基础研究[D]. 武汉:华中科技大学, 2016:140-142. ZHAO X. Fundamental research on the microstructure and properties evolution of tool steels fabricated by selective laser melting[D]. Wuhan:Huazhong University of Science and Technology, 2016:140-142(in Chinese).
[33] 程灵钰, 朱小刚, 刘正武, 等. 热处理对激光选区熔化成形316L不锈钢组织和力学性能的影响[J]. 材料热处理学报, 2020, 41(7):80-86. CHENG L Y, ZHU X G, LIU Z W, et al. Effect of heat treatment on microstructure and mechanical properties of 316L stainless steel prepared by selective laser melting[J]. Transactions of Materials and Heat Treatment, 2020, 41(7):80-86(in Chinese).
[34] 边培莹. 热处理工艺对316L不锈钢粉末激光选区熔化成形的残余应力及组织的影响[J]. 材料热处理学报, 2019, 40(4):90-97. BIAN P Y. Effect of heat treatment on residual stress and microstructure of 316L stainless steel powder formed by selective laser melting[J]. Transactions of Materials and Heat Treatment, 2019, 40(4):90-97(in Chinese).
[35] 徐亮, 杨可, 王秋雨, 等. 热处理对电弧增材制造316L不锈钢组织和性能的影响[J]. 电焊机, 2020, 50(10):29-34, 126. XU L, YANG K, WANG Q Y, et al. Effect of heat treatment on microstructure properties of austenitic stainless steel 316L using arc additive manufacturing[J]. Electric Welding Machine, 2020, 50(10):29-34, 126(in Chinese).
[36] 王智勇, 张毅, 王鑫, 等. 热处理工艺对G30钢组织和性能的影响[J]. 材料热处理学报, 2018, 39(7):92-98. WANG Z Y, ZHANG Y, WANG X, et al. Effect of heat treatment on microstructure and properties of G30 steel[J]. Transactions of Materials and Heat Treatment, 2018, 39(7):92-98(in Chinese).
[37] 王臣, 赵坤. 不锈钢的机械加工特性和方法探讨[J]. 装备制造技术, 2011(6):193-194. WANG C, ZHAO K. Discuss mechanical processing properties and methods of stainless steel[J]. Equipment Manufacturing Technology, 2011(6):193-194(in Chinese).
[38] 徐林红. 难加工材料可加工性分析方法的研究[D]. 武汉:武汉理工大学, 2010. XU L H. Research on the machinability evaluation method for difficult-to-cut materials[D]. Wuhan:Wuhan University of Technology, 2010(in Chinese).
[39] VENKATA RAO R. Machinability evaluation of work materials using a combined multiple attribute decision-making method[J]. The International Journal of Advanced Manufacturing Technology, 2006, 28(3-4):221-227.
[40] RAO R V, GANDHI O P. Digraph and matrix methods for the machinability evaluation of work materials[J]. International Journal of Machine Tools and Manufacture, 2002, 42(3):321-330.
[41] BOUBEKRI N, RODRIGUEZ J, ASFOUR S. Development of an aggregate indicator to assess the machinability of steels[J]. Journal of Materials Processing Technology, 2003, 134(2):159-165.
[42] ENACHE S, STRÂJESCU E, OPRAN C, et al. Mathematical model for the establishment of the materials machinability[J]. CIRP Annals, 1995, 44(1):79-82.
[43] LI G X, YI S, WEN C E, et al. Wear mechanism and modeling of tribological behavior of polycrystalline diamond tools when cutting Ti6Al4V[J]. Journal of Manufacturing Science and Engineering, 2018, 140(12):121011.
[44] LI G X, YI S, SUN S J, et al. Wear mechanisms and performance of abrasively ground polycrystalline diamond tools of different diamond grains in machining titanium alloy[J]. Journal of Manufacturing Processes, 2017, 29:320-331.
[45] ZHANG P R, DU J, ZHANG J J, et al. A theoretical model to study the cutting force characteristics in remanufacturing turning of laser cladded coatings[J]. The International Journal of Advanced Manufacturing Technology, 2021, 113(3-4):757-769.
[46] 白海清, 沈钰, 安熠蔚, 等. 304不锈钢与其激光熔覆件小孔钻削的对比研究[J]. 应用激光, 2020, 40(1):1-6. BAI H Q, SHEN Y, AN Y W, et al. Comparative study on small hole drilling of 304 stainless steel and its laser cladding parts[J]. Applied Laser, 2020, 40(1):1-6(in Chinese).
[47] 白海清, 沈钰, 舒林森, 等. 304不锈钢激光熔覆件的制备及小孔钻削实验研究[J]. 热加工工艺, 2020, 49(10):84-88, 91. BAI H Q, SHEN Y, SHU L S, et al. Preparation of laser cladding 304 stainless steel and experimental study on small hole drilling[J]. Hot Working Technology, 2020, 49(10):84-88, 91(in Chinese).
[48] 高飞, 白海清, 安熠蔚, 等. 316L不锈钢增材成型件小孔钻削试验研究[J]. 现代制造工程, 2019(9):48-53, 36. GAO F, BAI H Q, AN Y W, et al. Experimental research on small hole drilling of 316L stainless steel additive forming parts[J]. Modern Manufacturing Engineering, 2019(9):48-53, 36(in Chinese).
[49] 沈钰. 不锈钢激光熔覆件的小直径孔钻削试验研究[D]. 汉中:陕西理工大学, 2019:4-5. SHEN Y. Experimental research on small diameter hole drilling of stainless steel laser cladding[D]. Hanzhong:Shaanxi University of Technology, 2019:4-5(in Chinese).
[50] 安熠蔚, 白海清, 鲍骏, 等. 316L不锈钢激光熔覆成形件铣削表面质量分析[J]. 机床与液压, 2021, 49(22):61-66. AN Y W, BAI H Q, BAO J, et al. Analysis on milling surface quality of 316L stainless steel laser cladding forming parts[J]. Machine Tool & Hydraulics, 2021, 49(22):61-66(in Chinese).
[51] WANG G R, CHU F, TAO S Y, et al. Optimization design for throttle valve of managed pressure drilling based on CFD erosion simulation and response surface methodology[J]. Wear, 2015, 338-339:114-121.
[52] RAJESWARI B, AMIRTHAGADESWARAN K S. Experimental investigation of machinability characteristics and multi-response optimization of end milling in aluminium composites using RSM based grey relational analysis[J]. Measurement, 2017, 105:78-86.
[53] 郭鹏. 激光增材制造不锈钢的力学性能和铣削性能研究[D]. 济南:山东大学, 2017:69-70. GUO P. Study on mechanical properties and milling performance of stainless steel manufactured by laser additive manufacturing[D]. Jinan:Shandong University, 2017:69-70(in Chinese).
[54] MA M M, WANG Z M, GAO M, et al. Layer thickness dependence of performance in high-power selective laser melting of 1Cr18Ni9Ti stainless steel[J]. Journal of Materials Processing Technology, 2015, 215:142-150.
[55] TRIVEDI R, SEETHARAMAN V, ESHELMAN M A. The effects of interface kinetics anisotropy on the growth direction of cellular microstructures[J]. Metallurgical Transactions A, 1991, 22(2):585-593.
[56] OH J W, LOUCA L A, CHOO Y S. Strain rate effects on the response of stainless steel corrugated firewalls subjected to hydrocarbon explosions[J]. Journal of Constructional Steel Research, 2004, 60(1):1-29.
[57] KAYNAK Y, KITAY O. The effect of post-processing operations on surface characteristics of 316L stainless steel produced by selective laser melting[J]. Additive Manufacturing, 2019, 26:84-93.
[58] YAMAGUCHI H, FERGANI O, WU P Y. Modification using magnetic field-assisted finishing of the surface roughness and residual stress of additively manufactured components[J]. CIRP Annals, 2017, 66(1):305-308.
[59] CHOMIENNE V, VALIORGUE F, RECH J, et al. Influence of ball burnishing on residual stress profile of a 15-5PH stainless steel[J]. CIRP Journal of Manufacturing Science and Technology, 2016, 13:90-96.
[60] LI G X, RAHIM M Z, DING S L, et al. Performance and wear analysis of polycrystalline diamond (PCD) tools manufactured with different methods in turning titanium alloy Ti-6Al-4V[J]. The International Journal of Advanced Manufacturing Technology, 2016, 85(1-4):825-841.
[61] TAPOGLOU N, CLULOW J. Investigation of hybrid manufacturing of stainless steel 316L components using direct energy deposition[J]. Proceedings of the Institution of Mechanical Engineers, Part B:Journal of Engineering Manufacture, 2021, 235(10):1633-1643.
[62] GONG Y D, LI P F. Analysis of tool wear performance and surface quality in post milling of additive manufactured 316L stainless steel[J]. Journal of Mechanical Science and Technology, 2019, 33(5):2387-2395.
[63] BAI Q, WU B Z, QIU X L, et al. Experimental study on additive/subtractive hybrid manufacturing of 6511 steel:Process optimization and machining characteristics[J]. The International Journal of Advanced Manufacturing Technology, 2020, 108(5-6):1389-1398.
[64] TÖNSHOFF H K, ARENDT C, AMOR R B. Cutting of hardened steel[J]. CIRP Annals, 2000, 49(2):547-566.
[65] FANG J X, DONG S Y, WANG Y J, et al. The effects of solid-state phase transformation upon stress evolution in laser metal powder deposition[J]. Materials & Design, 2015, 87:807-814.

Research progress of post-processing of stainless steel additive manufacturing parts

RichHTML

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	LIU Zhendong, ZHENG Xitao, FAN Wenjing, ZHANG Dongjian. Effect of process-induced residual stress on strength of UAV composite wing [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(6): 526117-526117.
[2]	LI Dichen, LU Zhongliang, TIAN Xiaoyong, ZHANG Hang, YANG Chuncheng, CAO Yi, MIAO Kai. Additive manufacturing—Revolutionary technology for leading aerospace manufacturing [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525387-525387.
[3]	YAO Yansheng, ZHOU Ruigen, ZHANG Chenglin, MEI Tao, WU Min. Surface polishing technology for additive manufacturing of complex metal components [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525202-525202.
[4]	ZHANG Peiyu, ZHOU Xin, LI Yinghong. Progress on high energy beam repair of single crystal turbine blades [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525610-525610.
[5]	LI Zhiqiang, CHEN Wei. Application progress of power beam processing technology in aeronautical industry [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 526882-526882.
[6]	WANG Tianshuai, HE Xiaofan, WANG Jinyu, LI Yuhai. Estimation method for DFR value of DED-TA15 titanium alloy based on bimodal lognormal distribution [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(3): 225013-225013.
[7]	SHANG Yong, FENG Yang, LIU Qiaomu, WANG Junwu, YANG Huijun, RU Yi, ZHANG Heng, ZHAO Wenyue, PEI Yanling, LI Shusuo, GONG Shengkai. Research and application of large scientific facility on high-temperature structural materials and coatings of aero-engine [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(10): 527481-527481.
[8]	WANG Lianqing, HU Ya'nan, CHE Zhigang, WU Shengchuan. Fatigue performance of laser shock processed fusion welded 7075 Al alloy [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(5): 524320-524320.
[9]	SHI Binbin, CHEN Zhehan. Defect detection method of powder bed based on image feature fusion [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524430-524430.
[10]	HUANG Jieguang, QI Lehua, LUO Jun. Experimental research and regulation mechanism of critical parameters on horizontal ejection of metal droplets [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524637-524637.
[11]	CAO Longchao, ZHOU Qi, HAN Yuanfei, SONG Bo, NIE Zhenguo, XIONG Yi, XIA Liang. Review on intelligent monitoring of defects and process control of selective laser melting additive manufacturing [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524790-524790.
[12]	GU Dongdong, ZHANG Han, LIU Gang, YANG Biqi. Process optimization of additive manufactured sandwich panel structure using rare earth element modified high-performance Al alloy [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524868-524868.
[13]	GUO Xinxin, CHEN Zhehan. Numerical simulation of laser additive manufacturing process: A review [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524227-524227.
[14]	HAN Kunpeng, ZHANG Dinghua, YAO Changfeng, TAN Liang, ZHOU Zheng. Fatigue evolution and anti-fatigue mechanism of surface characteristics induced by deep rolling: A review [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524302-524302.
[15]	YUAN Jingwei, LI Zhuo, TANG Haibo, CHENG Xu. Effect of heat treatment on corrosion resistance and room temperature compression creep of LAMed TC4 alloy [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524390-524390.