V肋对尾缘劈缝气膜冷却特性的影响

doi:10.7527/S1000-6893.2020.24181

Abstract

Abstract: The influence of the V-shaped ribs on the film cooling characteristics of the trailing-edge cutback is studied using the pressure-sensitive paint technology and the transient thermochromic liquid-crystal technology. The distributions of the film cooling effectiveness and heat transfer coefficients on different cutback surfaces with varying V-shaped rib widths at varying blowing ratios are obtained. The heat flux ratio is adopted to evaluate and compare the overall cooling performance of the turbulated cutback surfaces with V-shaped ribs. The experimental results show that the addition of V-shaped ribs has an adverse effect on the film coverage on the unexpanded surface. At low blowing ratios, the rib width has no significant effect on the area-averaged film cooling effectiveness. For the cases with the same rib width, the film cooling effectiveness of the unexpanded surface is always higher than that of the expanded surface. The effect of the V-shaped rib width on the heat transfer enhancement of the trailing-edge cutback is not obvious. The V-shaped ribs exhibit a stronger heat transfer performance on the unexpanded surface than that on the expanded surface. Compared with the primeval trailing-edge cutback, the net heat flux reduction of the case with V-shaped ribs can significantly increase by a factor of 6.9%-26.6%, and the width has no significant effect on the wall heat flux. At low blowing ratios, it is advisable to use V-shaped ribs on the unexpanded surface, while unnecessary to consider the shape of the trailing-edge cutback at high blowing ratios.

Key words: trailing-edge cutback, V-shaped rib, film cooling, heat transfer enhancement, pressure sensitive paint technique, transient thermochromic liquid-crystal technique

CLC Number:

V231.1

YE Lin, LIU Cunliang, YANG Yuquan, HUANG Rong, ZHU Andong. Effect of V-shaped ribs on film cooling characteristics of trailing-edge cutback[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(6): 124181-124181.

References

[1] 程荣辉, 张志舒, 陈仲光. 第四代战斗机动力技术特征和实现途径[J]. 航空学报, 2019, 40(3):022698. CHENG R H, ZHANG Z S, CHEN Z G. Technical characteristics and implementation of the fourth-generation jet fighter engines[J]. Acta Aeronautica et Astronautica Sinica, 2019, 40(3):022698(in Chinese).
[2] 屠敏, 袁耿民, 薛飞, 等. 综合热管理在先进战斗机系统研制中的应用[J]. 航空学报, 2020, 41(6):523629. TU M, YUAN G M, XUE F, et al. Application of integrated thermal management in development of advanced fighter system[J]. Acta Aeronautica et Astronautica Sinica, 2020, 41(6):523629(in Chinese).
[3] CUNHA F J, DAHMER M T, CHYU M K. Analysis of airfoil trailing edge heat transfer and its significance in thermal-mechanical design and durability[J]. Journal of Turbomachinery, 2006, 128(4):738-746.
[4] CUNHA F J, CHYU M K. Trailing-edge cooling for gas turbines[J]. Journal of Propulsion and Power, 2006, 22(2):286-300.
[5] MARTINI P, SCHULZ A, BAUER H J. Film cooling effectiveness and heat transfer on the trailing edge cutback of gas turbine airfoils with various internal cooling designs[J]. Journal of Turbomachinery, 2006, 128(1):196-205.
[6] WU H, LIU Y S, XU G Q. Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade[J]. Chinese Journal of Aeronautics, 2013, 26(2):294-308.
[7] SHEN Z Y, XIE Y H, ZHANG D. Experimental and numerical study on heat transfer in trailing edge cooling passages with dimples/protrusions under the effect of side wall slot ejection[J]. International Journal of Heat and Mass Transfer, 2016, 92:1218-1235.
[8] MUKHERJEE D K. Film cooling with injection through slots[J]. Journal of Engineering for Power, 1976, 98(4):556-559.
[9] HORBACH T, SCHULZ A, BAUER H J. Trailing edge film cooling of gas turbine airfoils-Effects of ejection lip geometry on film cooling effectiveness and heat transfer[J]. Heat Transfer Research, 2010, 41(8):849-865.
[10] HORBACH T, SCHULZ A, BAUER H J. Trailing edge film cooling of gas turbine airfoils-External cooling performance of various internal pin fin configurations[J]. Journal of Turbomachinery, 2011, 133(4):041006.
[11] 魏建生, 朱惠人, 张丽, 等. 涡轮叶片尾缘劈缝气膜冷却特性实验研究[J]. 工程热物理学报, 2016, 37(9):1988-1993. WEI J S, ZHU H R, ZHANG L, et al. Experimental investigation on the film cooling characteristics of turbine blade trailing edge cutback[J]. Journal of Engineering Thermophysics, 2016, 37(9):1988-1993(in Chinese).
[12] 王瑞琴, 晏鑫, 何坤. 带肋板尾缘开缝叶片内的流动传热性能研究[J]. 西安交通大学学报, 2020, 54(1):150-161,183. WANG R Q, YAN X, HE K. Investigations of flow and heat transfer performance in a blade with trailing-edge cutback and lands[J]. Journal of Xi'an Jiaotong University, 2020, 54(1):150-161,183(in Chinese).
[13] YUAN H P, ZHU H R, KONG M Z. Effects of blowing ratio measured by liquid crystal on heat transfer characteristics of trailing edge cutback[J]. Chinese Journal of Aeronautics, 2008, 21(6):488-495.
[14] YANG Z F, HU H. An experimental investigation on the trailing edge cooling of turbine blades[J]. Propulsion and Power Research, 2012, 1(1):36-47.
[15] 郭之强, 郑梅, 董威, 等. 表面凸起对机翼热气防冰腔内换热强化的影响[J]. 航空学报, 2017, 38(2):520718. GUO Z Q, ZHENG M, DONG W, et al. Influence of surface convex on heat transfer enhancement of wing hot air anti-icing system[J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(2):520718(in Chinese).
[16] HUANG K N, ZHANG J Z, TAN X M, et al. Experimental study on film cooling performance of imperfect holes[J]. Chinese Journal of Aeronautics, 2018, 31(6):1215-1221.
[17] ZHANG J Z, ZHANG S C, WANG C H, et al. Recent advances in film cooling enhancement:A review[J]. Chinese Journal of Aeronautics, 2020, 33(4):1119-1136.
[18] KRUECKELS J, GRITSCH M, SCHNIEDER M. Design considerations and validation of trailing edge pressure side bleed cooling:GT2009-59161[R]. New York:ASME, 2009.
[19] 杨世铭, 陶文铨. 传热学[M]. 4版. 北京:高等教育出版社, 2006:229-243. YANG S M, TAO W Q. Heat transfer[M]. 4th ed. Beijing:Higher Education Press, 2006:229-243(in Chinese).
[20] 陈大为, 朱惠人, 李华太, 等. 尾迹对涡轮动叶全表面气膜冷却效率的影响[J]. 航空学报, 2019, 40(3):122651. CHEN D W, ZHU H R, LI H T, et al. Effect of unsteady wake on full coverage film cooling effectiveness for a turbine blade[J]. Acta Aeronautica et Astronautica Sinica, 2019, 40(3):122651(in Chinese).
[21] 刘存良, 朱惠人, 白江涛, 等. 基于瞬态液晶测量技术的收缩-扩张形孔气膜冷却特性[J]. 航空学报, 2009, 30(5):812-818. LIU C L, ZHU H R, BAI J T, et al. Film cooling characteristics of converging-expanding hole with transient liquid crystal measurement technique[J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(5):812-818(in Chinese).
[22] YE L, LIU C L, ZHOU D E, et al. Experimental and numerical investigations on the heat transfer of film cooling with cylindrical holes fed with internal coolant cross flows[J]. Journal of Heat Transfer, 2020, 142(5):052302.
[23] 叶林, 刘存良, 杨寓全. 直肋对扩张型尾缘半劈缝气膜冷却特性影响的实验研究[J]. 推进技术,2020, 41(9):2077-2087. YE L, LIU C L, YANG Y Q. Experimental investigation of effects of straight ribs on film cooling performance of expanded cutback surface for trailing-edge[J]. Journal of Propulsion Technology, 2020, 41(9):2077-2087(in Chinese).
[24] KAYS W, CRAWFORD M. Convective heat and mass transfer[M]. 3rd ed. New York:McGraw-Hill,1993:316.
[25] HOLLOWAY D S, LEYLEK J H, BUCK F A. Pressure-side bleed film cooling:Part II-Unsteady framework for experimental and computational results:GT2002-30472[R]. New York:ASME, 2002.
[26] MURATA A, YANO K, HANAI M, et al. Arrangement effects of inclined teardrop-shaped dimples on film cooling performance of dimpled cutback surface at airfoil trailing edge[J]. International Journal of Heat and Mass Transfer, 2017, 107:761-770.
[27] MURATA A, NISHIDA S, SAITO H, et al. Effects of surface geometry on film cooling performance at airfoil trailing edge:GT2011-45355[R]. New York:ASME, 2011.

Effect of V-shaped ribs on film cooling characteristics of trailing-edge cutback

RichHTML

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Ming REN, Cunliang LIU, Kun DU, Li ZHANG, Huiren ZHU, Bolun ZHANG. Film cooling with compound angle holes in leading edge of twisted turbine blade [J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(18): 128315-128315.
[2]	WANG Bin, WANG Haitao, WANG Yufeng, ZHANG Wenwu. Water-assisted laser scanning machining test of thermal barrier coating [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525353-525353.
[3]	YE Lin, LIU Cunliang, ZHU Andong, ZHOU Tianliang. Influence of compact-ribbed passage on trailing-edge cutback film cooling performance [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(3): 125174-125174.
[4]	XIA Kailong, HE Qing, ZHANG Yusheng. Measurement method of turbine blade film aperture based on infrared thermal imaging and shrinkage law [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(12): 426271-426271.
[5]	LUO Shibin, MIAO Zhichao, SONG Jiawen. Influencing factors of active cooling at leading edge of hypersonic vehicles [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(12): 627023-627023.
[6]	YANG Yuquan, LIU Cunliang, ZHANG Jie, HUANG Rong. Effect of mass flow ratios on film cooling characteristics of endwall: Experimental study [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(7): 124399-124399.
[7]	WANG Jin, SUN Jie, ZHAO Zhanming, ZHANG Bo, REN Xiaodong, XIE Gongnan. Research on film cooling performance of sister hole based on structural parameter analysis [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(7): 124775-124775.
[8]	LI Zuobiao, WEN Fengbo, TANG Xiaolei, SU Liangjun, WANG Songtao. Prediction of single-row hole film cooling performance based on deep learning [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(4): 524331-524331.
[9]	ZHAO Yuanyuan, ZENG Fei, LI Yang, GAN Mingyu, SHI Shengxian. 3D measurement technique for film cooling holes based on light-field imaging [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(10): 524158-524158.
[10]	TANG Liang, HU Jinhua, LIU Jiwu, LI Ping, ZHOU Lixin, YANG Baoe. Experimental study on oblique jet wall impingement and geometrical parameter modeling of liquid film [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(12): 124061-124061.
[11]	CHEN Dawei, ZHU Huiren, LI Huatai, LIU Haiyong, ZHOU Daoen. Effect of unsteady wake on full coverage film cooling effectiveness for a turbine blade [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2019, 40(3): 122651-122651.
[12]	ZHANG Zhuoyuan, HUANG Shizhang, GAO Xiaowei. Numerical simulation of heat transfer of n-decane under supercritical pressure in horizontal rectangular cooling channels [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(12): 122297-122297.
[13]	ZHU Peiyuan, SONG Liming, LI Jun, FENG Zhenping. Effects of location and geometry of slot on film cooling performance of end-wall [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(9): 520942-520942.
[14]	HUANG Shizhang, RUAN Bo, GAO Xiaowei. Numerical investigation of heat transfer enhancement of cryogenic-propellant methane in corrugated tubes at supercritical pressures [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(5): 120515-120515.
[15]	ZHANG Jingzhou, WANG Xu, SHAN Yong. Effects of plug rear-body film cooling on infrared radiation and aerodynamic performance of axisymmetric plug nozzle [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2015, 36(8): 2601-2608.