切深对椭圆超声振动切削机理的影响

doi:10.7527/S1000-6893.2016.0231

Abstract

Abstract:

The influence of the depth of cut on the elliptical ultrasonic vibration cutting mechanism is analyzed through theoretical model, finite element simulation and cutting experiment. It is found that when the depth of cut is small, the influence of the rounded cutting edge must be taken into consideration, and the cutting process reveals the micro-machining characteristics. The kinematics model and dynamics model for orthogonal elliptical ultrasonic vibration cutting are established based on the micro-machining theory. In the proposed models, the cutting tool is firstly divided into four cutting zones:the elastic recovery zone on the flank face, the ploughing zone on the rounded cutting edge, the shearing zone on the rounded cutting edge, and tool-chip friction zone on the rake face. The cutting force in each zone is then calculated. Finite element simulations of the cutting process and cutting experiments are also conducted. Simulation results show that when the depth of cut is less than the minimum cutting thickness, the cutting process is dominated by elastic recovery and friction on the flank face and ploughing of the rounded cutting edge, without chip generation, with the thrust cutting force being greater than the principal cutting force. However, when the depth of cut exceeds the minimum cutting thickness and keeps increasing, the effects of rounded cutting edge shearing and tool-chip friction on the rake face gradually take the dominant place during the cutting process, while the principal cutting force exceeds the thrust cutting force and increases rapidly.

Key words: elliptical ultrasonic vibration, depth of cut, rounded cutting edge, micro-machining, minimum cutting thickness

CLC Number:

V261.92

ZHANG Xiangyu, ZHANG Deyuan, SUI He, JIANG Xinggang. Influence of depth of cut on elliptical ultrasonic vibration cutting mechanism[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(4): 420567-420567.

References

[1] MORIWAKI T, SHAMOTO E. Ultrasonic elliptical vibration cutting[J]. Annals of the CIRP-Manufacturing Technology, 1995, 44(13):31-34.
[2] PATIL S, JOSHI S, TEWARI A, et al. Modeling and simulation of effect of ultrasonic vibrations on machining of Ti6Al4V[J]. Ultrasonics, 2014, 54(2):694-705.
[3] XU W, ZHANG L. Ultrasonic vibration-assisted machining:principle, design and application[J]. Advances in Manufacturing, 2015, 3(3):173-192.
[4] MA C X, SHAMOTO E, MORIWAKI T. Study on the thrust cutting force in ultrasonic elliptical vibration cutting[J]. Materials Science Forum, 2004, 471-472:396-400.
[5] 季远, 李勋, 张德远, 等. 超声椭圆振动精密切削[J]. 航空制造技术, 2005(4):92-95. JI Y, LI X, ZHANG D Y, et al. Precision ultrasonic elliptical vibration cutting[J]. Aeronautical Manufacturing Technology, 2005(4):92-95 (in Chinese).
[6] 隋翯, 张德远, 陈华伟, 等. 超声振动切削对耦合颤振的影响[J]. 航空学报, 2016, 37(5):1696-1704. SUI H, ZHANG D Y, CHEN H W, et al. Influence of ultrasonic vibration cutting on mode-coupling chatter[J]. Acta Aeronautica et Astronautica Sinica, 2016, 37(5):1696-1704 (in Chinese).
[7] ZHANG X Q, LIU K, KUMAR A, et al. A study of the diamond tool wear suppression mechanism in vibration-assisted machining of steel[J]. Journal of Materials Processing Technology, 2014, 214(2):496-506.
[8] SHAMOTO E, MORIWAKI T. Study on elliptical vibration cutting[J]. Annals of CIRP-Manufacturing Technology, 1994, 43(1):35-38.
[9] SHAMOTO E, SUZUKI N, HINO R. Analysis of 3D elliptical vibration cutting with thin shear plane model[J]. Annals of CIRP-Manufacturing Technology, 2008, 57(1):57-60.
[10] ZHANG X Q, KUMAR A, RAHMAN M, et al. An analytical force model for orthogonal elliptical vibration cutting technique[J]. Journal of Manufacturing Processes, 2012, 14(3):378-387.
[11] NATEGH M J, RAZAVI H, ABDULLAH A. Analytical modeling and experimental investigation of ultrasonic-vibration assisted oblique turning, Part I:Kinematics analysis[J]. International Journal of Mechanical Sciences, 2012, 63(1):1-11.
[12] RAZAVI H, NATEGH M J, ABDULLAH A. Analytical modeling and experimental investigation of ultrasonic-vibration assisted oblique turning, Part Ⅱ:Dynamics analysis[J]. International Journal of Mechanical Sciences, 2012, 63(1):12-25.
[13] 于海鹏. 基于有限元法的椭圆振动切削机理研究[D]. 北京:北京化工大学, 2014:11-36. YU H P. Research on elliptical vibration cutting mechanism based on finite element method[D]. Beijing:Beijing University of Chemical Technology, 2014:11-36 (in Chinese).
[14] BAI W, SUN R L, GAO Y, et al. Analysis and modeling of force in orthogonal elliptical vibration cutting[J]. International Journal of Advanced Manufacturing Technology, 2015, 83(5):1-12.
[15] 杨毅青, 张斌, 刘强. 铣削建模中多种切削力模型的分析比较[J]. 振动工程学报, 2015, 28(1):82-90. YANG Y Q, ZHANG B, LIU Q. Analysis and comparison of various cutting force models in the milling process simulation[J]. Journal of Vibration Engineering, 2015, 28(1):82-90 (in Chinese).
[16] KIM J D, KIM D S. Theoretical analysis of micro-cutting characteristics in ultra-precision machining[J]. Journal of Materials Processing Technology, 1995, 49(3):387-398.
[17] BREHL D E, DOW T A. Review of vibration-assisted machining[J]. Precision Engineering, 2008, 32(3):153-172.
[18] 方瑞. 微细车铣切削力建模及切削试验研究[D]. 沈阳:沈阳理工大学, 2013:11-48. FANG R. Research on cutting forces modeling and test of micro turn-milling[D]. Shenyang:Shenyang Ligong University, 2013:11-48 (in Chinese).
[19] 石文天. 微细切削技术[M]. 北京:机械工业出版社, 2011:36-60. SHI W T. Micro machining technology[M]. Beijing:China Machine Press, 2011:36-60 (in Chinese).
[20] SON S M, LIM H S, AHN J H. Effects of the friction coefficient on the minimum cutting thickness in micro cutting[J]. International Journal of Machine Tools and Manufacture, 2005, 45(4-5):529-535.
[21] OXLEY P L B, HASTINGS W F. Minimum work as a possible criterion for determining the frictional conditions at the tool/chip interface in machining[J]. Philosophical Transactions of the Royal Society B Biological Sciences, 1976, 282(3):565-584.
[22] ANAND R S, PATRA K. Modeling and simulation of mechanical micro-machining-a review[J]. Machining Science and Technology, 2014, 18(3):323-347.
[23] 柳柏魁, 林正英. 基于Deform-3D钻削加工三维有限元仿真[J]. 工具技术, 2015, 49(7):43-47. LIU B K, LIN Z Y. Three dimensional FEM simulation of drilling based on software Defrom-3D[J]. Tool Engineering, 2015, 49(7):43-47 (in Chinese).
[24] 张蓉蓉, 赵先锋, 李长虹, 等. 基于Deform-3D的铝合金7075车削力模型的研究[J]. 组合机床与自动化加工技术, 2016(6):59-62. ZHANG R R, ZHAO X F, LI C H, et al. Analysis of the cutting force modeling of aluminum alloy 7075 based on Deform-3D[J]. Modular Machine Tool & Automatic Manufacturing Technique, 2016(6):59-62 (in Chinese).

Influence of depth of cut on elliptical ultrasonic vibration cutting mechanism

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 4

Recommended Articles

Metrics

Comments

[1]	Yiwen LI, Zhaohui DEND, Tao LIU, Rongjin ZHUO, Zhongyang LI, Lishu LV. Review on on⁃line monitoring of chatter in cutting process [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2023, 44(11): 27562-027562.
[2]	SUI He, ZHANG Deyuan, CHEN Huawei, ZHANG Xiangyu. Influence of ultrasonic vibration cutting on mode-coupling chatter [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2016, 37(5): 1696-1704.
[3]	LI Wen, YIN Jiao, LV Leiping, XU Minggang, ZHANG Deyuan. Study on the Unseparated Ultrasonic Elliptical Vibration Cutting Force [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2013, 34(9): 2241-2248.
[4]	PENG Zhenlong, ZHANG Xiangyu, ZHANG Deyuan. High-speed ultrasonic vibration cutting for difficult-to-machine materials in aerospace field [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525587-525587.