临界反应距离法微细电化学高效加工大长径比微电极

doi:10.7527/S1000-6893.2021.25339

论文

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

临界反应距离法微细电化学高效加工大长径比微电极

彭子龙, 刘聪, 李一楠, 兰红波

1. 青岛理工大学山东省增材制造工程技术研究中心, 青岛 266520 2. 青岛理工大学工业流体节能与污染控制教育部重点实验室, 青岛 266520

收稿日期:2021-01-28 修回日期:2021-03-01 出版日期:2022-04-15 发布日期:2021-06-29
通讯作者: 彭子龙 E-mail:pengzilong@qut.edu.cn
基金资助:
国家自然科学基金（51875300，51871128）；山东省自然科学基金重大基础研究项目（ZR2020ZD04）；山东省自然科学基金（ZR2017MEE012，ZR2018MEE017）

Micro electrical chemical machining for efficient fabricating large aspect ratio micro electrodes by critical gap method

PENG Zilong, LIU Cong, LI Yinan, LAN Hongbo

1. Shandong Engineering Research Center for Additive Manufacturing, Qingdao University of Technology, Qingdao 266520, China 2. Key Lab of Industrial Fluid Energy Conservation and Pollution Control, Ministry of Education, Qingdao University of Technology, Qingdao 266520, China

Received:2021-01-28 Revised:2021-03-01 Online:2022-04-15 Published:2021-06-29
Supported by:
National Natural Science Foundation of China (51875300, 51871128); Major Project of Shandong Province Natural Science Foundation (ZR2020ZD04); Shandong Province Natural Science Foundation (ZR2017MEE012, ZR2018MEE017)

摘要/Abstract

摘要： 提出了一种基于临界反应距离控制的微细电化学（μ-ECM）在线高效制备大长径比微电极方法，旨在解决大长径比微电极制备难题。采用强碱性电解液及微秒级电源，实现了钨电极的微米级精度可控去除。分析了微细电化学加工材料去除微观过程，仿真分析了两极距离变化条件下间隙电流密度变化，确定了基于临界反应距离精确控制材料去除的参数选择范围。建立了电极材料蚀除过程数学模型，得到了材料蚀除量的变化规律。进行了系统的工艺实验，研究了电压、脉宽、电解液浓度对微细电极材料去除率的影响规律。采用优化的工艺参数，得到了直径10 μm、长径比大于200的微细电极，材料去除率最高可达2.7×10^-2 mm³/min，加工效率较目前主流方法提高一个数量级。

关键词: 临界反应距离, 微细电化学, 微电极, 大长径比, 高效去除

Abstract: A micro Electrical Chemical Machining (μ-ECM) method based on critical gap control for efficient fabricating micro electrodes with large aspect ratio was proposed. Using strong alkaline electrolyte and microsecond power supply, the micron level precise removal of tungsten electrode can be controlled. The micro process of material removal in μ-ECM was analyzed. The process parameters for precise control of material removal based on critical gap have been determined by simulating the gap current density of different gap distance. The mathematical model of electrode material removal process was established, and the material removal law was obtained. The effects of gap voltage, pulse width and electrolyte concentration on the removal rate of micro electrode materials were studied. As a result, a micro electrode with diameter of 10 μm and aspect ratio of more than 200 was obtained by using the optimized process parameters. The maximum material removal rate can reach 2.7×10^-2 mm³/min, which is an order of magnitude higher than the current other methods.

Key words: critical reaction gap, μ-ECM, micro electrode, large aspect ratio, efficient fabrication

中图分类号:

V216.5/TG662

彭子龙, 刘聪, 李一楠, 兰红波. 临界反应距离法微细电化学高效加工大长径比微电极[J]. 航空学报, 2022, 43(4): 525339-525339.

PENG Zilong, LIU Cong, LI Yinan, LAN Hongbo. Micro electrical chemical machining for efficient fabricating large aspect ratio micro electrodes by critical gap method[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2022, 43(4): 525339-525339.

参考文献

[1] EPSTEIN A H, SENTURIA S D, ANATHASURESH G, et al. Power MEMS and microengines[C]//Proceedings of International Solid State Sensors and Actuators Conference. Piscataway:IEEE Press, 1997:753-756.
[2] EPSTEIN A H. Millimeter-scale, micro-electro-mechanical systems gas turbine engines[J]. Journal of Engineering for Gas Turbines and Power, 2004, 126(2):205-226.
[3] DONG Y H, WANG Z L, PENG Z L, et al. Design and fabrication of the micro turbine for micro gas turbine engine[J]. Advanced Materials Research, 2009, 69-70:530-534.
[4] QI X X, FANG X L, ZHU D. Investigation of electrochemical micromachining of tungsten microtools[J]. International Journal of Refractory Metals and Hard Materials, 2018, 71:307-314.
[5] LIU Y, ZHU D, ZENG Y B, et al. Experimental investigation on complex structures machining by electrochemical micromachining technology[J]. Chinese Journal of Aeronautics, 2010, 23(5):578-584.
[6] 张明君, 殷国富, 袁光辉. 大长径比微细轴的车削工艺研究[J]. 机械工程学报, 2005, 41(2):137-141. ZHANG M J, YIN G F, YUAN G H. Study on turning technics of big diameter-length rate micro-shaft[J]. Journal of Mechanical Engineering, 2005, 41(2):137-141(in Chinese).
[7] OHMORI H, KATAHIRA K, NARUSE T, et al. Microscopic grinding effects on fabrication of ultra-fine micro tools[J]. CIRP Annals, 2007, 56(1):569-572.
[8] YAMAZAKI M, SUZUKI T, MORI N, et al. EDM of micro-rods by self-drilled holes[J]. Journal of Materials Processing Technology, 2004, 149(1-3):134-138.
[9] TAKEZAWA H, HAMAMATSU H, MOHRI N, et al. Development of micro-EDM-center with rapidly sharpened electrode[J]. Journal of Materials Processing Technology, 2004, 149(1-3):112-116.
[10] 王振龙, 朱保国, 田锡清. 气体介质中深小孔电火花加工技术研究[J]. 航空学报, 2007, 28(2):460-463. WANG Z L, ZHU B G, TIAN X Q. Research on dry EDM for deep and small holes[J]. Acta Aeronautica et Astronautica Sinica, 2007, 28(2):460-463(in Chinese).
[11] PATRO S K, MISHRA D K, ARAB J, et al. Numerical and experimental analysis of high-aspect-ratio micro-tool electrode fabrication using controlled electrochemical machining[J]. Journal of Applied Electrochemistry, 2020, 50(2):169-184.
[12] HAN W, KUNIEDA M. Fabrication of tungsten micro-rods by ECM using ultra-short-pulse bipolar current[J]. CIRP Annals, 2017, 66(1):193-196.
[13] LU Z N, YONEYAMA T. Micro cutting in the micro lathe turning system[J]. International Journal of Machine Tools and Manufacture, 1999, 39(7):1171-1183.
[14] ONIKURA H, OHNISHI O, TAKE Y, et al. Fabrication of micro carbide tools by ultrasonic vibration grinding[J]. CIRP Annals, 2000, 49(1):257-260.
[15] XU W X, WU Y B. A novel approach to fabricate high aspect ratio micro-rod using ultrasonic vibration-assisted centreless grinding[J]. International Journal of Mechanical Sciences, 2018, 141:21-30.
[16] MASUZAWA T, FUJINO M, KOBAYASHI K, et al. Wire electro-discharge grinding for micro-machining[J]. CIRP Annals, 1985, 34(1):431-434.
[17] SINGH A K, PATOWARI P K, DESHPANDE N V. Experimental analysis of reverse micro-EDM for machining microtool[J]. Materials and Manufacturing Processes, 2016, 31(4):530-540.
[18] YIN Q F, WANG X Q, WANG P, et al. Fabrication of micro rod electrode by electrical discharge grinding using two block electrodes[J]. Journal of Materials Processing Technology, 2016, 234:143-149.
[19] LIM Y M, KIM S H. An electrochemical fabrication method for extremely thin cylindrical micropin[J]. International Journal of Machine Tools and Manufacture, 2001, 41(15):2287-2296.
[20] LIM H J, LIM Y M, KIM S H. Fabrication of arbitrarily shaped microelectrodes by electrochemical etching[J]. Japanese Journal of Applied Physics, 2003, 42(3):1479-1485.
[21] HAN W, KUNIEDA M. Wire electrochemical grinding of tungsten micro-rods using neutral electrolyte[J]. Precision Engineering, 2018, 52:458-468.
[22] MATHEW R, SUNDARAM M M. Modeling and fabrication of micro tools by pulsed electrochemical machining[J]. Journal of Materials Processing Technology, 2012, 212(7):1567-1572.
[23] 刘勇, 朱荻, 曾永彬, 等. 微细电解铣削加工模型及实验研究[J]. 航空学报, 2010, 31(9):1864-1871. LIU Y, ZHU D, ZENG Y B, et al. Theoretical and experimental research on micro electrochemical milling[J]. Acta Aeronautica et Astronautica Sinica, 2010, 31(9):1864-1871(in Chinese).
[24] NGUYEN M D, RAHMAN M, WONG Y S. Modeling of radial gap formed by material dissolution in simultaneous micro-EDM and micro-ECM drilling using deionized water[J]. International Journal of Machine Tools and Manufacture, 2013, 66:95-101.
[25] 李名鸿, 刘勇, 郭春生, 等. 高回转精度微柱状电极电化学加工模型及试验[J]. 航空学报, 2016, 37(12):3864-3872. LI M H, LIU Y, GUO C S, et al. Model and experimental on fabrication of cylindrical micro electrode with high rotation accuracy by electrochemical machining[J]. Acta Aeronautica et Astronautica Sinica, 2016, 37(12):3864-3872(in Chinese).
[26] GU M C, ZENG Y B, MENG L C. Electrochemical micromachining of square holes in stainless steel in H₂SO₄[J]. International Journal of Electrochemical Science, 2019,14:414-426.
[27] AHN S H, RYU S H, CHOI D K, et al. Electro-chemical micro drilling using ultra short pulses[J]. Precision Engineering, 2004, 28(2):129-134.
[28] 李小海, 王振龙, 赵万生. 高频窄脉冲电流微细电解加工[J]. 机械工程学报, 2006, 42(1):162-167. LI X H, WANG Z L, ZHAO W S. Electrolytic micromachining with high frequency short pulse current[J]. Journal of Mechanical Engineering, 2006, 42(1):162-167(in Chinese).
[29] LI Y, ZHENG Y F, YANG G, et al. Localized electrochemical micromachining with gap control[J]. Sensors and Actuators A:Physical, 2003, 108(1-3):144-148.
[30] ZENG Z Q, WANG Y K, WANG Z L, et al. A study of micro-EDM and micro-ECM combined milling for 3D metallic micro-structures[J]. Precision Engineering, 2012, 36(3):500-509.
[31] RAVI N, CHUAN S X. The effects of electro-discharge machining block electrode method for microelectrode machining[J]. Journal of Micromechanics and Microengineering, 2002, 12(5):532-540.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

临界反应距离法微细电化学高效加工大长径比微电极

Micro electrical chemical machining for efficient fabricating large aspect ratio micro electrodes by critical gap method

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 0

编辑推荐

Metrics

本文评价