锯齿扁管内沸腾换热试验

doi:10.7527/S1000-6893.2016.0248

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

锯齿扁管内沸腾换热试验

詹宏波, 文涛, 张大林

南京航空航天大学航空宇航学院, 南京 210016

收稿日期:2016-04-19 修回日期:2016-08-31 出版日期:2017-03-15 发布日期:2016-09-28
通讯作者: 张大林,E-mail:zhangdalin@nuaa.edu.cn E-mail:zhangdalin@nuaa.edu.cn

Test of boiling heat transfer in rectangular channels with offset fins

ZHAN Hongbo, WEN Tao, ZHANG Dalin

College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Received:2016-04-19 Revised:2016-08-31 Online:2017-03-15 Published:2016-09-28

摘要/Abstract

摘要：

建立以等热流密度方式进行试验件加热的沸腾换热试验系统，分别对当量直径为1.28 mm和1.59 mm锯齿扁管内R134a工质的沸腾换热特性进行研究，试验参数范围：制冷剂质量流率为68.5~305.5 kg/（m²·s），工作饱和压力为0.27~0.46 MPa，加热热流密度为9~42 kW/m²。试验结果表明：相同结构的通道，当量直径小换热能力更强；热流密度和饱和压力对沸腾换热的影响与一个干度值有关。当干度小于此值时，沸腾换热系数会随着热流密度及饱和压力增大而增大；而当干度大于此值时，沸腾换热系数随着干度增大而急剧下降，热流密度和饱和压力对换热的影响较小；该干度值会随着热流密度或饱和压力增大而逐渐变小。质量流率对沸腾换热的影响与热流密度有关，随着热流密度增大，质量流率的影响趋向大干度区域。通过分析各参数对沸腾换热的影响，建立了一个预测试验工况下微小尺寸锯齿扁管的沸腾换热系数计算经验公式。

关键词: 沸腾, 换热, 两相流, 制冷剂R134a, 锯齿扁管

Abstract:

A boiling heat transfer test system is built to investigate the boiling heat transfer characteristics of two kinds of rectangular channels with offset fins,with R134a as the working medium. The hydraulic diameters of the channels are 1.28 mm and 1.59 mm. The experiments are performed at mass flow rate of refrigerant between 68.5 and 305.5 kg/(m²·s), heat flux between 9 and 42 kW/m², and saturation pressure between 0.27 and 0.45 MPa, with constant heat flux heating mode. The results show that the channel with smaller hydraulic diameter has stronger heat transfer capability. The influences of heat flux and saturation pressure on boiling heat transfer are related to a value of vapor quality. If the vapor quality is less than this value, the increase of heat flux or saturation pressure would lead to the increase of heat transfer coefficients. If the vapor quality is greater than this value, the boiling heat transfer coefficient will sharply decrease with the increase of vapor quality, and the influences of heat flux and saturation pressure will be much weaker. The value will gradually decrease with the increase of heat flux or saturation pressure. The effect of mass flow rate on boiling heat transfer is related to heat flux. With the increase of heat flux, the influence of mass flow rate tends to the region with greater vapor quality. On the basis of the analysis of these parameters, a new correlation is proposed to predict the boiling heat transfer coefficients of the small sized channels with offset fins under the experimental conditions.

Key words: flow boiling, heat transfer, two-phase flow, refrigerant R134a, rectangular channel with offset fins

中图分类号:

V231.1
TK124

詹宏波, 文涛, 张大林. 锯齿扁管内沸腾换热试验[J]. 航空学报, 2017, 38(3): 120329-120329.

ZHAN Hongbo, WEN Tao, ZHANG Dalin. Test of boiling heat transfer in rectangular channels with offset fins[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017, 38(3): 120329-120329.

参考文献

[1] OH J T, PAMITRAN A S, CHOI K I, et al. Experimental investigation on two-phase flow boiling heat transfer of five refrigerants in horizontal small tubes of 0.5, 1.5 and 3.0 mm inner diameters[J]. International Journal of Heat & Mass Transfer, 2011, 54(s 9-10):2080-2088.
[2] COPETTI J B, MACAGNAN M H, ZINANI F, et al. Flow boiling heat transfer and pressure drop of R-134a in a mini tube:an experimental investigation[J]. Experimental Thermal & Fluid Science, 2011, 35(4):636-644.
[3] TIBIRICA C B, RIBATSKI G. Flow boiling heat transfer of R134a and R245fa in a 2.3 mm tube[J]. International Journal of Heat & Mass Transfer, 2010, 53(s 11-12):2459-2468.
[4] SHIFERAW D, KARAYIANNISS T G, KENNING D B R. Flow boiling in a 1.1 mm tube with R134a:Experimental results and comparison with model[J]. International Journal of Thermal Sciences, 2009, 48(2):331-341.
[5] 余建祖. 换热器原理与设计[M]. 北京:北京航空航天大学出版社, 2006:43-44. YU J Z. Principle and design of heat exchanger[M]. Beijing:Beihang University Press, 2006:43-44(in Chinese).
[6] DUBROVSKY E V, VASILIEV V Y. Enhancement of convective heat transfer in rectangular ducts of interrupted surfaces[J]. International Journal of Heat & Mass Transfer, 1988, 31(4):807-818.
[7] MOCHIZUKI S, YAGI Y, YANG W J. Transport phenomena in stacks of interrupted parallel-plate surfaces[J]. Experimental Heat Transfer, 1987, 1(2):127-140.
[8] MANGLIK R M, BERGLES A E. Heat transfer and pressure drop correlations for the rectangular offset strip fin compact heat exchanger[J]. Experimental Thermal & Fluid Science, 1995, 10(2):171-180.
[9] PULVIRENTI B, MATALONE A, BARUCCA U. Boiling heat transfer in narrow channels with offset strip fins:Application to electronic chipsets cooling[J]. Applied Thermal Engineering, 2010, 30(s 14-15):2138-2145.
[10] KIM B, SOHN B. An experimental study of flow boiling in a rectangular channel with offset strip fins[J]. International Journal of Heat & Fluid Flow, 2006, 27(3):514-521.
[11] CHOI K I, PAMITRAN A S, OH C Y, et al. Boiling heat transfer of R-22, R-134a, and CO₂ in horizontal smooth minichannels[J]. International Journal of Refrigeration, 2007, 30(8):1336-1346.
[12] YEN T H, KASAGI N, SUZUKI Y. Forced convective boiling heat transfer in microtubes at low mass and heat fluxes[J]. International Journal of Multiphase Flow, 2003, 29(12):1771-1792.
[13] BERTSCH S S, GROLL E A, GARIMELLA S V. Effects of heat flux, mass flux, vapor quality, and saturation temperature on flow boiling heat transfer in microchannels[J]. International Journal of Multiphase Flow, 2009, 35(2):142-154.
[14] VAKILI-FARAHANI F, AGOSTINI B, THOME J R. Experimental study on flow boiling heat transfer ofmultiport tubes with R245fa and R1234ze(E)[J]. International Journal of Refrigeration, 2013, 36(2):335-352.
[15] BERTSCH S S, GROLL E A, GARIMELLA S V. A composite heat transfer correlation for saturated flow boiling in small channels[J]. International Journal of Heat & Mass Transfer, 2009, 52(7-8):2110-2118.
[16] 凯斯W M, 伦敦A L. 紧凑式热交换器[M]. 北京:科技出版社, 1997:285-326. KAYS W M, LONDON A L. Compact heat exchangers[M]. Beijing:Science and Technology Press, 1997:285-326(in Chinese).
[17] FELDMAN A, MARVILLET C, LEBOUCHE M. Nucleate and convective boiling in plate fin heat exchangers[J]. International Journal of Heat & Mass Transfer, 2000, 43(18):3433-3442.
[18] LIU Z, WINTERTON R H S. A general correlation for saturated and subcooled flow boiling in tubes and annuli, based on a nucleate pool boiling equation[J]. International Journal of Heat & Mass Transfer, 1991, 34(11):2759-2766.
[19] KEW P A, CORNWELL K. Correlations for the prediction of boiling heat transfer in small-diameter channels[J]. Applied Thermal Engineering, 1997, 17(8-10):705-715.
[20] FANG X. A new correlation of flow boiling heat transfer coefficients based on R134a data[J]. International Journal of Heat & Mass Transfer, 2013, 66(6):279-283.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

锯齿扁管内沸腾换热试验

Test of boiling heat transfer in rectangular channels with offset fins

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	韦宏, 王鹏, 董威, 郭晓峰, 李治达, 杨学森, 唐中富, 付超. 主流速度对微细管式预冷器结霜和抑霜特性的影响[J]. 航空学报, 2024, 45(2): 128639-128639.
[2]	李勐, 陈星伊, 陈吉昌, 吴彬, 童明波. 波浪情况下民机水上迫降性能数值分析[J]. 航空学报, 2024, 45(2): 28-43.
[3]	董彦钊, 周延, 邹继贤, 王信, 李晓冬, 崔洪帅. 试车台供气压缩机组并网控制方法[J]. 航空学报, 2023, 44(9): 327221-327221.
[4]	张国渊, 黎旭康, 赵伟刚, 赵洋洋, 王俊倩. 低温高速动静结合型机械密封两相流仿真与实验[J]. 航空学报, 2023, 44(23): 628229-628229.
[5]	李泓瑾, 李军伟, 谢侃, 李想, 杨正, 王宁飞. 两相流对固体火箭发动机塞式喷管性能的影响[J]. 航空学报, 2023, 44(16): 127890-127890.
[6]	王子豪, 杜家磊, 梁国柱, 王浩泽, 蔡震宇, 马晓秋. 大温差下印刷电路板式换热器起动过程建模与实验[J]. 航空学报, 2023, 44(16): 127893-127893.
[7]	郑梅, 冯丽娟, 秦娜, 尹金鸽. 短舱防冰系统三维内外流耦合计算方法[J]. 航空学报, 2023, 44(1): 627425-627425.
[8]	安利平, 王昊, 王掩刚, 朱自环. 跨声速压气机湿压缩性能及流动特性[J]. 航空学报, 2022, 43(9): 126024-126024.
[9]	马世赫, 李志超, 刘桂贤, 张永俊, 王瑞祥. 脉冲气体辅助掩模电解加工技术[J]. 航空学报, 2022, 43(4): 525646-525646.
[10]	叶青, 饶炜, 刘锋, 孙泽洲, 刘国强, 王闯, 董捷, 韩泉东, 缪远明, 谭志云, 陆慧林. 火星着陆发动机羽流与火壤的相互作用[J]. 航空学报, 2022, 43(3): 626557-626557.
[11]	吕亚国, 姜乐, 高晓果, 刘振侠, 朱鹏飞, 高文君. 高速轴承环下润滑收油叶片结构参数与工况参数间的匹配关系[J]. 航空学报, 2022, 43(12): 426037-426037.
[12]	吕元伟, 张靖周, 单勇, 孙文静. 冠齿喷管射流冲击半圆形靶面的对流换热[J]. 航空学报, 2021, 42(7): 124762-124762.
[13]	叶林, 刘存良, 杨寓全, 黄蓉, 朱安冬. V肋对尾缘劈缝气膜冷却特性的影响[J]. 航空学报, 2021, 42(6): 124181-124181.
[14]	童明波, 陈吉昌, 李乐, 肖天航, 古彪, 董登科, 汪正中. 飞行器水载荷结构完整性数值模拟现状与展望-Part I:水上迫降和水上漂浮[J]. 航空学报, 2021, 42(5): 524530-524530.
[15]	赵立杰, 田孟伟, 李景奎, 王明阳, 刘达. 水上电动飞机浮筒设计及起飞滑行[J]. 航空学报, 2021, 42(3): 624590-624590.