复合材料螺接性能的影响因素研究

doi:CNKI:11-1929/V.20111202.1031.002

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

复合材料螺接性能的影响因素研究

张岐良, 曹增强

西北工业大学机电学院,陕西西安 710072

收稿日期:2011-07-26 修回日期:2011-10-13 出版日期:2012-04-25 发布日期:2012-04-20
通讯作者: 曹增强 E-mail:czq66326@nwpu.edu.cn

Study on Factors Influencing the Performance of Composite Bolted Connections

ZHANG Qiliang, CAO Zengqiang

School of Mechanical Engineering, Northwestern Polytechnical University, Xi’an 710072, China

Received:2011-07-26 Revised:2011-10-13 Online:2012-04-25 Published:2012-04-20

摘要/Abstract

摘要： 利用有限元软件ANSYS建立了单钉双剪复合材料单拉接头的1/2模型,研究了钉孔配合、螺栓预紧力和接触面间摩擦对接头的强度等性能的影响。设计了若干实验,证明有限元模型是有效的,其计算误差控制在10%以内。有限元计算结果表明:小干涉量的过盈配合能极大地提高接头的强度,与3%间隙量相比,最优干涉量下接头强度可提高36.5%;适当的螺栓拧紧力矩也可提高接头的强度;接头中被连接板间的摩擦对接头强度也是有利的,但在一定接头尺寸条件下,摩擦力的增大有可能会改变接头的破坏模式。以上研究成果为复合材料多钉连接钉载分配均匀化的参数化分析提供了一个突破口,这也是本文后续研究的一个内容。

关键词: 复合材料, 螺栓连接, 有限元法, 干涉配合, 预紧力, 失效模式

Abstract: A double-lap single-bolt composite joint is designed as a model using the ANSYS finite element (FE) package. The joint is subjected to longitudinal tensile loads and half of the model is numerically analyzed. Three key factors influencing the performance of the connection are studied, including the bolt-hole fit, bolt pretightening force and the friction between the contacting plates. The model is then validated by several experiments, with computational errors of less than 10%. Analytical results show that a small magnitude of interference substantially improves the strength of the joints. With optimum interference, there is an increase of joint strength up to 36.5% as compared with the 3% clearance fit scenario. An adequate tightening torque also enhances the joint strength. The friction between the connecting laminates is also beneficial to increasing the strength. The failure mode varies with the friction coefficients between the plates for specific connection sizes. These findings signifies a beginning for the parametric analysis on load distribution uniformization in multi-bolted composite joints, which will be explored in subsequent studies.

Key words: composite material, bolted joint, finite element method, interference fit, pretightening force, failure mode

中图分类号:

张岐良, 曹增强. 复合材料螺接性能的影响因素研究[J]. 航空学报, 2012, (4): 755-762.

ZHANG Qiliang, CAO Zengqiang. Study on Factors Influencing the Performance of Composite Bolted Connections[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2012, (4): 755-762.

参考文献

[1] Chen S J. Composite technology and large aircraft. Acta Aeronautica et Astronautica Sinica, 2008, 29(3): 605-610.(in Chinese) 陈绍杰. 复合材料技术与大型飞机. 航空学报,2008, 29(3): 605-610.
[2] McCarthy M A, McCarthy C T, Lawlor V P, et al. Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints:Part I—model development and validation. Composite Structures, 2005, 71(2): 140-158.
[3] Ireman T. Three-dimensional stress analysis of bolted single-lap composite joints. Composite Structures, 1998, 43(3): 195-216.
[4] Thoppul S D, Finegan J, Gibson R F. Mechanics of mechanically fastened joints in polymer-matrix composite structures—a review. Composites Science and Technology, 2009, 69(3-4): 301-329.
[5] Hühne C, Zerbst A K, Kuhlmann G, et al. Progressive damage analysis of composite bolted joints with liquid shim layers using constant and continuous degradation models. Composite Structures, 2010, 92(2): 189-200.
[6] Park H J. Effects of stacking sequence and clamping force on the bearing strengths of mechanically fastened joints in composite laminates. Composite Structures, 2001, 53(2): 213-221.
[7] Park H J. Bearing failure analysis of mechanically fastened joints in composite laminates. Composite Structures, 2001, 53(2): 199-211.
[8] Kiral B G. Effect of the clearance and interference-fit on failure of the pin-loaded composites. Materials & Design, 2010, 31(1): 85-93.
[9] Chakherlou T N, Mirzajanzadeh M, Abazadeh B, et al. An investigation about interference fit effect on improving fatigue life of a holed single plate in joints. European Journal of Mechanics, 2010, 29(4): 675-682.
[10] Pradhan B, Ramesh B P. Assessment of beneficial effects of interference-fit in pin-loaded FRP composites. Journal of Reinforced Plastics and Composites, 2007, 26(8): 771-89.
[11] Pakdil M. Failure analysis of composite single bolted-joints subjected to bolt pretension. Indian Journal of Engineering & Materials Sciences, 2009, 16(2): 79-85.
[12] Li H X, Hu Y C, Zhang J Z. Study on simulating bolt pretension by using ANSYS. Journal of Shandong University of Science and Technology: Natural Science, 2006, 25(1): 57-59.(in Chinese) 李会勋, 胡迎春, 张建中. 利用ANSYS模拟螺栓预紧力的研究. 山东科技大学学报: 自然科学版, 2006, 25(1): 57-59.
[13] Oh J H, Kim Y G, Lee G D. Optimum bolted joints for hybrid composite materials. Composite Structures, 1997, 38(1-4): 329-341.
[14] Xiao Y, Ishikawa T. Bearing strength and failure behavior of bolted composite joints. Part I: experimental investigation. Composites Science and Technology, 2005, 65(7-8): 1022-1031.
[15] Sen F, Pakdil M, Sayman O, et al. Experimental failure analysis of mechanically fastened joints with clearance in composite laminates under preload. Materials & Design, 2008, 29(6): 1159-1169.
[16] Waszczak J P, Cruse T A. Failure mode and strength predictions of anisotropic bolt bearing specimens. Journal of Composite Materials, 1971, 5(3): 421-425.
[17] ASTM standard D5961/D5961M-10. Standard test method for bearing response of polymer-matrix composite laminates. West Conshohocken,PA: ASTM International, 2010.
[18] Geoffrey L K, John W F, John H S. Guide to design criteria for bolted and riveted joints. 2nd ed. Chicago: AISC, 1987: 111.
[19] Kelly G, Hallström S. Bearing strength of carbon fibre/epoxy laminates: effects of bolt-hole clearance. Composi-tes Part B, 2004, 35(4): 331-343.
[20] Adams D O, Bell S J. Compression strength reductions in composite laminates due to multiple-layer waviness. Composites Science and Technology, 1995, 53(2): 207-212.
[21] Caprino G, Giorleo G, Nele L, et al. Pin-bearing strength of glass mat reinforced plastics. Composites Part A, 2002, 33(6): 779-785.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

复合材料螺接性能的影响因素研究

Study on Factors Influencing the Performance of Composite Bolted Connections

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	龚煜廉, 张建国, 吴志刚, 褚光远, 范晓铎, 黄赢. 主动学习基自适应PC⁃Kriging模型的复合材料结构可靠度算法[J]. 航空学报, 2024, 45(8): 228982-228982.
[2]	贾文斌, 方磊, 张根, 史剑, 何泽侃, 宣海军. CNT树脂基复合材料断裂韧性的优化设计[J]. 航空学报, 2024, 45(7): 428971-428971.
[3]	张春云, 陈雄斌, 刘健, 崔苗. 酚醛树脂气凝胶复合材料热物性参数预测方法[J]. 航空学报, 2024, 45(6): 428848-428848.
[4]	黄领才. 纤维增强聚合物复合材料无损检测方法进展[J]. 航空学报, 2024, 45(5): 529697-529697.
[5]	高志廷, 马壮, 柳彦博. CVD-SiC阵列结构对ZrB₂/SiC涂层抗烧蚀性影响[J]. 航空学报, 2024, 45(3): 428842-428842.
[6]	张超, 曹勇, 赵振强, 张海洋, 孙建波, 王志华, 蔚夺魁. 树脂基复合材料在民用航空发动机中的应用与关键技术研究进展[J]. 航空学报, 2024, 45(2): 28556-028556.
[7]	马莹, 陈奡, 邓聪颖, 陈翔, 禄盛, 曾宪君. 纺织复合材料多尺度网格划分方法[J]. 航空学报, 2024, 45(10): 429180-429180.
[8]	杨倩, 王彦哲, 杨迪, 李泽众, 曲巍崴. 基于数据驱动的纤维增强复合材料自动铺放速度预测与规划[J]. 航空学报, 2024, 45(10): 429313-429313.
[9]	王四季, 张羽薇, 黄开明, 吕彪, 赵海凤, 王虎, 廖明夫. 基于改进粒子群算法的直升机动力涡轮转子系统优化方法[J]. 航空学报, 2024, 45(1): 228608-228608.
[10]	王宏越, 王兵, 方国东, 孟松鹤. 2.5D机织浅交弯联复合材料数字单元建模分析[J]. 航空学报, 2023, 44(9): 227478-227478.
[11]	牟浩蕾, 解江, 冯振宇, 程坤, 刘义. 大型运输类飞机典型机身框段坠撞特性分析[J]. 航空学报, 2023, 44(9): 227512-227512.
[12]	韩剑, 孙士勇, 牛斌, 杨睿, 吴东江. 树脂基复合材料点阵结构的制造技术研究进展[J]. 航空学报, 2023, 44(9): 628255-628255.
[13]	刘礼平, 齐雨阳, 蔺越国, 鲍蕊, 徐建新, 冯振宇, 卿光辉. 碳纤维复合材料胶铆混合修理结构静载拉伸失效[J]. 航空学报, 2023, 44(24): 428676-428676.
[14]	刘瑞峰, 孙晓哲, 李文辉, 王显, 闫杰. 高频脉冲电流改性SiC/Al复合材料微裂纹愈合机制及组织性能[J]. 航空学报, 2023, 44(22): 428598-428598.
[15]	杨钧超, 王雪明, 陈向明, 邹鹏, 王喆. 低速冲击损伤对复材加筋板压缩性能的影响[J]. 航空学报, 2023, 44(20): 228498-228498.