分腔流量比对涡轮曲端壁表面冷却特性实验

doi:10.7527/S1000-6893.2020.24399

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

分腔流量比对涡轮曲端壁表面冷却特性实验

杨寓全, 刘存良, 张杰, 黄蓉

西北工业大学动力与能源学院, 西安 710072

收稿日期:2020-06-10 修回日期:2020-07-10 发布日期:2020-09-17
通讯作者: 刘存良 E-mail:liucunliang@nwpu.edu.cn
基金资助:
国家自然科学基金（51936008）；西北工业大学硕士研究生创意创新种子基金（CX2020136）

Effect of mass flow ratios on film cooling characteristics of endwall: Experimental study

YANG Yuquan, LIU Cunliang, ZHANG Jie, HUANG Rong

School of Power and Energy, Northwestern Polytechnical University, Xi'an 710072, China

Received:2020-06-10 Revised:2020-07-10 Published:2020-09-17
Supported by:
National Natural Science Foundation of China (51936008); the Seed Foundation of Innovation and Creation for Graduate Students in Northwestern Polytechnical University(CX2020136)

摘要/Abstract

摘要： 利用高速风洞及压敏漆（PSP）技术，研究了端壁表面不同分腔流量比对端壁表面的气膜冷却效率的影响。对比各个分腔在不同流量比下端壁表面的气膜冷却效率的详细分布发现：端壁表面的气膜冷却效率随着槽缝流（分腔1）流量比的增加而增大，随着槽缝喷射冷气流量的增加，冷气在端壁表面的覆盖范围变广，同时冷却效果也有所提升；随着端壁前部分腔（分腔2）冷气流量比的增加，叶栅通道喉部上游区域的冷却流体会出现明显的吹离壁面的情况，端壁表面的气膜冷却效率也会随之减小；端壁后部分腔（分腔3）冷气流量比对端壁表面的冷却效率的影响与分腔2类似。

关键词: 气膜冷却, 端壁, 流量比, 冷却效率, 压敏漆技术

Abstract: The effect of mass flow ratios different on the film cooling effectiveness of the enwall is studied using the Pressure-Sensitive Paint (PSP) technology and high-speed wind tunnel. The detailed distribution of the film cooling effectiveness on the endwall surface under different flow ratios of each cavity is obtained. The film cooling effectiveness on the endwall surface increases with the increase of the slot mass flow ratio. As the coolant injected into the slot increases, the coverage of the coolant on endwall surface becomes, cooling performance. As the coolant mass flow ratio of 2 increases, because the coolant from cooling holes liftoff from the wall surface to the excessively high speed. The influence of the mass flow ratio cavity 3 on the cooling effectiveness of the endwall is similar to that of cavity 2.

Key words: film cooling, endwall, mass flow ratio, cooling effectiveness, pressure-sensitive paint technology

中图分类号:

V231.1

杨寓全, 刘存良, 张杰, 黄蓉. 分腔流量比对涡轮曲端壁表面冷却特性实验[J]. 航空学报, 2021, 42(7): 124399-124399.

YANG Yuquan, LIU Cunliang, ZHANG Jie, HUANG Rong. Effect of mass flow ratios on film cooling characteristics of endwall: Experimental study[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(7): 124399-124399.

参考文献

[1] BARIGOZZI G, BENZONI G, FRANCHINI G, et al. Fan-shaped hole effects on the aero-thermal performance of a film-cooled endwall[J]. Journal of Turbomachinery, 2006, 128(1):507-518.
[2] 刘存良, 朱惠人, 白江涛, 等. 基于瞬态液晶测量技术的收缩-扩张形孔气膜冷却特性[J]. 航空学报, 2009, 30(5):812-818. LIU C L, ZHU H R, BAI J T, et al. Film cooling characteristics of converging-expanding hole with transient liquid crystal measurement technique[J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(5):812-818(in Chinese).
[3] RAVI B V, DESHPANDE S, RAMESH S, et al. Film cooling performance of tripod holes on the endwall upstream of a first stage nozzle guide vane[C]//ASME International Mechanical Engineering Congress & Exposition. New York:ASME,2015.
[4] 叶林,刘存良,杨寓全,等.V肋对尾缘劈缝气膜冷却特性影响的实验研究[J].航空学报, 2021, 42(4):124181. YE L, LIU C L, YANG Y Q, et al. Experimental study of the effect of v-shaped ribs on the film cooling characteristics for the trailing-edge cutback[J]. Acta Aeronautica et Astronautica Sinica, 2021, 42(4):124181(in Chinese).
[5] KOHLI A, BOGARD D G. Effects of very high free-stream turbulence on the jet-mainstream interaction in a film cooling flow[J]. Journal of Turbomachinery, 1998, 120(4):785-790.
[6] CHEN A F,SHIAU C C, HAN J C.Turbine blade platform film cooling with fan-shaped holes under simulated swirl purge flow and slashface leakage conditions:GT-2017-63119[R].New York:ASME, 2017.
[7] THRIFT A A, THOLE K A, HADA S. Effects of an axisymmetric contoured endwall on a nozzle guide vane:Adiabatic effectiveness measurements[J]. Journal of Turbomachinery, 2011,133(4):1617-1627.
[8] ZHANG L, YIN J, LIU K, et al. Effect of hole diameter on nozzle endwall film cooling and associated phantom cooling[C]//ASME Turbo Expo 2015:Turbine Technical Conference and Exposition. New York:ASME,2015.
[9] 张扬, 齐士博, 袁新. 涡轮流场影响端壁气膜冷却的实验研究[J]. 工程热物理学报, 2011, 32(6):941-944. ZHANG Y, QI S B, YUAN X.Experimental investigation on the turbine blade platform film cooling effected by the flow field[J]. Journal of Engineering Thermophysics, 2011, 32(6):941-944(in Chinese).
[10] SHIAU C C, CHEN A F, HAN J C, et al. Full-scale turbine vane endwall film-cooling effectiveness distribution using pressure-sensitive paint technique[J]. Journal of Turbomachinery,2016,138(5):051002.
[11] CHOWDHURY N H, SHIAU C C, HAN J C, et al. Film cooling effectiveness comparison on turbine vane endwall with cluster configurations using psp measurement technique[C]//ASME 2017 International Mechanical Engineering Congress and Exposition.New York:ASME,2017.
[12] LI M, LI X, REN J, et al. Overall cooling effectiveness characteristic and influence mechanism on an endwall with film cooling and impingement[C]//ASME Turbo Expo 2015:Turbine Technical Conference and Exposition. New York:ASME, 2015.
[13] ZHANG L J, JAISWAL R S. Turbine nozzle endwall film cooling study using pressure-sensitive paint[J]. Journal of Turbomachinery,2001,123(4):730-738.
[14] EL-GABRY L, XU H, LIU K, et al. Effect of coolant injection angle on nozzle endwall film cooling:Experimental and numerical analysis in linear cascade[C]//ASME Turbo Expo 2018:Turbomachinery Technical Conference and Exposition. New York:ASME, 2018.
[15] CHOWDHURY N H, SHIAU C C, HAN J C, et al. Turbine vane endwall film cooling with slashface leakage and discrete hole configuration[J]. Journal of Turbomachinery, 2017,139(6):1-13.
[16] CHOWDHURY N H, SHIAU C C, HAN J C, et al. Turbine vane endwall film cooling study from axial-row configuration with simulated upstream leakage flow[C]//ASME Turbo Expo 2017:Turbomachinery Technical Conference and Exposition. New York:ASME, 2017.
[17] ORNANO F, POVEY T. Experimental and computational study of the effect of momentum-flux ratio on high pressure ngv endwall cooling systems[C]//ASME Turbo Expo 2017:Turbomachinery Technical Conference and Exposition. New York:ASME, 2017.
[18] KLINE S J, MCCLINTOCK F A. Describing uncertainties in single-sample experiments[J].Journal of Mechanical Engineering, 1953, 75:3-8.
[19] WRIGHT L M, MCCLAIN S T, CLEMENSON M D. Effect of density ratio on flat plate film cooling with shaped holes using PSP[C]//ASME Turbo Expo 2010:Power for Land, Sea, and Air. New York:ASME, 2010.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

分腔流量比对涡轮曲端壁表面冷却特性实验

Effect of mass flow ratios on film cooling characteristics of endwall: Experimental study

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王博, 吴艳辉, 黄令举, 王子胥. 基于端壁L形凹槽的扩压叶栅角区分离控制[J]. 航空学报, 2024, 45(10): 129206-129206.
[2]	任明, 刘存良, 杜昆, 张丽, 朱惠人, 张博伦. 弯扭涡轮叶片前缘复合角孔气膜冷却[J]. 航空学报, 2023, 44(18): 128315-128315.
[3]	王斌, 王海涛, 王玉峰, 张文武. 热障涂层水助激光扫描加工试验[J]. 航空学报, 2022, 43(4): 525353-525353.
[4]	叶林, 刘存良, 朱安冬, 周天亮. 紧凑凸肋通道对尾缘劈缝气膜冷却特性的影响[J]. 航空学报, 2022, 43(3): 125174-125174.
[5]	夏凯龙, 何箐, 张雨生. 基于红外热成像的涡轮叶片气膜孔孔径测量方法及缩孔规律[J]. 航空学报, 2022, 43(12): 426271-426271.
[6]	罗世彬, 庙智超, 宋佳文. 高超声速飞行器前缘主动冷却影响因素[J]. 航空学报, 2022, 43(12): 627023-627023.
[7]	王进, 孙杰, 赵占明, 张勃, 任晓栋, 谢公南. 基于结构参数分析的姊妹孔气膜冷却性能研究[J]. 航空学报, 2021, 42(7): 124775-124775.
[8]	叶林, 刘存良, 杨寓全, 黄蓉, 朱安冬. V肋对尾缘劈缝气膜冷却特性的影响[J]. 航空学报, 2021, 42(6): 124181-124181.
[9]	李左飙, 温风波, 唐晓雷, 苏良俊, 王松涛. 基于深度学习的单排孔气膜冷却性能预测[J]. 航空学报, 2021, 42(4): 524331-524331.
[10]	陈大为, 朱惠人, 李华太, 刘海涌, 周道恩. 尾迹对涡轮动叶全表面气膜冷却效率的影响[J]. 航空学报, 2019, 40(3): 122651-122651.
[11]	祝培源, 宋立明, 李军, 丰镇平. 间隙位置和几何对端壁冷却性能的影响[J]. 航空学报, 2017, 38(9): 520942-520942.
[12]	周君辉, 张靖周. 气膜孔局部堵塞对叶片压力面冲击-扰流柱-气膜结构综合冷却效率的影响[J]. 航空学报, 2016, 37(9): 2729-2738.
[13]	史磊, 刘波, 巫骁雄, 那振喆, 张鹏. 对转压气机轮缘端壁抽吸流场特性数值分析及实验研究[J]. 航空学报, 2015, 36(9): 2968-2980.
[14]	张靖周, 王旭, 单勇. 塞锥后体气膜冷却对轴对称塞式喷管红外辐射和气动性能的影响[J]. 航空学报, 2015, 36(8): 2601-2608.
[15]	张晓兵, 孙瑞峰. 二次法激光加工小孔技术[J]. 航空学报, 2014, 35(3): 894-901.