辐射涂层对空心涡轮叶片定向凝固组织的影响

doi:10.7527/S1000-6893.2017.421462

材料工程与机械制造

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

辐射涂层对空心涡轮叶片定向凝固组织的影响

黄福享, 苗恺, 鲁中良, 徐文梁, 朱伟军, 李涤尘

西安交通大学机械制造系统工程国家重点实验室, 西安 710049

收稿日期:2017-05-27 修回日期:2017-08-31 出版日期:2018-03-15 发布日期:2017-08-31
通讯作者: 鲁中良,E-mail:zllu@mail.xjtu.edu.cn E-mail:zllu@mail.xjtu.edu.cn
基金资助:
国家"973"计划（2013CB035703）；中央高校基本科研业务费国家重点研发计划培育项目

Effects of radiation coatings on directional solidification microstructure of hollow turbine blades

HUANG Fuxiang, MIAO Kai, LU Zhongliang, XU Wenliang, ZHU Weijun, LI Dichen

State Key Laboratory for Manufacturing Systems Engineering, Xi'an Jiaotong University, Xi'an 710049, China

Received:2017-05-27 Revised:2017-08-31 Online:2018-03-15 Published:2017-08-31
Supported by:
National Basic Research Program of China (2013CB035703);the Fundamental Research Founds for the Central Universities

摘要/Abstract

摘要： 为了得到组织细密的定向晶叶片，采用数值模拟和实验相结合的方法，对比研究了铸型表面涂挂具有较高辐射性能的石墨涂层和氧化铬涂层对空心涡轮叶片定向凝固组织的影响。理论分析表明，铸型表面辐射系数提高能够在一定程度上提高铸件顶端的温度梯度。实验结果表明，通过在铸型表面涂挂氧化铬涂层材料，显著提高了铸型表面辐射散热性能，降低了铸件顶端的一次枝晶间距。铸件顶端的一次枝晶平均间距为336 μm，较未涂挂任何涂层减小12.5%，较涂挂石墨涂层减小2.9%，定向晶组织得到显著细化。采用铸型外表面涂挂氧化铬辐射涂层的方法成形的复杂结构空心涡轮叶片定向晶组织形态良好。

关键词: 空心涡轮叶片, 定向凝固, 辐射涂层, 定向晶, 整体式陶瓷铸型

Abstract: To obtain a turbine blade with refined directional crystals, the effects of the graphite coating and the chromium oxide coating on the directional solidification microstructure are studied by numerical simulations and experiments. Numerical simulation results show that the temperature gradient at the top castings is improved by increasing the emissivity of the mold surface. The experimental results show that after the mold surface is coated with the chromium oxide, the heat dissipation performance of the mold surface is remarkably improved, and the primary dendrite spacing at the top of the casting is reduced. The average primary dendrite spacing at the top of the casting is 336 μm, 12.5% less than the one without coating and 2.9% lower than the one coated with graphite, and the directional solidification microstructure is significantly refined. A turbine blade with refined directional crystal is formed by using the integral ceramic mold with the chromium oxide coating.

Key words: hollow turbine blades, directional solidification, radiation coating, directional crystal, integral ceramic mold

中图分类号:

黄福享, 苗恺, 鲁中良, 徐文梁, 朱伟军, 李涤尘. 辐射涂层对空心涡轮叶片定向凝固组织的影响[J]. 航空学报, 2018, 39(3): 421462-421462.

HUANG Fuxiang, MIAO Kai, LU Zhongliang, XU Wenliang, ZHU Weijun, LI Dichen. Effects of radiation coatings on directional solidification microstructure of hollow turbine blades[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(3): 421462-421462.

参考文献

[1] REED R C. The superalloys:Fundamentals and applications[M]. Cambridge:Cambridge University Press, 2008:107-150.
[2] 冯炜, 汪文虎, 王孝忠, 等. 空心涡轮叶片精铸蜡型陶芯定位元件尺寸计算方法[J]. 航空学报, 2013, 34(1):181-186. FENG W, WANG W H, WANG X Z, et al. Size calculation method of ceramic core locators for hollow turbine blade investment casting wax patterns[J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(1):181-186(in Chinese).
[3] 崔康, 汪文虎, 蒋睿嵩, 等. 涡轮叶片精铸模具陶芯定位元件逆向调整算法[J]. 航空学报, 2011, 32(10):1924-1929. CUI K, WANG W H, JIANG R S, et al. Reverse adjustment algorithm of ceramic core locators in hollow turbine blade investment casting die[J]. Acta Aeronautica et Astronautica Sinica, 2011, 32(10):1924-1929(in Chinese).
[4] 张立同, 曹腊梅, 刘国利. 近净形熔模精密铸造理论与实践[M]. 北京:国防工业出版社, 2007:207-220. ZHANG L T, CAO L M, LIU G L. Near net shape casting theory and practice[M]. Beijing:National Defence Industry Press, 2007:207-220(in Chinese).
[5] 丁阳, 常海萍. 涡轮叶片冷却有效性分析[J]. 航空学报, 2013, 34(1):46-51. DING Y, CHANG H P. Analysis of turbine blade cooling effectiveness[J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(1):46-51(in Chinese).
[6] 马德新. 高温合金叶片单晶凝固技术的新发展[J]. 金属学报, 2015, 51(10):1179-1190. MA D X. Development of single crystal solidification technology for production of superalloy turbine blades[J]. Acta Metallurgica Sinica, 2015, 51(10):1179-1190(in Chinese).
[7] 陈荣章. 航空铸造涡轮叶片合金和工艺发展的回顾与展望[J]. 航空制造技术, 2002(2):19-23. CHEN R Z. Review and prospect of developments of cast superalloys and technology of aeroengine turbine blade[J]. Aeronautical Manufacturing Technology, 2002(2):19-23(in Chinese).
[8] 喻秋平, 周尧和. 铸件定向凝固过程的数值模拟[J]. 航空学报, 1984, 5(3):313-320. YU Q P, ZHOU Y H. Numerical simulation of directional solidification process of castings[J]. Acta Aeronautica et Astronautica Sinica, 1984, 5(3):313-320(in Chinese).
[9] LIAN Y, LI D, ZHANG K. A method for flattening the solidification front in directional solidification technology[J]. Journal of Crystal Growth, 2015, 426(1):186-197.
[10] LIAN Y, LI D, ZHANG K. Effects of the location of a cast in the furnace on flatness of the solidification front in directional solidification[J]. Journal of Crystal Growth, 2016, 451:33-41.
[11] SZELIGA D, KUBIAK K, JARCZYK G. The influence of the radiation baffle on predicted temperature gradient in single crystal CMSX-4 castings[J]. International Journal of Metalcasting, 2013, 7(3):17-23.
[12] 乐献刚, 彭志江, 邹建波, 等. 隔热挡板厚度对DD6单晶高温合金凝固组织的影响[J]. 特种铸造及有色合金, 2014, 34(3):309-313. YUE X G, PENG Z J, ZOU J B, et al. Effects of thermal baffle thickness on the solidification microstructure of single crystal superalloy DD6[J]. Special Casting & Nonferrous Alloys, 2014, 34(3):309-313(in Chinese).
[13] QIN L, SHEN J, YANG G, et al. A design of non-uniform thickness mould for controlling temperature gradient and S/L interface shape in directionally solidified superalloy blade[J]. Materials & Design, 2017, 116:565-576.
[14] MA D X, BVHRIG-POLACZEK A. Avoiding grain defects in single crystal components by application of a heat conductor technique[J]. International Journal of Materials Research, 2009, 100(8):1145-1151.
[15] BETZ U, HUGO F, MAYER H. Improvements in DS/SC precision casting[C]//3rd International Charles Parsons Turbine Conference:Materials Engineering in Turbines and Compressors. London:Institute of Materials, 1995:557-565.
[16] 陈荣章, 佘力, 张宏炜, 等. DZ125定向凝固高温合金的研究[J]. 航空材料学报, 2000, 20(4):14-19. CHEN R Z, SHE L, ZHANG H W, et al. Investigation of directionally solidified alloy DZ125[J]. Journal of Aeronautical Materials, 2000, 20(4):14-19(in Chinese).
[17] 李涤尘, 吴海华, 卢秉恒. 快速原型制造技术/型芯型壳一体化空心涡轮叶片制造方法[J]. 航空制造技术, 2009(3):36-42. LI D C, WU H H, LU B H. Shaping method of hollow turbine blades with intergral shell and core ceramic mold[J]. Aeronautical Manufacturing Technology, 2009(3):36-42(in Chinese).
[18] 刘涛, 鲁中良, 苗恺, 等. 面向空心涡轮叶片的氧化铝基陶瓷铸型高温强化制造[J]. 航空学报, 2014, 35(7):2072-2080. LIU T, LU Z L, MIAO K, et al. High-temperature strengthening manufacturing of alumina-based ceramic molds used for hollow turbine blades[J]. Acta Aeronautica et Astronautica Sinica, 2014, 35(7):2072-2080(in Chinese).
[19] 李涤尘, 苏秦, 卢秉恒. 快速制造技术-增材制造-创新与创业的利器[J]. 航空制造技术, 2015(10):38-43. LI D C, SU Q, LU B H. Additive manufacturing-tool for innovation and entrepreneurship[J]. Aeronautical Manufacturing Technology, 2015(10):38-43(in Chinese).
[20] 圆山重直. 传热学[M]. 王世学, 张信荣, 译. 北京:北京大学出版社, 2011:110-117. MARUYAMA S. Heat transfer[M]. WANG S X, ZHANG X R, translated. Beijing:Peking University Press, 2011:110-117(in Chinese).
[21] MA D, SAHM P R. Primary spacing in directional solidification[J]. Metallurgical and Materials Transactions A:Physical Metallurgy and Material, 1998, 29(13):1113-1119.
[22] LU S Z, HUNT J D. A numerical analysis of dendritic and cellular array growth:The spacing adjustment mechanisms[J]. Journal of Crystal Growth, 1992, 123(1-2):17-34.
[23] HUNT J D, LU S Z. Numerical modeling of cellular/dendritic array growth:spacing and structure predictions[J]. Metallurgical and Materials Transactions A:Physical Metallurgy and Material, 1996, 27(3):611-623.
[24] WHITESELL H S, LI L, OVERFELT R A. Influence of solidification variables on the dendrite arm spacings of Ni-based superalloys[J]. Metallurgical and Materials Transactions B:Process Metallurgy and Materials Processing Science, 2000, 31(3):546-551.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

辐射涂层对空心涡轮叶片定向凝固组织的影响

Effects of radiation coatings on directional solidification microstructure of hollow turbine blades

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	崔康, 汪文虎, 蒋睿嵩, 赵德中, 靳淇超. 基于力约束的空心涡轮叶片陶芯定位方法[J]. 航空学报, 2017, 38(9): 421209-421209.
[2]	刘涛, 鲁中良, 苗恺, 李涤尘. 面向空心涡轮叶片的氧化铝基陶瓷铸型高温强化制造[J]. 航空学报, 2014, 35(7): 2072-2080.
[3]	张虎, 原赛男, 周春根, 沙江波, 赵新青, 贾丽娜. Nb-Si金属间化合物基超高温合金研究进展[J]. 航空学报, 2014, 35(10): 2756-2766.
[4]	杨晓光, 黄佳, 王井科, 胡晓安, 石多奇. 定向凝固镍基高温合金缺口低循环疲劳性能及寿命预测[J]. 航空学报, 2013, 34(7): 1596-1604.
[5]	冯炜, 汪文虎, 王孝忠, 骆金虎. 空心涡轮叶片精铸蜡型陶芯定位元件尺寸计算方法[J]. 航空学报, 2013, 34(1): 181-186.
[6]	顾玉丽, 滕旭东, 刘昌奎, 何玉怀, 陶春虎. DZ125定向凝固高温合金长期时效后的显微组织和超高周疲劳行为[J]. 航空学报, 2012, 33(11): 2136-2142.
[7]	潘情, 郑立静, 桑于蓉, 周磊, 李岩, 张虎. 定向凝固Ni-44Ti-5Al-2Nb-1Mo合金的组织特征[J]. 航空学报, 2011, 32(7): 1345-1350.
[8]	卜昆, 王虹, 周桐, 李世峰, 沈翔鸿. 精铸空心涡轮叶片模具虚拟修模方法[J]. 航空学报, 2011, 32(3): 538-545.
[9]	孙瑞杰;闫晓军;聂景旭. 定向凝固涡轮叶片高温低周疲劳的破坏特点[J]. 航空学报, 2011, 32(2): 337-343.
[10]	徐岳琳;卜昆;张定华;黄胜利;程云勇;索瑞. 内切圆弦长法计算空心涡轮叶片蜡模壁厚[J]. 航空学报, 2011, 32(2): 344-350.
[11]	崔康, 汪文虎, 蒋瑞嵩, 赵德高. 涡轮叶片精铸模具陶芯定位元件逆向调整算法[J]. 航空学报, 2011, 32(10): 1924-1929.
[12]	闫晓军, 邓瑛, 孙瑞杰, 谢建文. 定向凝固涡轮叶片不同部位材料疲劳性能差异研究[J]. 航空学报, 2011, 32(10): 1930-1936.
[13]	张卫方;李运菊;高威;姜涛;陶春虎. 定向凝固DZ4合金的低周疲劳行为与稳定循环应力[J]. 航空学报, 2004, 25(4): 357-361.
[14]	张卫方;高威;赵爱国;陶春虎;田继丰;姚戈. 定向凝固合金叶片的再结晶与疲劳失效[J]. 航空学报, 2003, 24(4): 377-381.
[15]	彭德林;安阁英. 定向凝固时热溶质对流对Al/AlLi共晶生长形态稳定性的影响[J]. 航空学报, 2001, 22(4): 382-384.