基于缺陷敏感度的加筋短板承载能力

doi:10.7527/S1000-6893.2020.23832

固体力学与飞行器总体设计

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

基于缺陷敏感度的加筋短板承载能力

刘存¹, 赵冬强^1,2

1. 航空工业第一飞机设计研究院强度设计研究所, 西安 710089;
2. 西北工业大学航空学院, 西安 710072

收稿日期:2020-01-13 修回日期:2020-04-13 发布日期:2020-04-10
通讯作者: 刘存 E-mail:liuc@nuaa.edu.cn
基金资助:
航空科学基金（2015ZB52015）

Load-carrying capacity of stiffened short plates based on imperfection sensitivity

LIU Cun¹, ZHAO Dongqiang^1,2

1. Department of Strength Design, AVIC The First Aircraft Institute, Xi'an 710089, China;
2. School of Aeronautics, Northwestern Polytechnical University, Xi'an 710072, China

Received:2020-01-13 Revised:2020-04-13 Published:2020-04-10
Supported by:
Aeronautical Science Foundation of China (2015ZB52015)

摘要/Abstract

摘要： 加筋短板以其高比强度成为飞机结构的基本元素，其设计方法是基于传统的Euler柱屈曲理论和Timoshenko板壳弹性稳定性理论，由于进行了假设和简化，不能很好地预测破坏载荷。采用GMNIA（Geometrically and Material Nonlinear Analysis with Imperfections）分析方法对加筋短板的承载能力进行仿真分析，结果与试验数据吻合良好。基于GMNIA方法开展了不同类型的几何缺陷对加筋短板承载能力敏感度分析，研究了初弯曲、初偏心以及初变形对加筋短板承载能力的影响。给出了表征加筋短板初弯曲和初变形缺陷的计算公式，为有限元模拟加筋短板破坏过程及预测承载能力提供了技术支持。此外，给出了初弯曲下加筋短板承载能力的设计许用值，提出了通过控制加工制造公差量来提高结构极限承载能力的设计建议，具有明确的工程应用意义和实用价值。

关键词: 加筋短板, 初始几何缺陷, 敏感度, 承载能力, 设计建议

Abstract: Stiffened short plates are the basic components of aircraft structure because of their high specific strength. Their design method is based on the traditional Euler column buckling theory and Timoshenko plate shell elastic stability theory. However, the failure load cannot be well predicated due to the assumption and simplification in the design. The load-carrying capacity of the stiffened short plate is simulated by the method of GMNIA (Geometric and Material Nonlinear Analysis with Imperfections), and the results are in good agreement with the experimental data. Based on GMNIA, the sensitivity analysis of different types of geometric imperfections in the load-carrying capacity of the stiffened short plate is carried out. The influence of initial bending, initial eccentricity and initial deformation on the load-carrying capacity of the stiffened short plate is studied. The calculation formulas of the initial bending and initial deformation imperfections of the stiffened short plate are given, providing technical support for the finite element simulation of the failure process and prediction of the load-carrying capacity of the stiffened short plate. Furthermore, the allowable design values of the bearing capacity of stiffened short plates under initial bending imperfection are presented, and suggestions of improving the ultimate bearing capacity in the design by controlling the manufacturing tolerance are put forward, exhibiting engineering application significance and practical value.

Key words: stiffened short plate, initial geometrical imperfections, sensitivity, load bearing capacity, design suggestion

中图分类号:

V224

刘存, 赵冬强. 基于缺陷敏感度的加筋短板承载能力[J]. 航空学报, 2020, 41(10): 223832-223832.

LIU Cun, ZHAO Dongqiang. Load-carrying capacity of stiffened short plates based on imperfection sensitivity[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(10): 223832-223832.

参考文献

[1] CALLADINE C R. Understanding imperfection-sensitivity in the buckling of thin-walled shells[J].Thin-Walled Structures, 1995, 23(1):215-235.
[2] 郝鹏,王博,李刚,等. 基于缺陷敏感性分析的加筋圆柱壳结构设计[J].应用力学学报, 2013, 30(3):344-349. HAO P, WANG B, LI G, et al. Structural design of stiffened shells based on imperfection sensitivity analysis[J].Chinese Journal of Applied Mechanics, 2013, 30(3):344-349(in Chinese).
[3] CAMPBELL J,HETEY L,VIGNJEVIC R. Nonlinear idealization error analysis of a metallic stiffened panel loaded in compression[J].Thin-Walled Structures, 2012, 54:44-53.
[4] BERNARD E S,COLEMAN R,BRIDGE R Q. Measurement and assessment of geometrical imperfections in thin-walled panels[J].Thin-Walled Structures, 1999, 33:103-126.
[5] LANZI L A. A numerical and experimental investigation on composite stiffened panels into post-buckling[J].Thin-Walled Structures, 2004, 42(12):1645-1664.
[6] HOUSTON G, QUINN D, MYRPHY A, et al. Impact of geometric imperfections on metallic stiffened panels with skin bay buckling containment features[C]//53th AIAA/ASME/ASCE/AHS/ASC Structure, Structure Dynamics, and Materials Conference. Reston:AIAA, 2012.
[7] PAULO R M F, TEIXEIRA-DIAS F, VALENTE R A F. Numerical simulation of aluminum stiffened panels subjected axial compression:Sensitivity analyses to initial geometrical imperfections and material properties[J].Thin-Walled Structures, 2013, 62(1):65-74.
[8] XU M C, SOARES C G. Assessment of the ultimate strength of narrow stiffened panel tests specimens[J].Thin-Walled Structures, 2012, 55:11-21.
[9] 刘存,张磊,杨卫平. 舰载机壁板剪切后屈曲承载能力预测与试验验证[J].航空学报, 2019, 40(4):622300. LIU C, ZAHNG L, YANG W P. Post-buckling study and test verification of carrier-based aircraft wing stiffened panels under shear load[J].Acta Aeronautica et Astronautica Sinica, 2019, 40(4):622300(in Chinese).
[10] HILBURGER M W, NEMETH M P, STARNES J H. Shell buckling design criteria based on manufacturing imperfection signatures[J].AIAA Journal, 2006, 44(3):654-663.
[11] HILBURGER M W, STARNES J H J. Effects of imperfections on the buckling response of compression-loaded composite shells[C]//41 st AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference. Reston:AIAA, 2000.
[12] RIGO P, SARGHIUTA R, ESTEFEN S, et al. Sensitivity analysis on ultimate strength of aluminum stiffened panels[J].Marine Structures, 2003,16:437-468.
[13] COUTO C, VILA R P. Numerical investigation on the influence of imperfections in the local buckling of thin-walled I-shaped sections[J].Thin-Walled Structures, 2019, 135:89-108.
[14] SALTELLI A, RATTO M, TARANTOLA S, et al. Sensitivity analysis practices:Strategies for model-based inference[J].Reliability Engineering and System Safety, 2006, 91(10-11):1109-1125.
[15] 罗鹏程,傅攀峰. 武器装备敏感性分析方法综述[J].计算机工程与设计, 2008, 29(21):5546-5549. LUO P C, FU P F. Review on weapons and equipment sensitivity analysis methods[J].Computer Engineering and Design, 2008, 29(21):5546-5549(in Chinese).
[16] SALTELLI A, MARIVOET J. Non-parametric statistics in sensitivity analysis for model output:A comparison of selected techniques[J].Reliability Engineering System Safety, 1990, 28(2):229-253.
[17] HELTON J C, DAVIS F J. Survey of sampling-based methods for uncertainty and sensitivity analysis[J].Reliability Engineering System Safety, 2006, 91(10):1175-1209.
[18] SOBOI I M. Global sensitivity indices for nonlinear mathematical models and their Monte Carlo estimates[J].Mathematics and Computers in Simulation, 2001, 55(1-3):271-280.
[19] BORGONOVO E. A new uncertainty importance measure[J].Reliability Engineering System Safety, 2007, 92(6):771-784.
[20] CUI L J, LU Z Z, ZHAO X P. Moment-independent importance measure of basic random variable and its probability density evolution solution[J].Science China Technological Sciences, 2010, 53(4):1138-1145.
[21] LI L Y, LU Z Z, FENG J, et al. Moment-independent importance measure of basic variable and its state dependent parameter solution[J].Structural Safety, 2012, 38:40-47.
[22] RICE R C, JACKSON J L, BAKUCKAS J, et al. Metallic materials properties development and standardization[M]. Washington,D. C.:Federal Aviation Administration, 2003:3-429.
[23] LANZI L A, GIAVOTTO V O. Post-buckling optimization of composite stiffened panels computations and experiments[J].Composite Structures, 2006,73:208-220.
[24] ABRAMOVICH H, BISAGNI C, CORDISCO P. Post-buckling test simulation of a stiffened composite panel[C]//48th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference. Reston:AIAA, 2007.
[25] ZHANG S M, KHAN I. Buckling and ultimate capability of plates and stiffened panels in axial compression[J].Marine Structures, 2009, 22(4):791-808.
[26] XU M C, SOARES C G. Assessment of the ultimate strength of narrow stiffened panel tests specimens[J].Thin-Walled Structures, 2012, 55:11-21.
[27] LI Y B, PAN Q, HUANG M H, et al. Set-based parametric modeling, buckling and ultimate strength estimation of stiffened ship structures[J].Journal of Central South University, 2019, 26(7):1958-1975.
[28] MAZZOLAN M. Aluminum alloy structures[M]. Boston:Pitman, 1985.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

基于缺陷敏感度的加筋短板承载能力

Load-carrying capacity of stiffened short plates based on imperfection sensitivity

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 14

编辑推荐

Metrics

本文评价

[1]	王志祥, 雷勇军, 段静波, 欧阳兴, 张大鹏, 王婕. 重型运载火箭集中力扩散舱段多区域联合设计与优化[J]. 航空学报, 2022, 43(3): 225135-225135.
[2]	高伟, 刘存, 陈顺强. 变厚度复合材料加筋板轴压试验及分析方法[J]. 航空学报, 2022, 43(11): 526764-526764.
[3]	刘存, 张磊, 杨卫平. 舰载机壁板剪切后屈曲承载能力预测与试验验证[J]. 航空学报, 2019, 40(4): 622300-622300.
[4]	倪杨, 徐元铭. 金属次加筋结构的单轴压载稳定性优化[J]. 航空学报, 2015, 36(5): 1511-1519.
[5]	李波, 杨毅. 星载平面可展天线支撑桁架的结构效率优化[J]. 航空学报, 2015, 36(12): 3853-3860.
[6]	宋言明, 杨洋. 非晶态薄带冷却铜辊用内反馈静压轴承数值模拟[J]. 航空学报, 2014, 35(4): 1157-1164.
[7]	王秋晓, 孔波, 汪飞, 姜怀芳. 用于质量特性参数测量的新型气浮扭摆台[J]. 航空学报, 2014, 35(3): 885-893.
[8]	白江波, 熊峻江, 高军鹏, 益小苏, 张子龙, 何先成, 刘志真, 李雪芹. 可折叠复合材料豆荚杆的制备与验证[J]. 航空学报, 2011, 32(7): 1217-1223.
[9]	曾励;汪通悦;徐龙祥;刘正埙. 永磁电磁轴承产生悬浮力的机理研究[J]. 航空学报, 2000, 21(3): 219-221.
[10]	谢鸣九;朱立平;施丽中. 铺层顺序对复合材料层合结构承载的影响[J]. 航空学报, 1991, 12(12): 560-564.
[11]	关长文;陈浩然. 复合材料层合板、壳结构的承载能力[J]. 航空学报, 1987, 8(5): 237-243.
[12]	王谓季;张阿舟. 振动特性敏感区上的结构故障诊断与监测[J]. 航空学报, 1987, 8(3): 138-144.
[13]	黄敬贤;黄雅章;刘夏石. 飞机结构的损坏过程承载能力、破坏部位有限元分析[J]. 航空学报, 1987, 8(2): 39-46.
[14]	傅仙罗. 动压气浮球轴承承载力分析[J]. 航空学报, 1984, 5(3): 346-351.