首页 >

Al含量对空心阴极等离子烧结Ti/Ni等原子比TiNiAl合金组织和力学性能的影响

刘伯路, 刘子利, 刘希琴, 王怀涛, 王文静   

  1. 南京航空航天大学 材料科学与技术学院, 江苏 南京 210016
  • 收稿日期:2012-03-29 修回日期:2012-05-03 出版日期:2013-03-25 发布日期:2013-03-29
  • 通讯作者: 刘子利,Tel.: 025-52112626 E-mail: liuzili@nuaa.edu.cn E-mail:liuzili@nuaa.edu.cn
  • 作者简介:刘伯路 男, 硕士研究生。主要研究方向: 钛合金粉末冶金技术。 Tel: 025-52112626 E-mail: blliu2011@hotmail.com;刘子利 男, 博士, 教授。主要研究方向: 轻合金精密成形技术。 Tel: 025-52112626 E-mail: liuzili@nuaa.edu.cn
  • 基金资助:

    常熟市科技发展计划项目(CC200913)

Effect of Al Content on Microstructure and Mechanical Properties of Hollow Cathode Plasma Sintering TiNiAl Alloys with Equal Ti/Ni Atom Ratio

LIU Bolu, LIU Zili, LIU Xiqin, WANG Huaitao, WANG Wenjing   

  1. College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
  • Received:2012-03-29 Revised:2012-05-03 Online:2013-03-25 Published:2013-03-29
  • Supported by:

    Changshu Science and Technology Development Planning Project (CC200913)

摘要:

采用空心阴极等离子烧结工艺制备了Ti/Ni等原子比的Ti50-x/2Ni50-x/2Alx(x=0,3,6,9)合金,研究了Al含量对合金微观组织以及力学性能的影响。结果表明:未添加铝的合金微观组织主要由NiTi基体、强化相Ti2Ni、Ni3Ti及孔隙组成;随着Al含量的提高,合金中Ti2Ni(Al)数量不断增多,孔隙数量和孔径不断增加,Ni3Ti(Al)数量不断减少,在Ti45.5Ni45.5Al9中还生成了少量Ni2TiAl相;合金的抗弯强度随Al含量的提高而增加,并在Al含量为6%时达到最大值296.3 MPa;合金的硬度随铝含量的提高而增加,Ti45.5Ni45.5Al9的硬度值为295.6 HV。

关键词: TiNiAl合金, Al含量, 空心阴极等离子烧结, 微观组织, 力学性能

Abstract:

Ti50-x/2Ni50-x/2Alx(x=0, 3, 6, 9) intermetallic compounds with equal Ti/Ni atom ratio are fabricated through hollow cathode plasma sintering process, and the effect of Al content on the microstructure and mechanical properties of the alloys is investigated. The results show that the microstructure of an alloy without Al consists chiefly of the NiTi matrix, some strengthening phase Ti2Ni, Ni3Ti and some pores; with the addition and increase of the Al content, the amount of Ti2Ni(Al) increases while that of Ni3Ti(Al) decreases and a small amount of Ni2TiAl is formed in Ti45.5Ni45.5Al9, while the amount of pores and their sizes increase. The flexural strength of the alloys increases with increasing Al content and reaches the maximum of 296.3 MPa when Al content is 6%, and then it starts to decrease as Al content further increases. The hardness of the alloys increases with increasing Al content and the hardness of Ti45.5Ni45.5Al9 reaches 295.6 HV.

Key words: TiNiAl alloy, Al content, hollow cathode plasma sintering, microstructure, mechanical properties

中图分类号: