针刺C/C复合材料拉伸强度及渐进失效数值预测
收稿日期: 2016-01-03
修回日期: 2016-03-31
网络出版日期: 2016-04-21
基金资助
国家“973”计划（2011CB606105）
Numerical prediction of tensile strength and progressive damage of needled C/C composites
Received date: 2016-01-03
Revised date: 2016-03-31
Online published: 2016-04-21
Supported by
National Basic Research Program of China (2011CB606105)
基于金相显微镜观测的针刺C/C复合材料细观结构，考虑材料内部纤维的真实分布，建立了针刺C/C复合材料单胞模型。采用Linde失效准则，考虑纤维渐进损伤对材料进行了刚度折减，通过引入周期性位移边界条件，对针刺C/C复合材料的拉伸破坏进行了有限元法（FEM）数值模拟，分析了单胞模型的渐进失效过程，并预测了材料的拉伸强度。开展了针刺C/C复合材料拉伸试验，采用扫描电子显微镜（SEM）观察了材料的断口形貌，数值预测结果与试验吻合良好。针刺C/C复合材料受拉伸载荷后发生准脆性断裂，拉伸应力-应变曲线呈双线性，0°无纬碳布发生纤维断裂和基体开裂破坏，90°无纬碳布出现横向基体劈裂，最终断裂发生在针刺纤维与面内无纬碳布交叉区域。
谭勇洋 , 燕瑛 , 李欣 , 郭方亮 . 针刺C/C复合材料拉伸强度及渐进失效数值预测[J]. 航空学报, 2016 , 37(12) : 3734 -3741 . DOI: 10.7527/S1000-6893.2016.0107
Based on the observation of microstructures of needled C/C composites, a unit cell model which considered the true distribution of the fibers was established to predict the tensile strength and progressive damage. The finite element method (FEM) simulation of the tensile failure of the composites was conducted by using the failure criterion proposed by Linde and periodic displacement boundary conditions. The damage evolution of the composites was analyzed, which was subject to the longitudinal tensile load, and the tensile strength was predicted. By doing a quasi-static tensile test, the rupture surface of needled C/C composites was observed by scanning electron microscope (SEM). The numerical prediction was in good agreement with the test results. Quasi brittle fracture occurred under tensile load, and the stress-strain curve approximately presented bilinear shape. 0° weftless plies suffered from fiber breakage and matrix cracking damage, and 90° weftless plies from matrix damage. The final fracture occurred in the regions where the in-plain fiber and the needled fiber intersected.
Key words： needled C/C composites; unit cell model; tensile strength; progressive damage; FEM
[1] 刘建军, 李铁虎, 郝志彪, 等. 针刺炭布/网胎复合织物的组分形态及性能研究[J]. 固体火箭技术, 2005, 28(4):299-303. LIU J J, LI T H, HAO Z B, et al. Investigation on morphology and property of needled carbon cloth and web composite fabric[J]. Journal of Solid Rocket Technology, 2005, 28(4):299-303(in Chinese).
[2] 陈腾飞, 龚伟平, 黄伯云, 等. 航空刹车用炭/炭复合材料坯体结构研究进展[J]. 矿冶工程, 2005, 25(6):74-77. CHEN T F, GONG W P, HUANG B Y, et al. Advances in study of preform structure of C/C composites for aircraft brake discs[J]. Mining and Metallurgical Engineering, 2005, 25(6):74-77(in Chinese).
[3] 熊翔, 黄伯云, 肖鹏. 准三维C/C复合材料的压缩性能及其破坏机理[J]. 中南大学学报(自然科学版), 2004, 35(5):702-706. XIONG X, HUANG B Y, XIAO P. Compressive properties and fracture mechanism of quasi-3D C/C composites[J]. Journal of Central South University of Technology (Natural Science), 2004, 35(5):702-706(in Chinese).
[4] ZHANG J C, LUO R Y, XIANG Q, et al. Compressive fracture behavior of 3D needled-punched carbon/carbon composites[J]. Material Science and Engineering:A, 2011, 528(15):5002-5006.
[5] CAI Y Z, FAN S W, LIU H Y, et al. Mechanical properties of a 3D needled C/SiC composite with graphite filler[J]. Material Science and Engineering:A, 2010, 527(3):539-543.
[6] NIE J J, XU Y D, ZHANG L T. Microstructure and tensile behavior of multiply needled C/SiC composite fabricated by chemical vapor infiltration[J]. Journal of Materials Processing Technology, 2009, 209(1):572-576.
[7] NIE J J, XU Y D, MA J Q, et al. Effect of thermal cycling on modulus and tensile strength of 3D needled C/SiC composite in controlled environments[J]. Material Science and Engineering:A, 2008, 497(1-2):235-238.
[8] 李龙, 高希光, 史剑, 等. 考虑孔隙的针刺C/SiC复合材料弹性参数计算[J]. 航空动力学报, 2013, 28(6):1257-1263. LI L, GAO X G, SHI J, et al. Calculation of needled C/SiC composite elastic parameters in consideration of the porosity[J]. Journal of Aerospace Power, 2013, 28(6):1257-1263(in Chinese).
[9] XIE J B, LIANG J, FANG G D, et al. Effect of needling parameters on the effective properties of 3D needled C/C-SiC composites[J]. Composite Science and Technology, 2015, 117:69-77.
[10] 袁辉. 碳/碳复合材料刚度与强度预测模型研究[D]. 南京:南京航空航天大学, 2009:120-121. YUAN H. Research on prediction models for stiffness and strength of C/C composites[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2009:120-121(in Chinese).
[11] 张骥. 三维编织C/C复合材料断裂行为研究[D]. 哈尔滨:哈尔滨工业大学, 2012:9-50. ZHANG J. Research on the fracture behavior of three dimensional braided composites[D]. Harbin:Harbin Institute of Technology, 2012:9-50(in Chinese).
[12] 朱元林. 碳/碳复合材料疲劳寿命预测模型与分析方法研究[D]. 南京:南京航空航天大学, 2012:106-108. ZHU Y L. Research on prediction of damage failure and fatigue life for C/C composites[D]. Nanjing:Nanjing University of Aeronautics and Astronautics, 2012:106-108(in Chinese).
[13] LINDE P, PLEITNER J, BOER H D, et al. Modeling and simulation of fiber metal laminates[C]//ABAQUS User's Conference. Boston, MA:[s.n], 2004:421-439.
[14] ASTM. Standard test method for monotonic tensile behavior of continuous fiber-reinforced advanced ceramics with solid rectangular cross-section test specimens at ambient temperature:ASTM C1275-10[S]. West Conshohocken, PA:ASTM, 2010.
[15] 刘建军, 李铁虎, 郝志彪, 等. 针刺技术在C/C复合材料增强织物中的应用[J]. 宇航材料工艺, 2008(3):8-10. LIU J J, LI T H, HAO Z B, et al. Application of needling technology on reinforced fabrics of C/C composite materials[J]. Aerospace Materials & Technology, 2008(3):8-10(in Chinese).
[16] 赵渠森, 郭恩明. 先进复合材料手册[M]. 北京:机械工业出版社, 2003:275-284. ZHAO Q S, GUO E M. Handbook of advanced composite materials[M]. Beijing:China Machine Press, 2003:275-284(in Chinese).
[17] XIA Z H, ZHANG Y F, ELLYIN F. A unified periodical boundary conditions for representative volume elements of composites and applications[J]. International Journal of Solids and Structures, 2003, 40(8):1907-1921.
[18] XIA Z H, ZHOU C W, YONG Q L, et al. On selection of repeated unit cell model and application of unified periodic boundary conditions in micro-mechanical analysis of aomposites[J]. International Journal of Solids and Structures, 2006, 43(2):266-278.
[19] LI D S, LI J L, LU Z X, et al. Finete element analysis of mechanical properties of 3D four-directional rectangular braided composites Part 1:Microgeometry and 3D finite element model[J]. Applied Composites Materials, 2010, 17(4):389-404.
[20] 张超, 许希武, 毛春见. 三维编织复合材料渐进损伤模拟及强度预测[J]. 复合材料学报, 2011, 28(2):222-230. ZHANG C, XU X W, MAO C J. Progressive damage simulation and strength prediction of 3D braided composites[J]. Acta Materiae Compositae Sinica, 2011, 28(2):222-230(in Chinese).
/
| 〈 |
|
〉 |
CJA