航空学报 > 2026, Vol. 47 Issue (5): 332079-332079   doi: 10.7527/S1000-6893.2025.32079

全差分频率调制半球谐振陀螺装配误差辨识及补偿方法

王瑞祺1, 伊国兴1(), 解伟男1, 魏振楠1, 董圣为2   

  1. 1.哈尔滨工业大学 航天学院,哈尔滨 150001
    2.中国工程物理研究院 微系统与太赫兹研究中心,绵阳 621999
  • 收稿日期:2025-04-07 修回日期:2025-04-28 接受日期:2025-05-27 出版日期:2025-06-16 发布日期:2025-06-05
  • 通讯作者: 伊国兴 E-mail:ygx@hit.end.cn;ygx@hit.edu.cn
  • 基金资助:
    国家自然科学基金(62403161);黑龙江省博士后资助项目(LBH-Z22134)

Identification and compensation method for assembly errors in fully differential frequency-modulated hemispherical resonator gyroscope

Ruiqi WANG1, Guoxing YI1(), Weinan XIE1, Zhennan WEI1, Shengwei DONG2   

  1. 1.School of Astronautics,Harbin Institute of Technology,Harbin 150001,China
    2.Microsystem and Terahertz Research Center,China Academy of Engineering Physics,Mianyang 621999,China
  • Received:2025-04-07 Revised:2025-04-28 Accepted:2025-05-27 Online:2025-06-16 Published:2025-06-05
  • Contact: Guoxing YI E-mail:ygx@hit.end.cn;ygx@hit.edu.cn
  • Supported by:
    National Natural Science Foundation of China(62403161);Heilongjiang Provincial Postdoctoral Funding Project(LBH-Z22134)

摘要:

针对全差分频率调制半球谐振陀螺因装配误差引起的性能退化,从信号处理的角度提出一种基于非线性优化的装配误差同步辨识及补偿方法。首先,建立了分时复用控制方案下装配姿态误差与通道耦合误差的系统性关联模型,分析了安装倾斜和安装偏心对通道耦合误差的影响机制。在此基础上,建立了包含通道耦合误差的半球谐振陀螺动态输出模型,揭示了载体转速与陀螺输出谐波分量的耦合效应。最后,提出一种基于非线性优化的装配误差同步辨识及补偿方法。实验结果表明,装配误差补偿后,陀螺的标度因数非线性和周向漂移稳定性分别降低了91.97%和51.25%,仅为6.94×10-7和0.398 (°)/h。该方法显著提升了陀螺在动态及静态环境下的性能指标,为高精度半球谐振陀螺的设计与优化提供了理论支撑。

关键词: 半球谐振陀螺, 装配误差, 频率调制, 分时复用, 误差辨识及补偿

Abstract:

To address the performance degradation of fully differential frequency-modulated Hemispherical Resonator Gyroscope (HRG) caused by assembly errors, this paper proposes a synchronous identification and compensation method for assembly errors based on nonlinear optimization from a signal processing perspective. First, a systematic correlation model between the assembly attitude errors and channel coupling errors under the time-division multiplexing control scheme is established, and the influence mechanisms of installation tilt and installation eccentricity on channel coupling errors are analyzed. On this basis, a dynamic output model of the HRG incorporating channel coupling errors is developed, revealing the coupling effect between the carrier rotation rate and the harmonic components of the gyroscope output. Finally, a synchronous identification and compensation method for assembly errors based on nonlinear optimization is proposed. Experimental results demonstrate that after compensating for assembly errors, the scale factor nonlinearity and circumferential drift stability of the gyroscope are reduced by 91.97% and 51.25%, respectively, reaching only 6.94×10-7 and 0.398 (°)/h. This method significantly improves the gyroscope’s performance in both dynamic and static environments, providing theoretical support for the design and optimization of the high-precision HRG.

Key words: hemispherical resonator gyroscope, assembly errors, frequency-modulation, time-division multiplexing, error identification and compensation

中图分类号: