ACTA AERONAUTICAET ASTRONAUTICA SINICA >
Flow and heat transfer characteristics of radial flow sector plate-fin evaporator
Received date: 2026-01-23
Revised date: 2026-02-26
Accepted date: 2026-04-28
Online published: 2026-04-30
To address the thermal management requirements of high-heat-flux electronic equipment in aerospace applications， a radial-flow sector-shaped plate-fin evaporator operating under consumable cooling conditions was investigated. The key structural parameters of the evaporator were preliminarily selected through numerical simulations. An open-loop experimental platform was established， utilizing an antifreeze fluid loop to simulate onboard thermal loads， enabling experimental testing of the flow and heat transfer characteristics of the expendable evaporator under typical operating conditions. The experimental results indicate that the impact of flow direction on the performance of radial flow sector plate fin evaporators exhibits significant dependence on operational conditions， with distinct crossover features between parallel flow and counter flow observed in medium-low and high thermal load ranges. In low-medium thermal load ranges， parallel flow demonstrates superior heat exchange performance due to the maximum initial temperature difference at the inlet section of the flow channel. However， under high thermal loads， counter flow surpasses due to its ability to sustain continuous and stable heat transfer driving forces and liquid phase wetting conditions in the latter half of the flow channel. Combined with numerical simulations， the mechanisms of two flow directions-parallel and counter flow-on the flow and heat transfer characteristics were systematically studied. Through analysis of temperature fields， gas phase volume fractions， and velocity fields， it was found that the primary cause of performance differences lies in the different axial temperature matching relationships between hot and cold fluids established by the two flow modes. Counter flow， through its inherent reverse temperature profile characteristics， extends the length of liquid film wetting， optimizing the heat transfer process in high heat flux regions. This research provides experimental evidence and theoretical references for the design and operation methods of evaporators targeting high heat flux dissipation scenarios.
Mengnan LIU , Liping PANG , Lin MIAO , Kai ZHANG , Zhiren YIN . Flow and heat transfer characteristics of radial flow sector plate-fin evaporator[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2026 , 47(13) : 533413 -533413 . DOI: 10.7527/S1000-6893.2026.33413
| [1] | ERSOY K. Review of electronic cooling and thermal management in space and aerospace applications［C］∥ 2024 IEEE 7th International Conference on Knowledge Innovation and Invention. Basel： MDPI， 2025： 42. |
| [2] | ESSER B， BARCENA J， KUHN M， et al. Innovative thermal management concepts and material solutions for future space vehicles［J］. Journal of Spacecraft and Rockets， 2016， 53（6）： 1051-1060. |
| [3] | KANDLIKAR S G. High flux heat removal with microchannels： A roadmap of challenges and opportunities［J］. Heat Transfer Engineering， 2005， 26（8）： 5-14. |
| [4] | MUDAWAR I. Assessment of high-heat-flux thermal management schemes［J］. IEEE Transactions on Components and Packaging Technologies， 2001， 24（2）： 122-141. |
| [5] | SUNDéN B， ABBOOD S A， WU Z. Effects of engineered micro/nanostructures on nucleate pool boiling heat transfer［J］. Nanoscience & Nanotechnology-Asia， 2017， 7（2）： 155-161. |
| [6] | BERTSCH S S， GROLL E A， GARIMELLA S V. Refrigerant flow boiling heat transfer in parallel microchannels as a function of local vapor quality［J］. International Journal of Heat and Mass Transfer， 2008， 51（19-20）： 4775-4787. |
| [7] | HANFORD A J， EWERT M K. Advanced active thermal control systems architecture study： NASA-TM-104822［R］. Washington， D.C.： NASA， 1996. |
| [8] | KHORRAMMANESH M， AMIDPOUR M， NASR M R J. Application of process decomposition in multi-stream plate fin heat exchangers design to use in heat recovery networks［J］. Chemical Engineering and Processing - Process Intensification， 2007， 46（10）： 941-954. |
| [9] | 米廷灿， 厉彦忠， 王江， 等. 一种计算板翅式换热器二次表面换热的新模型［J］. 西安交通大学学报， 2004， 38（5）： 496-499. |
| MI T C， LI Y Z， WANG J， et al. New model computing the secondary surface heat exchange of plate-fin heat exchanger［J］. Journal of Xi’an Jiaotong University， 2004， 38（5）： 496-499 （in Chinese）. | |
| [10] | CHANG H M， GWAK K H. New application of plate-fin heat exchanger with regenerative cryocoolers［J］. Cryogenics， 2015， 70： 1-8. |
| [11] | FERU E， DE JAGER B， WILLEMS F， et al. Two-phase plate-fin heat exchanger modeling for waste heat recovery systems in diesel engines［J］. Applied Energy， 2014， 133： 183-196. |
| [12] | LIU C B， BU W Y， XU D. Multi-objective shape optimization of a plate-fin heat exchanger using CFD and multi-objective genetic algorithm［J］. International Journal of Heat and Mass Transfer， 2017， 111： 65-82. |
| [13] | ZHENG X Y， QI Z G. A comprehensive review of offset strip fin and its applications［J］. Applied Thermal Engineering， 2018， 139： 61-75. |
| [14] | YANG Y J， LI Y Z. General prediction of the thermal hydraulic performance for plate-fin heat exchanger with offset strip fins［J］. International Journal of Heat and Mass Transfer， 2014， 78： 860-870. |
| [15] | YANG Y J， LI Y Z， SI B， et al. Performance evaluation of heat transfer enhancement for offset strip fins used in plate-fin heat exchangers［J］. Journal of Heat Transfer， 2015， 137（10）： 101901. |
| [16] | KAYS W M， LONDON A L. Compact heat exchangers ［M］. 3rd ed. New York： McGraw-Hill， 1984： 10-48. |
| [17] | WIETING A R. Empirical correlations for heat transfer and flow friction characteristics of rectangular offset-fin plate-fin heat exchangers［J］. Journal of Heat Transfer， 1975， 97（3）： 488-490. |
| [18] | MANGLIK R M， BERGLES A E. Heat transfer and pressure drop correlations for the rectangular offset strip fin compact heat exchanger［J］. Experimental Thermal and Fluid Science， 1995， 10（2）： 171-180. |
| [19] | RANGANAYAKULU C， KABELAC S. Boiling of R134a in a plate-fin heat exchanger having offset fins［J］. Journal of Heat Transfer， 2015， 137（12）： 121002. |
| [20] | LI J R， HU H T， ZHANG Y H. Experimental investigation and correlation development for two-phase pressure drop characteristics of flow boiling in offset strip fin channels［J］. International Journal of Thermal Sciences， 2021， 160： 106693. |
| [21] | PULVIRENTI B， MATALONE A， BARUCCA U. Boiling heat transfer in narrow channels with offset strip fins： Application to electronic chipsets cooling［J］. Applied Thermal Engineering， 2010， 30（14-15）： 2138-2145. |
| [22] | JOUHARA H， ALMAHMOUD S， BROUGH D， et al. Experimental and theoretical investigation of the performance of an air to water multi-pass heat pipe-based heat exchanger［J］. Energy， 2021， 219： 119624. |
| [23] | MA D S， PANG L P， ZHANG Y D. Experimental study on low pressure heat transfer properties of water evaporator with screen separation element［J］. International Journal of Thermal Sciences， 2023， 193： 108492. |
| [24] | GUO Z Y， LIU X B， TAO W Q， et al. Effectiveness-thermal resistance method for heat exchanger design and analysis［J］. International Journal of Heat and Mass Transfer， 2010， 53（13-14）： 2877-2884. |
| [25] | MOREIRA T A， MORSE R W， DRESSLER K M， et al. Liquid-film thickness and disturbance-wave characterization in a vertical， upward， two-phase annular flow of saturated R245fa inside a rectangular channel［J］. International Journal of Multiphase Flow， 2020， 132： 103412. |
| [26] | MOFFAT R J. Describing the uncertainties in experimental results［J］. Experimental Thermal and Fluid Science， 1988， 1（1）： 3-17. |
/
| 〈 |
|
〉 |
CJA