ACTA AERONAUTICAET ASTRONAUTICA SINICA >
Test of boiling heat transfer in rectangular channels with offset fins
Received date: 2016-04-19
Revised date: 2016-08-31
Online published: 2016-09-28
A boiling heat transfer test system is built to investigate the boiling heat transfer characteristics of two kinds of rectangular channels with offset fins,with R134a as the working medium. The hydraulic diameters of the channels are 1.28 mm and 1.59 mm. The experiments are performed at mass flow rate of refrigerant between 68.5 and 305.5 kg/(m2·s), heat flux between 9 and 42 kW/m2, and saturation pressure between 0.27 and 0.45 MPa, with constant heat flux heating mode. The results show that the channel with smaller hydraulic diameter has stronger heat transfer capability. The influences of heat flux and saturation pressure on boiling heat transfer are related to a value of vapor quality. If the vapor quality is less than this value, the increase of heat flux or saturation pressure would lead to the increase of heat transfer coefficients. If the vapor quality is greater than this value, the boiling heat transfer coefficient will sharply decrease with the increase of vapor quality, and the influences of heat flux and saturation pressure will be much weaker. The value will gradually decrease with the increase of heat flux or saturation pressure. The effect of mass flow rate on boiling heat transfer is related to heat flux. With the increase of heat flux, the influence of mass flow rate tends to the region with greater vapor quality. On the basis of the analysis of these parameters, a new correlation is proposed to predict the boiling heat transfer coefficients of the small sized channels with offset fins under the experimental conditions.
ZHAN Hongbo , WEN Tao , ZHANG Dalin . Test of boiling heat transfer in rectangular channels with offset fins[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2017 , 38(3) : 120329 -120329 . DOI: 10.7527/S1000-6893.2016.0248
[1] OH J T, PAMITRAN A S, CHOI K I, et al. Experimental investigation on two-phase flow boiling heat transfer of five refrigerants in horizontal small tubes of 0.5, 1.5 and 3.0 mm inner diameters[J]. International Journal of Heat & Mass Transfer, 2011, 54(s 9-10):2080-2088.
[2] COPETTI J B, MACAGNAN M H, ZINANI F, et al. Flow boiling heat transfer and pressure drop of R-134a in a mini tube:an experimental investigation[J]. Experimental Thermal & Fluid Science, 2011, 35(4):636-644.
[3] TIBIRICA C B, RIBATSKI G. Flow boiling heat transfer of R134a and R245fa in a 2.3 mm tube[J]. International Journal of Heat & Mass Transfer, 2010, 53(s 11-12):2459-2468.
[4] SHIFERAW D, KARAYIANNISS T G, KENNING D B R. Flow boiling in a 1.1 mm tube with R134a:Experimental results and comparison with model[J]. International Journal of Thermal Sciences, 2009, 48(2):331-341.
[5] 余建祖. 换热器原理与设计[M]. 北京:北京航空航天大学出版社, 2006:43-44. YU J Z. Principle and design of heat exchanger[M]. Beijing:Beihang University Press, 2006:43-44(in Chinese).
[6] DUBROVSKY E V, VASILIEV V Y. Enhancement of convective heat transfer in rectangular ducts of interrupted surfaces[J]. International Journal of Heat & Mass Transfer, 1988, 31(4):807-818.
[7] MOCHIZUKI S, YAGI Y, YANG W J. Transport phenomena in stacks of interrupted parallel-plate surfaces[J]. Experimental Heat Transfer, 1987, 1(2):127-140.
[8] MANGLIK R M, BERGLES A E. Heat transfer and pressure drop correlations for the rectangular offset strip fin compact heat exchanger[J]. Experimental Thermal & Fluid Science, 1995, 10(2):171-180.
[9] PULVIRENTI B, MATALONE A, BARUCCA U. Boiling heat transfer in narrow channels with offset strip fins:Application to electronic chipsets cooling[J]. Applied Thermal Engineering, 2010, 30(s 14-15):2138-2145.
[10] KIM B, SOHN B. An experimental study of flow boiling in a rectangular channel with offset strip fins[J]. International Journal of Heat & Fluid Flow, 2006, 27(3):514-521.
[11] CHOI K I, PAMITRAN A S, OH C Y, et al. Boiling heat transfer of R-22, R-134a, and CO2 in horizontal smooth minichannels[J]. International Journal of Refrigeration, 2007, 30(8):1336-1346.
[12] YEN T H, KASAGI N, SUZUKI Y. Forced convective boiling heat transfer in microtubes at low mass and heat fluxes[J]. International Journal of Multiphase Flow, 2003, 29(12):1771-1792.
[13] BERTSCH S S, GROLL E A, GARIMELLA S V. Effects of heat flux, mass flux, vapor quality, and saturation temperature on flow boiling heat transfer in microchannels[J]. International Journal of Multiphase Flow, 2009, 35(2):142-154.
[14] VAKILI-FARAHANI F, AGOSTINI B, THOME J R. Experimental study on flow boiling heat transfer ofmultiport tubes with R245fa and R1234ze(E)[J]. International Journal of Refrigeration, 2013, 36(2):335-352.
[15] BERTSCH S S, GROLL E A, GARIMELLA S V. A composite heat transfer correlation for saturated flow boiling in small channels[J]. International Journal of Heat & Mass Transfer, 2009, 52(7-8):2110-2118.
[16] 凯斯W M, 伦敦A L. 紧凑式热交换器[M]. 北京:科技出版社, 1997:285-326. KAYS W M, LONDON A L. Compact heat exchangers[M]. Beijing:Science and Technology Press, 1997:285-326(in Chinese).
[17] FELDMAN A, MARVILLET C, LEBOUCHE M. Nucleate and convective boiling in plate fin heat exchangers[J]. International Journal of Heat & Mass Transfer, 2000, 43(18):3433-3442.
[18] LIU Z, WINTERTON R H S. A general correlation for saturated and subcooled flow boiling in tubes and annuli, based on a nucleate pool boiling equation[J]. International Journal of Heat & Mass Transfer, 1991, 34(11):2759-2766.
[19] KEW P A, CORNWELL K. Correlations for the prediction of boiling heat transfer in small-diameter channels[J]. Applied Thermal Engineering, 1997, 17(8-10):705-715.
[20] FANG X. A new correlation of flow boiling heat transfer coefficients based on R134a data[J]. International Journal of Heat & Mass Transfer, 2013, 66(6):279-283.
/
| 〈 |
|
〉 |
CJA