ACTA AERONAUTICAET ASTRONAUTICA SINICA >
Dynamic effect of time-variant wear clearance on mechanical reliability
Received date: 2014-05-05
Revised date: 2014-06-23
Online published: 2015-05-15
Supported by
National Basic Research Program of China (2013CB733000)
In order to overcome the drawbacks of constant wear rate and wear factors randomness hypothesis and to accurately predict the dynamic process of mechanical wear reliability, a time-variant wear equation of joint clearance is constructed by using a nonlinear equivalent spring-damp contact force model and discretization of wear process. Then, the joint wear evolution equation is converted into a time-dependent reliability equation by introducing a PHI2 method and defining an up-crossing rate. Therefore, a wear reliability analysis method which combines the mechanical multibody dynamics considering time-variant clearance with PHI2 is put forward. At last, by taking a two-axis positioning mechanism of satellite antennas as an example,dynamic reliability of the mechanism, parameters reliability sensitivity and their influence on reliability are studied. Results show that contact force is the dominant factor of reliability which is 10 times sensitive than other factors before the end of the product's steady wear process stage, while joint clearance will be the new dominant factor of reliability after this stage. What's more, there is a critical value for joint clearance, and appropriate augmentation of joint clearance before this critical value is propitious to the improvement of product's reliability. Compared to the current methods where randomness is emphasized, while the nonlinear process of wear and the consequence of concomitant time-variant clearances to product reliability are neglected, the present method could accurately analyze the dynamic process of wear and wear reliability.
Key words： clearance; wear; reliability; multibody dynamics; positioning mechanisms; satellite antennas
LIU Yuqiang , TAN Chunlin , ZHAO Yang . Dynamic effect of time-variant wear clearance on mechanical reliability[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2015 , 36(5) : 1539 -1547 . DOI: 10.7527/S1000-6893.2014.0129
[1] Flores P. A parametric study on the dynamic response of planar multibody system with multiple clearance joints[J]. Nonlinear Dynamics, 2010, 61(4): 633-653.
[2] Mukras S, Kim N H, Mauntler N A, et al. Analysis of planar multibody systems with revolute joint wear[J]. Wear, 2010, 268(5-6): 643-652.
[3] Erkaya S. Prediction of vibration characteristics of a planar mechanism having imperfect joints using neural network[J]. Journal of Mechanical Science and Technology, 2012, 26(5): 1419-1430.
[4] Xu L X, Yang Y H, Liu Y G, et al. Modeling and analysis of planar multibody systems containing deep groove ball bearing with clearance[J]. Mechanism and Machine Theory, 2012, 56(10): 69-88.
[5] Bai Z F, Zhao Y, Chen J. Dynamics analysis of planar mechanical system considering revolute clearance joint wear[J]. Tribology International, 2013, 64(8): 85-95.
[6] Bai Z F, Zhao Y, Wang X G. Wear analysis of revolute joints with clearance in multibody systems[J]. Science China—Physics Mechanics Astronomy, 2013, 56(8): 1581-1590.
[7] Muvengei O, Kihiu J, Ikua B. Dynamic analysis of planar rigid-body mechanical systems with two-clearance revolute joints[J]. Nonlinear Dynamics, 2013, 73(1-2): 259-273.
[8] Papadrakakis M, Lagaros N D. Reliability based structural optimization using neural networks and Monte Carlo simulation[J]. Computer Methods in Applied Mechanics and Engineering, 2002, 191(32): 3491-3507.
[9] Marko C, Bornt M. A dynamic fault tree[J]. Reliability Engineering and System Safety, 2002, 75(1): 83-91.
[10] Wu Z L, Guo C, Zhao H. Reliability-modeling for the repairable system based on Markov process[J]. Journal of Dalian Maritime University, 2007, 33(1): 13-16 (in Chinese). 吴志良, 郭晨, 赵红. 基于马尔柯夫过程的可修复系统可靠性建模[J]. 大连海事大学学报, 2007, 33(1): 13-16.
[11] Muhammad H, Hidekazu Y, Takeshi M, et al. Common cause failure analysis of PWR containment spray system by GO-FLOW methodology[J]. Nuclear Engineering and Design, 2013, 262(9): 350-357.
[12] Adamyan A,He D.Analysis of sequential failures for assessment of reliability and safety of manufacturing systems[J]. Reliability Engineering and System Safety, 2002, 76(3): 227-236.
[13] Su C, Shen G. Development for system reliability modeling and simulation based on generalized stochastic Petri net (GSPN)[J]. MIE of China, 2007, 36(9): 45-48 (in Chinese). 苏春, 沈戈. 基于广义随机Petri网的系统可靠性建模与仿真软件开发[J]. 中国制造业信息化, 2007, 36(9): 45-48.
[14] Wang Z, Xie L Y. Time-variant reliability model of components under uncertain loads[J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(7): 1241-1247 (in Chinese). 王正, 谢里阳. 不确定性载荷作用下的零件时变可靠性模型[J]. 航空学报, 2009, 30(7): 1241-1247.
[15] Mejri M, Cazuguel M, Cognard J Y. A time-variant reliability approach for ageing marine structures with non-linear behavior[J]. Computers & Structures, 2011, 89(19-20): 1743-1753.
[16] Sudret B. Analytical derivation of the outcrossing rate in time-variant reliability problems[J]. Structure and Infrastructure Engineering, 2008, 4(5): 353-362.
[17] Wan Z Y, Zhao X, Li W C. Analysis of the motion reliability based on the effective length model of continuous contact and the Archard's wear theory[J]. Mechanical Science and Technology for Aerospace Engineering, 2013, 32(5): 679-682 (in Chinese). 万朝燕, 赵旭, 李文成. 基于连续接触"有效长度模型"及Archard磨损的运动可靠性分析[J]. 机械科学与技术, 2013, 32(5): 679-682.
[18] Tong C H, Huang J L, Hu Y X. Reliability analysis of mechanism motion based on both wear of a kinematic pair and its original error[J]. Journal of Lanzhou University of Technology, 2010, 36(2): 33-37 (in Chinese). 同长虹, 黄建龙, 胡玉霞. 基于运动副磨损和原始误差影响的机构运动可靠性分析[J]. 兰州理工大学学报, 2010, 36(2): 33-37.
[19] Lin H B, Cai J, Xu Y M. A study on wear reliability of mechanism based on performance degradation[J]. Aircraft Design, 2012, 32(5): 46-49 (in Chinese). 林海彬, 蔡景, 徐一鸣. 基于性能退化的机构磨损可靠性研究[J]. 飞机设计, 2012, 32(5): 46-49.
[20] Liu Q, Li J, Liu Y. Modeling and example analysis of wear random process[J]. Acta Armamentarii, 2010, 31(10): 1379-1382 (in Chinese). 刘勤, 李娟, 刘英. 磨损随机过程建模及实例分析[J].兵工学报, 2010, 31(10): 1379-1382.
[21] Andrieu-Renaud C, Sudret B, Lemaire M. The PHI2 method: a way to compute time-variant reliability[J]. Reliability Engineering & System Safety, 2004, 84(1): 75-86.
[22] Zhao Y, Bai Z F, Wang X G. Dynamics analysis of two-axis position mechanism of satellite antennas with joint clearance[J]. Journal of Astronautics, 2010, 31(6): 1533-1539 (in Chinese). 赵阳, 白争锋, 王兴贵. 含间隙卫星天线双轴定位机构动力学仿真分析[J]. 宇航学报, 2010, 31(6): 1533-1539.
[23] Gupta P K. Tribological modeling, ADA372092[R]. New York: PKG Inc., 1998.
[24] Sheng J, Xie S Q, Pan C Y. Probability and mathematical statistics[M]. 4th ed. Beijing: Higher Education Press, 2008: 382 (in Chinese). 盛聚, 谢式千, 潘承毅. 概率论与梳理统计[M]. 4版. 北京: 高等教育出版社, 2008: 382.
[25] Zhao M Y, Feng Y S. The computation of wear reliability of mechanism with high accuracy[J]. Journal of Mechanical Strength, 1998, 20(1): 49-52 (in Chinese). 赵美英, 冯元生. 机构磨损可靠性高精度算法[J]. 机械强度, 1998, 20(1): 49-52.
/
| 〈 |
|
〉 |
CJA