ACTA AERONAUTICAET ASTRONAUTICA SINICA >
Numerical Simulation of Hydrostatic Bearing with Self-controlled Restrictor Employing Cooling Roll in Amorphous Alloy Ribbon Formation
Received date: 2013-06-07
Revised date: 2013-07-09
Online published: 2013-07-12
Hydrostatic bearings with self-controlled restrictors are used for cooling roll support structures in amorphous alloy ribbon formation due to their large load capacity, high bearing stiffness and low friction characteristics. The finite volume method is used to compute the three-dimensional fluid pressure field of the bearing models of different eccentricities to obtain the bearing characteristics. This study analyzes theoretically the influence of different eccentricities on bearing performance according to computational fluid dynamics. The simulation results demonstrate that the load capacity of the bearing increases gradually with the increase of eccentricity at the same supplied pressure. And the increase of supplied pressure results in the enlargement of the load capacity with the same eccentricity. In comparison with the real value of the load, the relative errors of simulation data are respectively 5.3% and 5.4% with the supplied pressure of 3.0 MPa and 3.5 MPa. Through this study, the validity of the numerical simulation of hydrostatic bearings is verified.
SONG Yanming , YANG Yang . Numerical Simulation of Hydrostatic Bearing with Self-controlled Restrictor Employing Cooling Roll in Amorphous Alloy Ribbon Formation[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2014 , 35(4) : 1157 -1164 . DOI: 10.7527/S1000-6893.2013.0337
[1] Wang X W, Liu G Y. Amorphous alloy pressure sensors and transducers[J]. Acta Aeronautica et Astronautica Sinica, 1988, 9(4): 115-122. (in Chinese) 王绪威, 刘广玉. 非晶态合金压力敏感元件和传感器[J]. 航空学报, 1988, 9(4): 115-122.
[2] Yang Y R, Wang Y Y, Li Y, et al. Microstructure and magnetic anisotropy of FeCoNbB films[J]. Chinese Journal of Aeronautics, 2011, 24(6): 823-828.
[3] Hui X D, Yang Y S, Chen X M. Numerical simulation of heat transfer and fluid flow during preparing amorphous alloy by single-roller spinning[J]. Acta Metallurgica Sinica, 1999, 35(11): 1206-1210. (in Chinese) 惠希东, 杨院生, 陈晓明. 单辊法制备非晶合金的传热与熔体流动数值模拟[J]. 金属学报, 1999, 35 (11): 1206-1210.
[4] Bizen Y, Nagao M, Sunakawa J. Method for producing amorphous alloy ribbon and method for producing nano-crystalline alloy ribbon with same: United States, ZL6749700B2. 2004-07-15.
[5] Takecchi S, Kakegawa T, Hashimoto T. Low temperature mechanical properties of bulk metallic glasses[J]. Materials Transcations, 2000, 41(11): 1443-1447.
[6] Takeshita K, Shigu P H. An analysis of the ribbon formation process by the single roller rapid solidification technique[J]. Transaction of the Japan Institute of metals, 1983, 24(7): 529-536.
[7] Yan Z T. The automatic control and computer management system of one-thousand ton level amorphous ribbon production line. Beijing: School of Electronic Information and Control Engineering, Beijing University of Technology, 2000. (in Chinese) 阎仲亭. 千吨级非晶带材生产自动控制及计算机管理系统. 北京: 北京工业大学电子信息与控制工程学院, 2000.
[8] Kumar M, Kim D. Static performance of hydrostatic air bump foil bearing[J]. Tribology International, 2010, 43(4): 752-758.
[9] Sharma S C, Phalle V M, Jain S C. Performance analysis of a multirecess capillary compensated conical hydrostatic journal bearing[J]. Tribology International, 2011, 44(5): 617-626.
[10] Sawicki J T, Capaldi R J, Adams M L. Experimental and theoretical rotordynamic characteristics of a hybrid journal bearing[J]. Transactions of the ASME, 1997, 119(1): 132-141.
[11] Zhao G, Liu P N, Yu H C. Research on gas film force of aerostatic gas bearing and its coupled dynamics with rotor[J]. Journal of Aerospace Power, 2012, 27(2): 472-480. (in Chinese) 赵广, 刘盼年, 于贺春. 静压气体轴承气膜力及其与转子耦合动力学特性研究[J]. 航空动力学报, 2012, 27(2): 472-480.
[12] Hu Y, Balendra R. CFD analysis on the lubrication behaviors of journal bearing with dimples//Proceedings of 2009 International Conference on Mechatronics and Automation, 2009.
[13] Bompos D A, Nikolakopoulos P G. CFD simulation of magnetorheological fluid journal bearings[J]. Simulation Modelling Practice and Theory, 2011, 19(4): 1035-1060.
[14] Zhang Y Q, Fan L G, Li R, et al. Simulation and experimental analysis of supporting characteristics of multiple oil pad hydrostatic bearing disk[J]. Journal of Hydrodynamics, 2013, 25(2): 236-241.
[15] Lu L H, Su H, Liang Y C, et al. Research on static stiffness of hydrostatic bearing using fluid-structure interaction analysis[J]. Procedia Engineering, 2012, 29: 1304-1308.
[16] Du Q L, Zhang K H. Numerical analysis of load-bearing capacity of oil film for hydro-hybrid bearing using finite element method[J]. Transactions of the Chinese Society of Agricultural Engineering, 2008, 24 (6): 137-140.(in Chinese) 杜巧莲, 张克华. 动静压液体轴承油膜承载特性的数值分析[J]. 农业工程学报, 2008, 24(6): 137-140.
[17] Shao J P, Dai C X, Zhang Y Q, et al. The effect of oil cavity depth on temperature field in heavy hydrostatic thrust bearing[J]. Journal of Hydrodynamics, Ser.B, 2011, 23(5): 676-680.
/
| 〈 |
|
〉 |
CJA