倾斜射流撞壁铺展的数值仿真

doi:10.7527/S1000-6893.2021.26428

Abstract

Abstract:

In order to deepen the understanding of the liquid film formed by the spreading of the jet impinging onto the plate， the numerical simulation of the oblique jet impinging onto the wall was carried out in this paper. The two-phase numerical simulation of the liquid film spreading process after the jet impinge onto the wall was carried out using mesh adaptive method. The spreading process， flow field structure and local flow characteristics of the wall impingement zone were obtained and analyzed under typical working conditions. The key characteristics of the liquid film can be clearly identified from numerical simulation results， and the comparison with the experimental results also shows the feasibility and accuracy of the numerical simulation method. Through numerical simulation， it is found that after the jet impinges onto the wall， the flow takes the stagnation point as the center and spreads around in a radial structure. After merging into the hydraulic-jump zone at the edge of the liquid film， the flow direction deflects and continues to flow downstream. This is the basic process of the jet impinging the wall and spreading to form the liquid sheet. Inertial force drives the liquid film to radiate outward and spread out. Then， under the influence of the surface tension and surface contact angle at the edge of the liquid film， a high pressure zone of the liquid film is formed and pushes the liquid film to shrink. The inertia force of the liquid film decreases gradually under the shear action of the wall until it is in balance with other forces such as the surface tension at the edge of the liquid film. Thus， the boundary of the liquid film is determined. The numerical simulation results also verify that the stagnation point of the flow in the impingement zone is near a focal point of the elliptical contact surface between the jet and the wall.

Key words: oblique jet, liquid film, jet impinging onto a wall, spread of liquid film, mesh adaptive method

CLC Number:

V434⁺.14

Liang TANG, Kai WANG, Wenlong LI, Yazhou LIU, Botao ZHANG, Xiaowen REN. Numerical simulation on spreading of oblique jet impinging onto a wall[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2023, 44(4): 126428.

Figures/Tables 16

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Table 1

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 13

Fig. 14

Fig. 15

References 34

1	唐亮，李平，周立新. 液体火箭发动机液膜冷却研究综述［J］. 火箭推进， 2020， 46（1）： 1-12.
	TANG L， LI P， ZHOU L X. Review on liquid film cooling of liquid rocket engine［J］. Journal of Rocket Propulsion， 2020， 46（1）： 1-12 （in Chinese）.
2	张锋，仲伟聪. 膜冷却推力室传热计算研究［J］. 火箭推进， 2009， 35（4）： 34-37， 48.
	ZHANG F， ZHONG W C. Computational investigation of heat transfer for film cooling thrust chamber［J］. Journal of Rocket Propulsion， 2009， 35（4）： 34-37， 48 （in Chinese）.
3	吴凌峰，杨成虎，姚锋，等. 单股自由圆射流撞壁雾化实验［J］. 火箭推进， 2020， 46（1）： 44-51.
	WU L F， YANG C H， YAO F， et al. Atomization experiment of single free circular jet impinging against wall［J］. Journal of Rocket Propulsion， 2020， 46（1）： 44-51 （in Chinese）.
4	ARAKERI J， RAO K P. On radial film flow on a horizontal surface and the circular hydraulic jump［J］. Journal of the Indian Institute of Science， 2013， 76： 73-91.
5	BLACKFORD B L. The hydraulic jump in radially spreading flow： A new model and new experimental data［J］. American Journal of Physics， 1996， 64（2）： 164-169.
6	BOHR T， DIMON P， PUTKARADZE V. Shallow-water approach to the circular hydraulic jump［J］. Journal of Fluid Mechanics， 1993， 254： 635-648.
7	BOUAINOUCHE M， BOURABAA N， DESMET B. Numerical study of the wall shear stress produced by the impingement of a plane turbulent jet on a plate［J］. International Journal of Numerical Methods for Heat & Fluid Flow， 1997， 7（6）： 548-564.
8	BRECHET Y， NÉDA Z. On the circular hydraulic jump［J］. American Journal of Physics， 1999， 67（8）： 723-731.
9	BUSH J W M， ARISTOFF J M. The influence of surface tension on the circular hydraulic jump［J］. Journal of Fluid Mechanics， 2003， 489： 229-238.
10	KIBAR A， KARABAY H， YIĞIT K S， et al. Experimental investigation of inclined liquid water jet flow onto vertically located superhydrophobic surfaces［J］. Experiments in Fluids， 2010， 49（5）： 1135-1145.
11	林庆国. 空间轨控发动机高效燃烧室仿真与试验研究［D］. 长沙：国防科技大学， 2015.
	LIN Q G. Simulation and experiment research on the high efficient combustion chamber for space orbit maneuvering rocket engine［D］. Changsha： National University of Defense Technology， 2015 （in Chinese）.
12	GOOD R， NOLLET B. Fluid film distribution investigation for liquid film cooling application： AIAA-2017-4920［R］. Reston： AIAA， 2017.
13	HASSON D， PECK R E. Thickness distribution in a sheet formed by impinging jets［J］. American Institute of Chemical Engineers Journal， 1964， 10（5）： 752-754.
14	BREMOND N， VILLERMAUX E. Atomization by jet impact［J］. Journal of Fluid Mechanics， 2006， 549： 273-306.
15	YANG L J， ZHAO F， FU Q F， et al. Liquid sheet formed by impingement of two viscous jets［J］. Journal of Propulsion and Power， 2014， 30（4）： 1016-1026.
16	YANG L J， LI P H， FU Q F. Liquid sheet formed by a Newtonian jet obliquely impinging on pro/hydrophobic surfaces［J］. International Journal of Multiphase Flow， 2020， 125： 103192.
17	唐亮，胡锦华，刘计武，等. 倾斜射流撞壁实验研究及液膜几何参数建模［J］. 航空学报， 2020， 41（12）： 124601.
	TANG L， HU J H， LIU J W， et al. Experimental study on oblique jet wall impingement and geometrical parameter modeling of liquid film［J］. Acta Aeronautica et Astronautica Sinica， 2020， 41（12）： 124601 （in Chinese）.
18	唐亮，李平，周立新，等. 倾斜射流撞壁形成的液膜外形的理论建模［J］. 推进技术， 2021， 42（2）： 327-334.
	TANG L， LI P， ZHOU L X， et al. Theoretical modeling of liquid sheet shape formed by oblique jet impinging onto wall［J］. Journal of Propulsion Technology， 2021， 42（2）： 327-334 （in Chinese）.
19	KATE R P， DAS P K， CHAKRABORTY S. Effects of jet obliquity on hydraulic jumps formed by impinging circular liquid jets on a moving horizontal plate［J］. Journal of Fluids Engineering， 2009， 131（3）： 034502.
20	MERTENS K， PUTKARADZE V， VOROBIEFF P. Morphology of a stream flowing down an inclined plane. Part 1. Braiding［J］. Journal of Fluid Mechanics， 2005， 531： 49-58.
21	WILSON D I， LE B L， DAO H D A， et al. Surface flow and drainage films created by horizontal impinging liquid jets［J］. Chemical Engineering Science， 2012， 68（1）： 449-460.
22	WANG R X， HUANG Y， FENG X， et al. Semi-empirical model for the engine liquid fuel sheet formed by the oblique jet impinging onto a plate［J］. Fuel， 2018， 233： 84-93.
23	FARD M， ASHGRIZ N， MOSTAGHIMI J. A numerical model for flow simulation in spray nozzles： AIAA-2004-1156［R］. Reston： AIAA， 2004.
24	KIBAR A. Experimental and numerical investigations of the impingement of an oblique liquid jet onto a superhydrophobic surface： Energy transformation［J］. Fluid Dynamics Research， 2016， 48（1）： 015501.
25	KIBAR A. Experimental and numerical investigation of liquid jet impingement on superhydrophobic and hydrophobic convex surfaces［J］. Fluid Dynamics Research， 2017， 49（1）： 015502.
26	KIBAR A. Experimental and numerical investigation on a liquid jet impinging on a vertical superhydrophobic surface： Spreading and reflection［J］. Progress in Computational Fluid Dynamics， 2018， 18（3）： 150-163.
27	SARCHAMI A， ASHGRIZ N， TRAN H. A spray model to predict droplet size distribution produced by wall impingement nozzle： AIAA-2008-3837［R］. Reston： AIAA， 2008.
28	GRADECK M， KOUACHI A， DANI A， et al. Experimental and numerical study of the hydraulic jump of an impinging jet on a moving surface［J］. Experimental Thermal and Fluid Science， 2006， 30（3）： 193-201.
29	CHO M J， THOMAS B G， LEE P J. Three-dimensional numerical study of impinging water jets in runout table cooling processes［J］. Metallurgical and Materials Transactions B， 2008， 39（4）： 593-602.
30	FUJIMOTO H， SUZUKI Y， HAMA T， et al. Flow characteristics of circular liquid jet impinging on a moving surface covered with a water film［J］. ISIJ International， 2011， 51（9）： 1497-1505.
31	赵林林，丁玉栋，朱恂，等. 不同壁面特性下液膜铺展性能数值模拟［J］. 原子能科学技术， 2017， 51（5）： 865-871.
	ZHAO L L， DING Y D， ZHU X， et al. Numerical simulation of liquid film spreading performance with different wall features［J］. Atomic Energy Science and Technology， 2017， 51（5）： 865-871 （in Chinese）.
32	COOKE J J， ARMSTRONG L M， LUO K H， et al. Adaptive mesh refinement of gas-liquid flow on an inclined plane［J］. Computers & Chemical Engineering， 2014， 60： 297-306.
33	邱添. 液体射流冲击平板数值模拟研究［D］. 天津：中国民航大学， 2020.
	QIU T. Liquid jet plate imping numerical simulation［D］. Tianjin： Civil Aviation University of China， 2020 （in Chinese）.
34	BRACKBILL J U， KOTHE D B， ZEMACH C. A continuum method for modeling surface tension［J］. Journal of Computational Physics， 1992， 100（2）： 335-354.

类别	液膜宽度/mm			液膜长度/mm
类别	y=6 mm	y=12 mm	y=20 mm	液膜长度/mm
误差/%	-20.80	-15.88	-17.64	-7.63
实验	8.06	9.19	8.16	33.44
仿真	6.38	7.73	6.72	30.89

[1]	BAO Jun, WANG Yu, NIU Qian, ZHU Xidong, CHENG Jianjie. Influencing parameters and film flow mechanism of spray droplet impacting liquid film [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021, 42(S1): 726360-726360.
[2]	TANG Liang, HU Jinhua, LIU Jiwu, LI Ping, ZHOU Lixin, YANG Baoe. Experimental study on oblique jet wall impingement and geometrical parameter modeling of liquid film [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(12): 124061-124061.
[3]	XUE Shuaijie, LIU Hongjun, HONG Liu, CHEN Pengfei. Test on self-excited oscillation characteristics of an open-end swirl injector with thick liquid film [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(9): 122189-122198.
[4]	XUE Shuaijie, LIU Hongjun, HONG Liu, CHEN Pengfei. Experimental on dynamic characteristics of an open-end swirl injector with thick liquid film [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2018, 39(12): 122534-122534.
[5]	ZHANG Guoyuan, ZHAO Weigang, YAN Xiutian, CHEN Guoding, CHEN Yao. Principle and Simulation for Real-time Monitoring of the Non-contact Face Seal Based on POD Model [J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2012, 33(2): 354-361.

Numerical simulation on spreading of oblique jet impinging onto a wall

RichHTML

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

Figures/Tables 16

References 34

Related Articles 5

Recommended Articles

Metrics

Comments