自动消除主动磁悬浮轴承系统保护间隙机构的运动学分析
收稿日期: 2014-07-22
修回日期: 2014-10-14
网络出版日期: 2014-10-29
基金资助
国家自然科学基金 (51205186)
Kinematic analysis of auto-eliminating protective clearance device for active magnetic bearing systems
Received date: 2014-07-22
Revised date: 2014-10-14
Online published: 2014-10-29
Supported by
National Natural Science Foundation of China (51205186)
提出了一种可以在转子跌落后自动消除磁悬浮轴承系统中保护间隙的机构并介绍了其结构和工作原理。从运动学角度出发,分析了自动消除保护间隙轴承机构的自由度;对比了两种不同布局的机构的径向尺寸、支座摆动中心到连杆中销钉中心之间距离、连杆中销钉与销孔之间的间隙大小等主要参数对机构中支座的最大摆动角度的影响;设计并加工了相应的实物模型对理论结果进行了试验验证。研究结果表明,在相同的结构参数下,相比于支座摆动中心分布于连杆外侧的机构,采用支座摆动中心分布于连杆内侧机构中的支座能够获得更大的摆动角度。根据研究得到的结果给出了自动消除间隙保护轴承机构主要结构参数的设计准则,为自动消除间隙机构作为磁悬浮轴承系统保护轴承的设计和应用奠定了一定的基础。
俞成涛 , 徐龙祥 , 金超武 . 自动消除主动磁悬浮轴承系统保护间隙机构的运动学分析[J]. 航空学报, 2015 , 36(7) : 2485 -2496 . DOI: 10.7527/S1000-6893.2014.0289
An auto-eliminating clearance auxiliary bearing device which can automatically eliminate the protective clearance in active magnetic bearing system after rotor dropping is presented. Firstly, its mechanical structure and working principles are introduced. Secondly, the device's degree of freedom is kinematically analyzed. Moreover, for two different structures of devices, the influences of the devices' radial dimension, the distance between the swing center of support and the center of the pin hole in link rod, the size of the clearance between the pin and pin hole in link rod on the maximum swing angle of the supports in these two devices are compared. Finally, the maximum swing angles of those supports in each situation are experimentally verified. The results show that compared with the device with the structure that the swing centers of supports are located at the outer side of the link rod, supports in the device in which the swing centers are placed in the inner side of the link rod could swing to a greater angle. According to these results, the design criterion of the main structure parameters of auto-eliminating clearance auxiliary bearing is given. The results provide a theoretical basis for the design and use of this auxiliary bearing in active magnetic bearing systems.
[1] Gerhard S, Maslen E H. Magnetic bearings theory, design, and application to rotating machinery[M]. New York: Springer, 2009: 1-26.
[2] Yu L. Controllable magnetic suspension rotor system [M]. Beijing: Science Press, 2003: 1-7 (in Chinese). 虞烈. 可控磁悬浮转子系统[M]. 北京: 科学出版社, 2003: 1-7.
[3] Antkowiak B M, Nelson F C. Rotor dynamic modeling of an active magnetic bearing gas turbine engine[C]// ASME Turbo Expo 1997. Orlando: American Society of Mechanical Engineers, 1997.
[4] Iannello V. Magnetic bearing systems for gas turbine engines[C]//Proceedings of MAG'95, 1995: 77-86.
[5] Storace A F, Sood D, Lyons J P, et al. Integration of magnetic bearings in the design of advanced gas turbine engines[J]. Journal of Engineering for Gas Turbines and Power, 1995, 117(4): 655-665.
[6] Meeks C, Mcmullen P, Hibner D, et al. Lightweight magnetic bearing system for aircraft gas turbine engines[C]//Proceeding of the Fourth International Symposium on Magnetic Bearings, 1994: 429-434.
[7] Ohsawa M, Yoshida K, Ninomiya H, et al. High-temperature blower for molten carbonate fuel cell supported by magnetic bearings[C]//Proceeding of the Sixth International Symposium on Magnetic Bearings, 1998: 32-41.
[8] Xu L X, Wang L T, Schweitzer G. Development of magnetic bearings for high temperature suspensions[C]//Proceedings of the Seventh International Symposium on Magnetic Bearings, 2000: 117-122.
[9] Xu L X, Zhou B. The current situation and development trend for more-electric gas turbine engines[J]. Journal of Aerospace Power, 2003, 18(1): 51-59 (in Chinese). 徐龙祥, 周波. 磁浮多电航空发动机的研究现状及关键技术[J]. 航空动力学报, 2003, 18(1): 51-59.
[10] Jin C W, Xu L X, Zhu Y L. Research on displacement sensor of high temperature active magnetic bearing[J]. Acta Aeronautica et Astronautica Sinica, 2014, 35(1): 230-239 (in Chinese). 金超武, 徐龙祥, 朱益利. 高温磁悬浮轴承用位移传感器的研究[J]. 航空学报, 2014, 35(1): 230-239.
[11] Ishii T, Kirk R G. Transient response technique applied to active magnetic bearing machinery during rotor drop[J]. Journal of Vibration and Acoustics, 1996, 118(2): 154-163.
[12] Keogh P S, Cole M O T. Rotor vibration with auxiliary bearing contact in magnetic bearing systems Part 1: Synchronous dynamics[J]. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2003, 217(4): 377-392.
[13] Ohura Y, Ueda K, Sugita S. Performance of touchdown bearings for turbo molecular pumps[C]//Proceeding of the Eighth International Symposium on Magnetic Bearings, 2002: 515-520.
[14] Zeng S. Modelling and experimental study of the transient response of an active magnetic bearing rotor during rotor drop on back-up bearings[J]. Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, 2003, 217(6): 505-517.
[15] Cuesta E N, Montbrun N I, Rastelli V, et al. Simple model for a magnetic bearing system operating on the auxiliary bearing[C]// ASME Turbo Expo 2005. Nevada: International Gas Turbine Institute, 2005: 891-898.
[16] Sun G. Rotor drop and following thermal growth simulations using detailed auxiliary bearing and damper models[J]. Journal of Sound and Vibration, 2006, 289(1-2): 334-359.
[17] Schweitzer G. Safety and reliability aspects for active magnetic bearing applications—a survey[J]. Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, 2005, 219(6): 383-392.
[18] Clark D J, Jansen M J, Montagure G T. An overview of magnetic bearing technology for gas turbine engines, NASA/TM-2004-213177[R]. Washington, D.C.: NASA,2004.
[19] Chen H M, Walton J, Heshmat H. Zero clearance auxiliary bearings for magnetic bearing systems[C]//ASME Turbo Expo 1997. Orlando: American Society of Mechanical Engineers, 1997.
[20] Salehi M, Heshmat H. On the dynamic and thermal performance of a zero clearance auxiliary bearing (zcab) for a magnetic bearing system[J]. Tribology Transaction, 2000, 43(3): 435-440.
[21] Yu L, Geng H P, Qi S M, et al. Compliant foil bearings used as emergence bearings[C]//Proceedings of the Ninth International Symposium on Magnetic Bearings, 2004: 129-136.
[22] Swanson E E, Heshmat H, Walton J F. Performance of a foil-magnetic hybrid bearing[J]. Journal of Engineering for Gas Turbines and Power, 2002, 124(2): 375-382.
[23] Dellacorte C, Valco M J. Load capacity estimation of foil air journal bearings for oil-free turbomachinery applications, NASA/TM-2000-209782[R]. Washington, D.C.: NASA, 2000.
[24] Wu L S, Chen H, Shi T L, et al. Design of a new-style assistant bearing of magnetic bearing[J]. Machinery Design and Manufacture, 2010(3): 32-34 (in Chinese). 伍良生, 陈浩, 史铁林, 等. 一种新型的电磁轴承系统辅助轴承的设计[J]. 机械设计及与制造, 2010(3): 32-34.
/
| 〈 |
|
〉 |
CJA