模具约束条件对H96黄铜双脊矩形管E弯截面变形的影响
收稿日期: 2014-04-28
修回日期: 2014-06-03
网络出版日期: 2014-06-13
基金资助
国家自然科学基金 (51375392);高等学校博士学科点专项科研基金博导类课题(20116102110012);陕西省自然科学基础研究计划 (2013JZ016)
Influence of die constraint condition on cross-sectional deformation of H96 brass double-ridged rectangular tube in E-typed rotary draw bending process
Received date: 2014-04-28
Revised date: 2014-06-03
Online published: 2014-06-13
Supported by
National Natural Science Foundation of China (51375392); Specialized Research Fund for Doctoral Program of Higher Education (20116102110012); Natural Science Basis Research Plan in Shaanxi Province of China (2013JZ016)
双脊矩形管的绕弯成形受内外侧模具的共同约束,不同模具约束下管坯的受力不同,使得其截面变形情况也不相同,而截面变形严重地影响弯管件的成形质量和使用性能。因此,基于ABAQUS有限元平台建立了双脊矩形管E弯成形三维有限元模型,并通过实验验证了模型的可靠性。采用所建模型,研究了内外侧模具约束条件对双脊矩形管E弯截面变形的影响规律,发现当只有内腹板脊槽受约束时,内腹板脊槽的内缩变形可得到较好的控制,而其他部位的变形则有增大的趋势;当只有外腹板脊槽受约束时,内腹板脊槽宽度变形基本不发生变化,而其他部位的变形则有减小的趋势;当内外腹板脊槽均受约束时,可较好地控制双脊矩形管E弯过程中的截面变形。芯头个数对整管截面高度、宽度、外腹板脊槽宽度与两脊槽底部的间距的变形影响较大,但对内腹板脊槽宽度的变形影响不显著。
刘春梅 , 刘郁丽 , 任家海 , 杨合 . 模具约束条件对H96黄铜双脊矩形管E弯截面变形的影响[J]. 航空学报, 2015 , 36(4) : 1320 -1329 . DOI: 10.7527/S1000-6893.2014.0113
The rotary draw bending process of the double-ridged rectangular tube is a complex nonlinear physical process with the internal and external die constraints. The stresses of the tubes under different die constraint conditions are different, which changes the situation of the cross-sectional deformation. And the deformation affects the quality and usability of double-ridged rectangular bending tube seriously. Then, based on the FE platform of ABAQUS/Explicit, the 3D-FE model is established for E-typed rotary draw bending of H96 brass double-ridged rectangular tube and validated by the experiment. Using the model, the influence of the internal and external die constraint conditions on cross-sectional deformation of the double-ridged rectangular tube in E-typed rotary draw bending process is researched. The results show that only when the inner ridge groove is constrained, the inner ridge groove shrinkage deformation can be better controlled, but other deformation is larger. Only when the outer ridge groove is constrained, the inner ridge groove width deformation does not change basically, but other deformation is smaller. When the inner and outer ridge grooves are both constrained, the cross-sectional deformation can be controlled effectively. The number of cores has more significant effect on the cross-sectional deformation, including the height and width of the global tube, the outer ridge groove width and the two ridge grooves spacing deformation, but has no significant impact on the width deformation of inner ridge groove.
[1] Wang T, Chen X Q. Study of characteristic impedance of double ridge waveguide using the finite element method [J]. Electronics Quality, 2009(9): 4-5 (in Chinese). 王涛, 陈小强. 矩形双脊波导特性阻抗的有限元分析[J]. 电子质量, 2009(9): 4-5.
[2] Zhang S P, Gao X H, Dong X H. Research on processing high precision rectangular bend cooper waveguide tube[J]. Netshape Forming Engineering, 2010, 2(1): 66-68 (in Chinese). 张胜平, 高小红, 董新汉. 高精度矩形弯铜导管加工研究[J]. 精密成形工程, 2010, 2(1): 66-68.
[3] Wang Y S. The double ridge waveguide process [J]. Electronics Process Technology, 1994(6): 18-19 (in Chinese). 王雨松. 双脊波导加工[J]. 电子工艺技术, 1994(6): 18-19.
[4] Ruan Z G. The bending and twisting process of the 24JS-3500 double ridge waveguide tube [J]. Technology and Economy Information of Shipbuilding Industry, 2000(7): 41-44 (in Chinese). 阮志刚. 24JS-3500双脊波导管弯扭成型工艺[J]. 船舶工业技术经济信息, 2000(7): 41-44.
[5] Xiao Y H, Liu Y L, Yang H, et al. Optimization of processing parameters for double-ridged rectangular tube rotary draw bending based on grey relational analysis[J]. The International Journal of Advanced Manufacturing Technology, 2014, 70(9-12): 2003-2011.
[6] Xiao Y H, Liu Y L, Yang H. Prediction of forming limit based on cross-sectional distortion for rotary draw bending of H96 brass double-ridged rectangular tube[J]. The International Journal of Advanced Manufacturing Technology, 2014, 71(5-8): 1445-1454.
[7] Liu C M, Liu Y L, Shen H W, et al. Characteristics of cross section deformation of double-ridge rectangular tube of H96 brass in rotary draw bending process[J]. Journal of Aeronautical Materials, 2013, 33(6): 13-19 (in Chinese). 刘春梅, 刘郁丽, 沈化文, 等. H96黄铜双脊矩形波导管绕弯截面变形特征研究[J]. 航空材料学报, 2013, 33(6): 13-19.
[8] Welo T, Paulsen F, Brobak T J. The behaviour of thin-wall aluminium alloy profile in rotary draw bending—a comparison between numerical and experience results[J]. Journal of Materials Processing Technology, 1994, 45(1-4): 173-180.
[9] Paulsen F, Welo T. Application of numerical simulation in the bending of aluminium-alloy profiles[J]. Journal of Materials Processing Technology, 1996, 58: 274-285.
[10] Utsumi N, Sakaki S. Countermeasures against undesirable phenomena in the draw-bending process for extruded square tubes[J]. Journal of Material Process Techhnology, 2002, 123(2): 264-269.
[11] Miller J E, Kyriakides S, Bastard A H. On bend-stretch forming of aluminum extruded tubes—I: experiments[J]. International Journal of Mechanical Sciences, 2001, 43(5): 1283-1317.
[12] Jia L L, Gao J Z. Bending technology of hollow alumal-shape in use for automobile frame[J]. Metal Forming Technology, 2000, 18(6): 34-35 (in Chinese). 贾俐俐, 高锦张. 汽车门框空腹铝型材弯曲工艺[J]. 金属成形工艺, 2000, 18(6): 34-35.
[13] Qi H Y, Liu Y L, Yang H. Influence of mandrel parameters on cross-section deformation of 3A21 rectangular tube in rotary-draw bending process[J]. Materials Science and Technology, 2012, 20(6): 97-102 (in Chinese). 齐海雁, 刘郁丽, 杨合. 芯模参数对3A21矩形管绕弯截面变形的研究[J]. 材料科学与工艺, 2012, 20(6): 97-102.
[14] Zhao G Y, Liu Y L, Yang H, et al. Cross-sectional distortion behaviors of thin-walled rectangular tube in rotary-draw bending process[J]. Transactions of Nonferrous Metals Society of China, 2010, 20(3): 484-489.
[15] Zhu Y X, Liu Y L, Yang H. Sensitivity of springback and section deformation to process parameters in rotary draw bending of thin-walled rectangular H96 brass tube[J]. Transactions of Nonferrous Metals Society of China, 2012, 22(9): 2233-2240.
/
| 〈 |
|
〉 |
CJA