GH4169DA磨削表面变质层软化机理
收稿日期: 2013-06-27
修回日期: 2013-09-03
网络出版日期: 2013-09-04
基金资助
国家自然科学基金(51175430)
Softening Mechanism of Grinding Surface Metamorphic Layer of GH4169DA
Received date: 2013-06-27
Revised date: 2013-09-03
Online published: 2013-09-04
Supported by
National Natural Science Foundation of China (51175430)
为了深入研究高温合金GH4169DA磨削表面变质层软化机理,分别采用光学显微镜、显微维氏硬度计和透射电子显微镜(TEM)分析了其微观组织、显微硬度和γ"相密度。试验结果表明:GH4169DA磨削表面及亚表面发生了明显软化和局部塑性变形。在试验参数范围内,软化深度约为30~100 μm,而变形层的深度只有约4 μm。从基体到磨削表面,γ"相密度由约2.27×103个/μm2逐渐降低,至距磨削表面约2.2 μm以内γ"相完全消失。该变化规律与显微硬度变化规律一致,最大影响深度也基本相同。分析指出,GH4169DA磨削表面软化的根本原因是在磨削过程中热的作用下,主要强化相γ"密度降低,强化效果减弱。
杜随更 , 姜哲 , 张定华 , 巨江涛 , 李娜 . GH4169DA磨削表面变质层软化机理[J]. 航空学报, 2014 , 35(5) : 1446 -1451 . DOI: 10.7527/S1000-6893.2013.0378
In order to study the softening mechanism of the grinding surface metamorphic layer of superalloy GH4169DA, the microstructure, Vickers hardness and γ" phase density of the metamorphic layer are investigated by the metallographic microscope, micro Vickers and transmission electron microscopy (TEM). The results show that there is softening and local plastic deformation on the grinding surface and sub-surface of GH4169DA. In the range of the test parameters, the depth of the softened layer is approximately 30 μm to 100 μm, and the depth of the deformed layer is only about 4 μm. From the matrix to the grinding surface, the number of γ" phase per square micron decreases gradually from about 2.27×103 to zero, and the γ" phase disappears completely within 2.2 μm depth of the grinding surface. The causes of the γ" phase density vari-ation are basically the same as the variation of microhardness. The softening mechanism of the grinding surface of GH4169DA is that the main strengthening phase γ" density decreases and its enhancement effect weakens under the action of the heat generated by the grinding process.
[1] Hong S J, Chen W P, Wang T W. A diffraction study of the γ" phase in INCONEL 718 superalloy[J]. Metallurgical and Materials Transactions A, 2001, 32(8):1887-1901.
[2] Dehmas M, Lacaze J, Niang A, et al. TEM study of high-temperature precipitation of delta phase in Inconel 718[J]. Advances in Materials Science and Engineering, 2011, 2011: 1-9.
[3] Chang S H. In situ TEM observation of γ', γ" and δ precipitations on Inconel 718 superalloy through HIP treatment[J]. Journal of Alloys and Compounds, 2009,486 (1-2): 716-721.
[4] Zhang H Y, Zhang S H, Cheng M, et al. Deformation characteristics of δ phase in the delta-processed Inconel 718 alloy[J]. Materials Characterization, 2010, 61(1):49-53.
[5] Sharman A R C, Hughes J I, Ridgway K. An analysis of the residual stresses generated in Inconel 718TM when turning[J]. Journal of Materials Processing Technology, 2006, 173(3): 359-367.
[6] Arunachalam R M, Mannan M A, Spowage A C. Resid-ual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools[J]. International Journal of Machine Tools and Manufacture, 2004, 44(9): 879-887.
[7] Thakur D G, Ramamoorthy B, Vijayaraghavan L. Study on the machinability characteristics of superalloy Inconel 718 during high speed turning[J]. Materials and Design, 2009, 30(5): 1718-1725.
[8] Yu H F. The mechanism grinding burn of nickel base superalloy[J]. Journal of Changzhou Industrial Technology College: Natural Science Edition, 1996, 9(2):55-57. (in Chinese) 于洪方. 镍基高温合金磨削烧伤机理[J]. 常州工业技术学院学报: 自然科学版, 1996, 9(2): 55-57.
[9] Devillez A, Le Coz S, Dominiak S, et al. Dry machining of Inconel 718, workpiece surface integrity[J]. Journal of Materials Processing Technology, 2011, 21(10): 1590-1598.
[10] Du S G, Wang Z B, Lv C, et al. Study on high-speed milling surface microstructure of superalloys[J]. Acta Aeronautica et Astronautica Sinica, 2011, 32(6): 1156-1163. (in Chinese) 杜随更, 汪志斌, 吕超, 等. 高温合金高速铣削表面形貌及组织研究[J]. 航空学报, 2011, 32(6): 1156-1163.
[11] sterle W, Li P X. Mechanical and thermal response of a nickel-base superalloy upon grinding with high removal rates[J]. Materials Science and Engineering, 1997, 238(12): 357-366.
[12] Chen M, Li X T, Sun F H, et al. Studies on the grinding characteristics of directionally solidified nickel-based superalloy[J]. Journal of Materials Processing Technology, 2001, 116(2-3): 165-169.
[13] Ren J X, Kang R K, Shi X K, et al. Grinding of difficult-to-cut materials[M]. Beijing: National Defence Industry Press, 1999: 251-252. (in Chinese) 任敬心, 康仁科, 史兴宽, 等. 难加工材料的磨削[M].北京:国防工业出版社, 1999: 251-252.
[14] Xu P. High speed grinding of Nickel superalloy using CBN wheels. Nanjing: College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, 2010. (in Chinese) 徐鹏. CBN 砂轮高速磨削镍基高温合金. 南京:南京航空航天大学机电学院, 2010.
[15] Coelho R T, Silva L R, Braghini A, et al. Some effects of cutting edge preparation and geometric modifications when turning INCONEL 718TM at high cutting speeds[J]. Journal of Materials Processing Technology, 2004, 148(1):147-153.
[16] Sharmana A R C, Hughesa J I, Ridgwaya K. Workpiece surface integrity and tool life issues when turning Inconel 718TM nickel based superalloy[J]. Machining Science and Technology, 2004, 8(3): 399-414.
[17] Guo J T. Materials science and engineering superalloy (Volume 1)[M]. Beijing: Science Press, 2008: 292. (in Chinese) 郭建亭. 高温合金材料学(上册)[M]. 北京: 科学出版社, 2008: 292.
[18] China Aeronautical Materials Handbook Editorial Board. China aeronautical materials handbook (Volume 2)[M]. 2nd ed. Beijing: China Standard Publishing House, 2001: 328. (in Chinese) 中国航空材料手册编辑委员会. 中国航空材料手册(第二卷)[M]. 2版. 北京: 中国标准出版社, 2001: 328.
/
〈 |
|
〉 |