ACTA AERONAUTICAET ASTRONAUTICA SINICA >
Particle deformation behavior and pores distribution of cold sprayed Ti coatings
Received date: 2023-07-12
Revised date: 2023-08-14
Accepted date: 2023-09-11
Online published: 2023-09-27
Supported by
Cooperation Project （NSFC-DFG） of the National Natural Science Foundation of China(52061135101)
In the deposition process of Cold Spraying （CS）， the bonding strength between particles is small， and defectsas pores and interparticle boundaries are common in the coatings. In order to study the formation mechanism of these defects， three kinds of Ti coatings with different particle sizes distributions were prepared at different airflow temperatures. According to the experimental parameters， the Coupled Euler-Lagrange （CEL） model of random multi-particle deposition was established， and the deformation of particles after deposition and the pores distribution law inside the coatings were calculated. The results showed that the numerical simulation and experimental results were in good agreement. The collision action causes the accumulation of particles to be directional， and with the increase of velocities， the deformation of particles increases， and the inner particles are more affected by the velocities than the outer particles. Under the same parameters， the deposits with large particles have larger pores and higher porosities. At low velocities， the pores inside the coatings communicate with each other to form pore clusters， and as the velocities increase， the pore sizes decrease and the porosities decrease.
Key words： cold spraying; Ti coating; CEL model; particle deformation; pores distribution
Chouting ZHOU , Yu’e MA , Zexuan YANG , Wenya LI , Chunjie HUANG , Lei LIU . Particle deformation behavior and pores distribution of cold sprayed Ti coatings[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2024 , 45(12) : 429316 -429316 . DOI: 10.7527/S1000-6893.2023.29316
| 1 | YIN S， CAVALIERE P， ALDWELL B， et al. Cold spray additive manufacturing and repair： Fundamentals and applications［J］. Additive Manufacturing， 2018， 21： 628-650. |
| 2 | ASSADI H， KREYE H， G?RTNER F， et al. Cold spraying—A materials perspective［J］. Acta Materialia， 2016， 116： 382-407. |
| 3 | 吴洪键， 李文波， 邓春明， 等. 冷喷涂增材制造关键技术［J］. 中国表面工程， 2020， 33（4）： 1-15. |
| WU H J， LI W B， DENG C M， et al. Key techniques of cold spray additive manufacturing［J］. China Surface Engineering， 2020， 33（4）： 1-15 （in Chinese）. | |
| 4 | YANG K， LI W Y， YANG X W， et al. Effect of heat treatment on the inherent anisotropy of cold sprayed copper deposits［J］. Surface and Coatings Technology， 2018， 350： 519-530. |
| 5 | SAMPLE C M， CHAMPAGNE V K， NARDI A T， et al. Factors governing static properties and fatigue， fatigue crack growth， and fracture mechanisms in cold spray alloys and coatings/repairs： A review［J］. Additive Manufacturing， 2020， 36： 101371. |
| 6 | GUO D L， WANG Y， FERNANDEZ R， et al. Cold spray for production of in situ nanocrystalline MCrAlY coatings—Part I： Process analysis and microstructure characterization［J］. Surface and Coatings Technology， 2021， 409： 126854. |
| 7 | 管宇， 陈亮， 曹奇凯. 基于增量考核的飞机延寿方法与应用［J］. 航空学报， 2021， 42（8）： 525782. |
| GUAN Y， CHEN L， CAO Q K. Aircraft life extension based on incremental assessment： Method and application［J］. Acta Aeronautica et Astronautica Sinica， 2021， 42（8）： 525782 （in Chinese）. | |
| 8 | LI W Y， CAO CC， YIN S. Solid-state cold spraying of Ti and its alloys： A literature review［J］. Progress in Materials Science， 2020， 110： 100633. |
| 9 | YU T Y， CHEN M J， WU Z R. Experimental and numerical study of deposition mechanisms for cold spray additive manufacturing process［J］. Chinese Journal of Aeronautics， 2022， 35（2）： 276-290. |
| 10 | BAE G， KUMAR S， YOON S， et al. Bonding features and associated mechanisms in kinetic sprayed titanium coatings［J］. Acta Materialia， 2009， 57（19）： 5654-5666. |
| 11 | YIN S， SUO X K， SU J Q， et al. Effects of substrate hardness and spray angle on the deposition behavior of cold-sprayed Ti particles［J］. Journal of Thermal Spray Technology， 2014， 23（1）： 76-83. |
| 12 | ZAHIRI S H， MAYO， JAHEDI M. Characterization of cold spray titanium deposits by X-ray microscopy and microtomography［J］. Microscopy and Microanalysis， 2008， 14（3）： 260-266. |
| 13 | CAVALIERE P， SILVELLO A. Processing conditions affecting residual stresses and fatigue properties of cold spray deposits［J］. The International Journal of Advanced Manufacturing Technology， 2015， 81（9）： 1857-1862. |
| 14 | WONG W， IRISSOU E， VO P， et al. Cold spray forming of inconel 718［J］. Journal of Thermal Spray Technology， 2013， 22（2）： 413-421. |
| 15 | SANSOUCY E， KIM G E， MORAN A L， et al. Mechanical characteristics of Al-Co-Ce coatings produced by the cold spray process［J］. Journal of Thermal Spray Technology， 2007， 16（5）： 651-660. |
| 16 | BHATTIPROLU V S， JOHNSON K W， OZDEMIR O C， et al. Influence of feedstock powder and cold spray processing parameters on microstructure and mechanical properties of Ti-6Al-4V cold spray depositions［J］. Surface and Coatings Technology， 2018， 335： 1-12. |
| 17 | CHEN C Y， XIE Y C， YAN X C， et al. Effect of hot isostatic pressing （HIP） on microstructure and mechanical properties of Ti6Al4V alloy fabricated by cold spray additive manufacturing［J］. Additive Manufacturing， 2019， 27： 595-605. |
| 18 | REN Y Q， KING P C， YANG Y S， et al. Characterization of heat treatment-induced pore structure changes in cold-sprayed titanium［J］. Materials Characterization， 2017， 132： 69-75. |
| 19 | AHMED F， BERNDT CHRISTOPHER C， REHAN A. Numerical modelling of particle impact and residual stresses in cold sprayed coatings： A review［J］. Surface and Coatings Technology， 2021， 409： 126835. |
| 20 | YIN S， WANG X F， XU B P， et al. Examination on the calculation method for modeling the multi-particle impact process in cold spraying［J］. Journal of Thermal Spray Technology， 2010， 19（5）： 1032-1041. |
| 21 | SCHMIDT T， ASSADI H， G?RTNER F， et al. From particle acceleration to impact and bonding in cold spraying［J］. Journal of Thermal Spray Technology， 2009， 18（5）： 794-808. |
| 22 | SONG X， NG K L， CHEA J M K， et al. Coupled Eulerian-Lagrangian （CEL） simulation of multiple particle impact during metal cold spray process for coating porosity prediction［J］. Surface and Coatings Technology， 2020， 385： 125433. |
| 23 | WEILLER S， DELLORO F. A numerical study of pore formation mechanisms in aluminium cold spray coatings［J］. Additive Manufacturing， 2022， 60： 103193. |
| 24 | JOHNSON G R， COOK W H. Fracture characteristics of three metals subjected to various strains， strain rates， temperatures and pressures［J］. Engineering Fracture Mechanics， 1985， 21（1）： 31-48. |
| 25 | KUMAR S， BAE G， LEE C. Influence of substrate roughness on bonding mechanism in cold spray［J］. Surface and Coatings Technology， 2016， 304： 592-605. |
| 26 | GRUJICIC M， ZHAO C L， DEROSSET W S， et al. Adiabatic shear instability based mechanism for particles/substrate bonding in the cold-gas dynamic-spray process［J］. Materials & Design， 2004， 25（8）： 681-688. |
| 27 | SCHMIDT T， G?RTNER F， ASSADI H， et al. Development of a generalized parameter window for cold spray deposition［J］. Acta Materialia， 2006， 54（3）： 729-742. |
/
| 〈 |
|
〉 |
CJA