A three-factor and five-level orthogonal table is designed using the Taguchi method for the sister hole structure, with the compound angle, the inclination angle and the blowing ratio as factors and the average wall film cooling effectiveness as the evaluation index. The flow characteristics and the cooling effectiveness distribution under different conditions are analyzed with numerical calculations. Results show that the film cooling effectiveness of the sister holes is 165%-412.5% of that of conventional cylindrical holes at a high blowing ratio, and the film cooling effectiveness of the sister holes with a 10° compound angle is higher than that of the sister holes with a -10° compound angle. Parameterized results reveal that the hole structure with a blowing ratio of 0.5, a compound angle of 10° and an inclination angle of 35° exhibits the best cooling performance.
WANG Jin
,
SUN Jie
,
ZHAO Zhanming
,
ZHANG Bo
,
REN Xiaodong
,
XIE Gongnan
. Research on film cooling performance of sister hole based on structural parameter analysis[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2021
, 42(7)
: 124775
-124775
.
DOI: 10.7527/S1000-6893.2020.24775
[1] ZHANG J Z, ZHANG S C, WANG C H, et al. Recent advances in film cooling enhancement:A review[J]. Chinese Journal of Aeronautics, 2020, 33(4):1119-1136.
[2] ACHARYA S. Film cooling simulation and control[J]. Heat Transfer Research, 2010, 41(6):601-626.
[3] 丁阳, 常海萍, 杜治能. 多排反向射流角气膜冷却特性研究[J]. 航空学报, 2013, 34(11):2472-2481. DING Y, CHANG H P, DU Z N. Investigation on characteristics of multiple rows of opposite lateral ejection angle film cooling[J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(11):2472-2481(in Chinese).
[4] YANG C F, ZHANG J Z. Experimental investigation on film cooling characteristics from a row of holes with ridge-shaped tabs[J]. Experimental Thermal and Fluid Science, 2012, 37:113-120.
[5] ZHANG Y M, WEN Z X, PEI H Q, et al. Equivalent model of close-packed film cooling holes in nickel-based single crystal cooled blade based on crystallographic theory[J]. Chinese Journal of Aeronautics, 2019, 32(4):839-850.
[6] ZHANG S C, ZHANG J Z, TAN X M. Improvement on shaped-hole film cooling effectiveness by integrating upstream sand-dune-shaped ramps[J]. Chinese Journal of Aeronautics, 2021, 34(4):42-55.
[7] WU H, CHENG H C, LI Y L, et al. Effects of side hole position and blowing ratio on sister hole film cooling performance in a flat plate[J]. Applied Thermal Engineering, 2016, 93:718-730.
[8] HOU R, WEN F B, WANG S T, et al. Large eddy simulation of the trenched film cooling hole with different compound angles and coolant inflow orientation effects[J]. Applied Thermal Engineering, 2019, 163:114397.
[9] YAO J X, SU P F, HE J H, et al. Experimental and numerical investigations on double-jet film-cooling with different mainstream incidence angles[J]. Applied Thermal Engineering, 2020, 166:114737.
[10] FAWZY H, ZHENG Q, JIANG Y T, et al. Study of utilizing double lateral sub holes at different spanwise angles on blade film cooling effectiveness[J]. International Communications in Heat and Mass Transfer, 2020, 117:104728.
[11] ABDELMOHIMEN M A H, MOHIUDDIN A. Experimental investigation of film cooling from compound angle holes supplemented by secondary holes[J]. International Journal of Heat and Mass Transfer, 2019, 144:118678.
[12] ZHOU J F, WANG X J, LI J, et al. Effects of diameter ratio and inclination angle on flow and heat transfer characteristics of sister holes film cooling[J]. International Communications in Heat and Mass Transfer, 2020, 110:104426.
[13] TIAN K, WANG J, LIU C, et al. Effect of combined hole configuration on film cooling with and without mist injection[J]. Thermal Science, 2018, 22(5):1923-1931.
[14] CAO N, LI X, WU Z Y, et al. Effect of film hole geometry and blowing ratio on film cooling performance[J]. Applied Thermal Engineering, 2020, 165:114578.
[15] TIAN K, WANG J, LIU C, et al. Effect of blockage configuration on film cooling with and without mist injection[J]. Energy, 2018, 153:661-670.
[16] 赵占明, 翟郑佳, 刘超, 等. 分支孔结构对气膜冷却效率的影响研究[J]. 兵器装备工程学报, 2020, 41(2):216-220. ZHAO Z M, ZHAI Z J, LIU C, et al. Impact research of branch hole structure on film cooling effectiveness[J]. Journal of Ordnance Equipment Engineering, 2020, 41(2):216-220(in Chinese).
[17] SEO H J, KANG Y J, LEE H C, et al. Optimization of the configuration of the laidback fan-shaped film cooling hole with a lateral expansion angle of 10 degrees[J]. Applied Thermal Engineering, 2019, 153:379-389.
[18] HUANG Y, ZHANG J Z, WANG C H. Multi-objective optimization of round-to-slot film cooling holes on a flat surface[J]. Aerospace Science and Technology, 2020, 100:105737.
[19] ZAMIRI A, YOU S J, CHUNG J T. Large eddy simulation in the optimization of laidback fan-shaped hole geometry to enhance film-cooling performance[J]. International Journal of Heat and Mass Transfer, 2020, 158:120014.
[20] MADRANE A, AN H C, LENG J Z, et al. Shape optimization of inclined hole for enhanced film-cooling performance using discrete adjoint method[J]. International Journal of Thermal Sciences, 2020, 158:106542.
[21] TAGUCHI G, PHADKE M S. Quality engineering through design optimization[M]//Quality Control, Robust Design, and the Taguchi Method. Boston:Springer, 1989:77-96.
[22] WANG J, LIU C, ZHAO Z M, et al. Effect and optimization of backward hole parameters on film cooling performance by Taguchi method[J]. Energy Conversion and Management, 2020, 214:112809.
[23] SINHA A K, BOGARD D G, CRAWFORD M E. Film-cooling effectiveness downstream of a single row of holes with variable density ratio[J]. Journal of Turbomachinery, 1991, 113(3):442-449.
CJA