同轴激光熔覆粉末的熔化行为表征与分析
收稿日期: 2023-02-28
修回日期: 2023-03-13
录用日期: 2023-05-18
网络出版日期: 2023-06-27
基金资助
国家自然科学基金(52065041);中国-乌克兰政府间科技交流项目;甘肃省教育厅“双一流”科研重点项目(GSSYLXM-03);甘肃省兰州理工大学红柳优青项目
Characterization and analysis of melting behavior of powder in coaxial laser cladding
Received date: 2023-02-28
Revised date: 2023-03-13
Accepted date: 2023-05-18
Online published: 2023-06-27
Supported by
National Natural Science Foundation of China(52065041);China-Ukraine Intergovernmental Science and Technology Exchange Project;Gansu Provincial Department of Education “Double First Class” Key Research Project(GSSYLXM-03);Gansu Province Lanzhou University of Technology Red Willow Excellent Youth Project
同轴送粉激光熔覆过程中激光热量在粉末与熔池中的作用与分配对成形质量有着重要影响。针对作用形式最为复杂且难以红外实时检测的粉末与激光的热交互作用展开研究，首先建立了高速摄像系统并对标记的单颗粉末同轴送入激光后的熔化过程进行了采集与分析，研究了粉末熔化过程中不同特征阶段的热物理行为并建立了数学模型；同时由于难以根据有效的温度数据对模型进行验证和优化，故采用高速摄像统计分析了不同特征阶段的持续时间，与模型的计算结果进行了对比分析；最后在模型优化的基础上仿真预测了粉末即将进入熔池的温度与状态，为进一步分析粉末与熔池的热交互作用提供理论依据。研究结果表明：单颗粉末进入熔池后存在“固态→固液两相态→液态”的转变，不同转变过程的持续时间及热物理行为的变化并不相同；据此建立的数学模型可以动态描述粉末同轴送入激光后不同熔化阶段的持续时间与温度特征，通过与高速摄像统计数据对比验证了模型的有效性与准确性；仿真预测了粉末即将进入熔池时的温度特征，并分析了不同激光功率对粉末即将进入熔池时状态的影响与作用。
朱明 , 张宗智 , 杨骞 , 石玗 , 樊丁 . 同轴激光熔覆粉末的熔化行为表征与分析[J]. 航空学报, 2023 , 44(24) : 428581 -428581 . DOI: 10.7527/S1000-6893.2023.28581
The action and distribution of laser heat in the powder and melt pool during coaxial powder feeding laser cladding has an important influence on the forming quality. This paper conducted research on the complex and challenging thermal interaction between powder and laser， particularly difficult to detect in real-time infrared analysis. Firstly， a high-speed camera system is established and the melting process of a single powder coaxially fed into the laser was collected and analyzed， and the thermophysical behavior of different characteristic stages of the powder melting process is studied and a mathematical model is established. Moreover， due to the difficulty in validating and optimizing the model based on valid temperature data， the duration of the different characteristic phases was statistically analyzed using high-speed cameras， and was compared with the calculated results of the model. Finally， based on the optimization of the model， the simulation predicted the temperature and state of the powder about to enter the melt pool， which provides a theoretical basis for further analysis of the thermal interaction between the powder and the melt pool. The results show that： there is a transition of “solid → solid-liquid two-phase state → liquid” after a single powder enters the melt pool， and the duration and thermophysical behavior of different transition processes are not the same； the mathematical model established by this can dynamically describe the duration and temperature characteristics of different melting stages after the powder is fed into the laser. The validity and accuracy of the model were verified by comparing with high-speed camera statistics. The simulation predicted the temperature characteristics of the powder when it was about to enter the melt pool， and analyzed the influence and effect of different laser powers on the state of the powder when it is about to enter the molten pool.
| 1 | GU D D， MEINERS W， WISSENBACH K， et al. Laser additive manufacturing of metallic components： materials， processes and mechanisms［J］. International Materials Reviews， 2013， 57（3）：133-164. |
| 2 | 张津超， 石世宏， 龚燕琪， 等. 激光熔覆技术研究进展［J］. 表面技术， 2020， 49（10）： 1-11. |
| ZHANG J C， SHI S H， GONG Y Q， et al. Research progress of laser cladding technology［J］. Surface Technology， 2020， 49（10）： 1-11 （in Chinese）. | |
| 3 | 杜学芸， 许金宝， 宋健. 激光熔覆再制造技术研究现状及发展趋势［J］. 金属加工（热加工）， 2020 （3）： 15-19. |
| DU X Y， XU J B， SONG J. Research status and development trend of laser cladding remanufacturing technology ［J］. MW Metal Forming， 2020 （3）： 15-19 （in Chinese）. | |
| 4 | 周建忠， 何文渊， 徐家乐， 等. 激光熔覆Al2O3/Fe901复合涂层的强化机制及耐磨性［J］. 光学学报， 2019， 39（5）： 219-227. |
| ZHOU J Z， HE W Y， XU J L， et al. Strengthening mechanism and wear resistance of Al2O3/Fe901 composite coating prepared by laser cladding［J］. Acta Optica Sinica， 2019， 39（5）： 219-227 （in Chinese）. | |
| 5 | 白杨， 王振华， 左娟娟， 等. 激光熔覆制备铁基复合涂层及其耐热耐蚀性能［J］. 中国激光， 2020， 47（10）： 38-44. |
| BAI Y， WANG Z H， ZUO J J， et al. Fe-Based composite coating prepared by laser cladding and its heat and corrosion resistance［J］. Chinese Journal of Lasers， 2020， 47（10）： 38-44 （in Chinese）. | |
| 6 | KATINAS C， THROOP T， SHIN YC， et al. Laser cladding of Stellite-6 with a coaxial nozzle via modeling and systematic experimental investigations［J］. The International Journal of Advanced Manufacturing Technology， 2021，113： 837–853. |
| 7 | ZHU S， CHEN W， DING L， et al. A mathematical model of laser cladding repair［J］. The International Journal of Advanced Manufacturing Technology， 2019，103： 3265-3278. |
| 8 | LI C， ZHANG D， YANG Y， et al. Research on sputtering behavior of three beams coaxial laser cladding powder based on the interaction of lasers and powder［J］. Journal of Laser Applications， 2021， 33（4）： 42020. |
| 9 | 崔雪， 张松， 张春华， 等. 高性能梯度功能材料激光增材制造研究现状及展望［J］. 材料工程， 2020， 48（9）： 13-23. |
| CUI X， ZHANG S， ZHANG C H， et al. Research status and prospect of laser additive manufacturing technology for high performance gradient functional materials［J］. Journal of Materials Engineering， 2020， 48（9）： 13-23 （in Chinese）. | |
| 10 | SHI B， LI T， GUO Z， et al. Selecting process parameters of crack-free Ni60A alloy coating prepared by coaxial laser cladding［J］. Optics and Laser Technology， 2022， 149： 107805. |
| 11 | HEIGEL J C， GOUGE M F， MICHALERIS P， et al. Selection of powder or wire feedstock material for the laser cladding of Inconel 625［J］. Journal of Materials Processing Technology， 2016， 231（12）： 357-365. |
| 12 | WIRTH F， WEGENER K. A physical modeling and predictive simulation of the laser cladding process［J］. Additive Manufacturing， 2018， 22： 307-319. |
| 13 | SCHOPPHOVEN T， GASSER A， WISSENBACH K， et al. Investigations on ultra-high-speed laser material deposition as alternative for hard chrome plating and thermal spraying［J］. Journal of Laser Applications，2016， 28（2）：022501. |
| 14 | IBARRA-MEDINA J， PINKERTON A J. Numerical investigation of powder heating in coaxial laser metal deposition［J］. Surface Engineering， 2013， 27（10）： 754-761. |
| 15 | TABERNERO I. Modelling of energy attenuation due to powder flow-laser beam interaction during laser cladding process［J］. Journal of Materials Processing Technology， 2012， 212（2）： 516-522. |
| 16 | GULYAEV I， KOVALEV O， PINAEV P A， et al. Optical diagnostics of radiation interaction with the powder stream laterally transported during laser cladding［J］. Optics and Lasers in Engineering， 2020， 126： 105877. |
| 17 | 杨义成， 黄瑞生， 方乃文， 等. 光粉交互对同轴送粉增材制造能量传输的影响［J］. 焊接学报， 2020， 41（6）： 19-23. |
| YANG Y C， HUANG R S， FANG N W， et al. Effect of the interaction between laser beam and powder particles on energy transmission in coaxial powder feeding additive manufacturing［J］. Transactions of the China Welding Institution， 2020， 41（6）： 19-23 （in Chinese）. | |
| 18 | TAN H， FANG Y， ZHONG C， et al. Investigation of heating behavior of laser beam on powder stream in directed energy deposition［J］. Surface and Coatings Technology， 2020， 397：126061. |
| 19 | 朱明， 王博， 颜步云， 等. 激光熔覆过程预置粉末熔化行为的动态检测与分析［J］. 中国激光， 2021， 48 （14）： 140201301-140201310. |
| ZHU M， WANG B， YAN B Y， et al. Dynamic detection and analysis of fore put powder melting behavior in diode laser cladding process［J］. Chinese Journal of Lasers 2021， 48 （14）： 140201301-140201310 （in Chinese）. | |
| 20 | ZHU M， YAN B Y， LI X B， et al. Process research on diode laser-TIG hybrid overlaying welding process［J］. Transactions on Intelligent Welding Manufacturing， 2019， 1：161-168. |
| 21 | 席明哲， 虞钢， 张永忠， 等. 同轴送粉激光成形中粉末与激光的相互作用［J］. 中国激光， 2005 （4）： 562-566. |
| XI M Z， YU G， ZHANG Y Z， et al. Interaction of the laser beam and the metal powder conveyed by coaxial powder feeder［J］. Chinese Journal of Lasers， 2005 （4）： 562-566 （in Chinese）. |
/
| 〈 |
|
〉 |
CJA