掩膜电解加工技术是一种用于阵列结构加工的高效电化学加工技术，被广泛应用于各类难加工材料的阵列群孔、群坑或群槽的加工制造。目前，掩膜电解加工中多采用侧面单向供给电解液的方式进行加工，该冲液方式简单易行，但由于加工区迎水面和背水面的流场差异，造成群孔结构的成形精度较差。为此，提出了周期性换向冲液技术，以改善加工区流场分布，进而提升群孔结构的成形精度。通过数值模拟仿真和实验研究，明确了最佳的换向冲液频率，研究结果表明换向冲液技术可以有效提升孔的成形精度。最终，采用周期性换向冲液技术完成了阵列群孔结构的加工，相较于单向冲液，孔的侧壁与轴线夹角差异率下降至1%以内，获得了较高的成形精度。
Through-mask electrochemical machining technology is a high-efficiency electrochemical machining technology for array structure processing, which is widely used in the processing and manufacturing of array group holes, group pits or group grooves of various difficult-to-process materials. At present, through-mask electrochemical machining mostly adopts the method of unidirectionally supplying electrolyte from the side. Although the flushing method is simple and easy to implement, due to the difference in the flow field between the front and back water surfaces of the processing area, the formation accuracy of the group hole structure is poor. For this reason, this paper proposes a periodic reversing fluid flushing technology to improve the flow field distribution in the processing area, thereby enhancing the forming accuracy of the group hole structure. Through numerical simulation and experimental analysis, the best reversing flushing frequency is determined, which proves that the reversing flushing technology can effectively improve the quality of group hole processing. Finally, an array group hole structure is processed by periodic reversing flushing technology. Compared with unidirectional flushing, the difference rate of the angle between the side wall and the axis of the hole is reduced to less than 1%, and a higher forming accuracy is obtained.
[1] SAMUEL M P, MISHRA A K, MISHRA R K. Additive manufacturing of Ti-6Al-4V aero engine parts:Qualification for reliability[J]. Journal of Failure Analysis and Prevention, 2018, 18(6):1-9.
[2] 王增强. 先进航空发动机关键制造技术[J]. 航空制造技术, 2015, 58(22):34-38. WANG Z Q. Research on key manufacturing technology of advanced aeroengine[J]. Aeronautical Manufacturing Technology, 2015, 58(22):34-38(in Chinese).
[3] SUN Y, LING S, ZHAO D, et al. Through-mask electrochemical micromachining of micro pillar arrays on aluminum[J]. Surface and Coatings Technology, 2020, 40:126277.
[4] CHEN X L,QU N S,LI H S, et al. Removal of islands from micro-dimple arrays prepared by through-mask electrochemical micromachining[J]. Precision Engineering, 2015, 39:204-211.
[5] JIN D S, CHUN K H, LEE E S. Analysis of the current density characteristics in through-mask electrochemical micromachining (TMEMM) for fabrication of micro-hole arrays on invar alloy film[J]. Chinese Journal of Aeronautics, 2017, 30(3):1231-1241.
[6] WANG D, ZHU Z, BAO J, et al. Reduction of stray corrosion by using iron coating in NaNO3 solution during electrochemical machining[J]. International Journal of Advanced Manufacturing Technology, 2015, 76(5-8):1365-1370.
[7] KERN P, VEH J, MICHLER J. New developments in through-mask electrochemical micromachining of titanium[J]. Journal of Micromechanics & Microengineering, 2007, 17(6):1168.
[8] BALDHOFF T, NOCK V, MARSHALL A T. Review-through-mask electrochemical micromachining[J]. Journal of the Electrochemical Society, 2018, 165(16):E841-E855.
[9] ZHOU X, QU N S,HOU Z B, et al. Electrochemical micromachining of microgroove arrays on phosphor bronze surface for improving the tribological performance[J]. Chinese Journal of Aeronautics, 2018, 31(7):1609-1618.
[10] BALDHOFF T, NOCK V, MARSHALL A T. Through-mask electrochemical micromachining of aluminum in phosphoric acid[J]. Journal of the Electrochemical Society, 2017, 164(9):E194-E202.
[11] COURTNEY D G, LI H, LOZANO P C. Electrochemical micromachining on porous nickel for arrays of electrospray ion emitters[J]. Journal of Microelectromechanical Systems, 2013, 22(2):471-482.
[12] KUNAR S, BHATTACHARYYA B. Electrochemical micromachining of micro square pattern using reusable masked tool[J]. Materials and Manufacturing Processes, 2019, 34(5):487-493.
[13] MAHATA S, KUNAR S, BHATTACHARYYA B. Micro dimple array fabrication by through mask electrochemical micromachining utilizing low-aspect ratio mask[J]. Journal of the Electrochemical Society, 2018, 165(3):E129-E137.
[14] WANG G Q, LI H S, QU N S, et al. Improvement of electrolyte flow field during through-mask electrochemical machining by changing mask wall angle[J]. Journal of Manufacturing Processes, 2017, 25:246-252.
[15] WANG G Q, LI H S, ZHANG C, et al. Improvement of machining consistency during through-mask electrochemical large-area machining[J]. Chinese Journal of Aeronautics, 2019, 32(4):1051-1058.
[16] ZHANG X F, LI H, YIN Z, et al. Influence of bubbles on micro-dimples prepared by electrochemical micromachining[J]. Journal of Applied Electrochemistry, 2019, 49:963-978.
[17] ZHAI K, DU L Q, WEN Y K, et al. Fabrication of micro pits based on megasonic assisted through-mask electrochemical micromachining[J]. Ultrasonics, 2020, 100:105990.
[18] ZHAO C H, MING P M, ZHANG X M, et al. Through-mask electrochemical micromachining with reciprocating foamed cathode[J]. Micromachines, 2020, 11(2):188.
[19] CHEN X L, DONG B Y, ZHANG C Y, et al. Jet electrochemical machining of micro dimples with conductive mask[J]. Journal of Materials Processing Technology, 2018, 257:101-111.
[20] LI H S, WANG G Q, QU N S, et al. Through-mask electrochemical machining of a large-area hole array in a serpentine flow channel[J]. The International Journal of Advanced Manufacturing Technology, 2017, 89:933-940.
[21] CHEN X L, FAN G C, LIN C H, et al. Investigation on the electrochemical machining of micro groove using masked porous cathode[J]. Journal of Materials Processing Technology, 2020, 276:116406.
CJA