利用高速风洞及压敏漆（PSP）技术，研究了端壁表面不同分腔流量比对端壁表面的气膜冷却效率的影响。对比各个分腔在不同流量比下端壁表面的气膜冷却效率的详细分布发现：端壁表面的气膜冷却效率随着槽缝流（分腔1）流量比的增加而增大，随着槽缝喷射冷气流量的增加，冷气在端壁表面的覆盖范围变广，同时冷却效果也有所提升；随着端壁前部分腔（分腔2）冷气流量比的增加，叶栅通道喉部上游区域的冷却流体会出现明显的吹离壁面的情况，端壁表面的气膜冷却效率也会随之减小；端壁后部分腔（分腔3）冷气流量比对端壁表面的冷却效率的影响与分腔2类似。
The effect of mass flow ratios different on the film cooling effectiveness of the enwall is studied using the Pressure-Sensitive Paint (PSP) technology and high-speed wind tunnel. The detailed distribution of the film cooling effectiveness on the endwall surface under different flow ratios of each cavity is obtained. The film cooling effectiveness on the endwall surface increases with the increase of the slot mass flow ratio. As the coolant injected into the slot increases, the coverage of the coolant on endwall surface becomes, cooling performance. As the coolant mass flow ratio of 2 increases, because the coolant from cooling holes liftoff from the wall surface to the excessively high speed. The influence of the mass flow ratio cavity 3 on the cooling effectiveness of the endwall is similar to that of cavity 2.
[1] BARIGOZZI G, BENZONI G, FRANCHINI G, et al. Fan-shaped hole effects on the aero-thermal performance of a film-cooled endwall[J]. Journal of Turbomachinery, 2006, 128(1):507-518.
[2] 刘存良, 朱惠人, 白江涛, 等. 基于瞬态液晶测量技术的收缩-扩张形孔气膜冷却特性[J]. 航空学报, 2009, 30(5):812-818. LIU C L, ZHU H R, BAI J T, et al. Film cooling characteristics of converging-expanding hole with transient liquid crystal measurement technique[J]. Acta Aeronautica et Astronautica Sinica, 2009, 30(5):812-818(in Chinese).
[3] RAVI B V, DESHPANDE S, RAMESH S, et al. Film cooling performance of tripod holes on the endwall upstream of a first stage nozzle guide vane[C]//ASME International Mechanical Engineering Congress & Exposition. New York:ASME,2015.
[4] 叶林,刘存良,杨寓全,等.V肋对尾缘劈缝气膜冷却特性影响的实验研究[J].航空学报, 2021, 42(4):124181. YE L, LIU C L, YANG Y Q, et al. Experimental study of the effect of v-shaped ribs on the film cooling characteristics for the trailing-edge cutback[J]. Acta Aeronautica et Astronautica Sinica, 2021, 42(4):124181(in Chinese).
[5] KOHLI A, BOGARD D G. Effects of very high free-stream turbulence on the jet-mainstream interaction in a film cooling flow[J]. Journal of Turbomachinery, 1998, 120(4):785-790.
[6] CHEN A F,SHIAU C C, HAN J C.Turbine blade platform film cooling with fan-shaped holes under simulated swirl purge flow and slashface leakage conditions:GT-2017-63119[R].New York:ASME, 2017.
[7] THRIFT A A, THOLE K A, HADA S. Effects of an axisymmetric contoured endwall on a nozzle guide vane:Adiabatic effectiveness measurements[J]. Journal of Turbomachinery, 2011,133(4):1617-1627.
[8] ZHANG L, YIN J, LIU K, et al. Effect of hole diameter on nozzle endwall film cooling and associated phantom cooling[C]//ASME Turbo Expo 2015:Turbine Technical Conference and Exposition. New York:ASME,2015.
[9] 张扬, 齐士博, 袁新. 涡轮流场影响端壁气膜冷却的实验研究[J]. 工程热物理学报, 2011, 32(6):941-944. ZHANG Y, QI S B, YUAN X.Experimental investigation on the turbine blade platform film cooling effected by the flow field[J]. Journal of Engineering Thermophysics, 2011, 32(6):941-944(in Chinese).
[10] SHIAU C C, CHEN A F, HAN J C, et al. Full-scale turbine vane endwall film-cooling effectiveness distribution using pressure-sensitive paint technique[J]. Journal of Turbomachinery,2016,138(5):051002.
[11] CHOWDHURY N H, SHIAU C C, HAN J C, et al. Film cooling effectiveness comparison on turbine vane endwall with cluster configurations using psp measurement technique[C]//ASME 2017 International Mechanical Engineering Congress and Exposition.New York:ASME,2017.
[12] LI M, LI X, REN J, et al. Overall cooling effectiveness characteristic and influence mechanism on an endwall with film cooling and impingement[C]//ASME Turbo Expo 2015:Turbine Technical Conference and Exposition. New York:ASME, 2015.
[13] ZHANG L J, JAISWAL R S. Turbine nozzle endwall film cooling study using pressure-sensitive paint[J]. Journal of Turbomachinery,2001,123(4):730-738.
[14] EL-GABRY L, XU H, LIU K, et al. Effect of coolant injection angle on nozzle endwall film cooling:Experimental and numerical analysis in linear cascade[C]//ASME Turbo Expo 2018:Turbomachinery Technical Conference and Exposition. New York:ASME, 2018.
[15] CHOWDHURY N H, SHIAU C C, HAN J C, et al. Turbine vane endwall film cooling with slashface leakage and discrete hole configuration[J]. Journal of Turbomachinery, 2017,139(6):1-13.
[16] CHOWDHURY N H, SHIAU C C, HAN J C, et al. Turbine vane endwall film cooling study from axial-row configuration with simulated upstream leakage flow[C]//ASME Turbo Expo 2017:Turbomachinery Technical Conference and Exposition. New York:ASME, 2017.
[17] ORNANO F, POVEY T. Experimental and computational study of the effect of momentum-flux ratio on high pressure ngv endwall cooling systems[C]//ASME Turbo Expo 2017:Turbomachinery Technical Conference and Exposition. New York:ASME, 2017.
[18] KLINE S J, MCCLINTOCK F A. Describing uncertainties in single-sample experiments[J].Journal of Mechanical Engineering, 1953, 75:3-8.
[19] WRIGHT L M, MCCLAIN S T, CLEMENSON M D. Effect of density ratio on flat plate film cooling with shaped holes using PSP[C]//ASME Turbo Expo 2010:Power for Land, Sea, and Air. New York:ASME, 2010.
CJA