马赫数可控的方转圆内收缩进气道非设计点工作特性

doi:10.7527/S1000-6893.2016.0060

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

马赫数可控的方转圆内收缩进气道非设计点工作特性

李永洲^1,2, 张堃元¹, 孙迪³

1. 南京航空航天大学能源与动力学院, 南京 210016;
2. 中国航天科技集团公司西安航天动力研究所, 西安 710100;
3. 中国航天科技集团公司西安航天动力技术研究所, 西安 710025

收稿日期:2015-11-02 修回日期:2016-03-01 出版日期:2016-11-15 发布日期:2016-03-08
通讯作者: 李永洲,男,博士,工程师。主要研究方向:高超声速推进技术和内流气体动力学。Tel.:029-85208061,E-mail:nuaa-2004@126.com E-mail:nuaa-2004@126.com
作者简介:李永洲,男,博士,工程师。主要研究方向:高超声速推进技术和内流气体动力学。Tel.:029-85208061,E-mail:nuaa-2004@126.com;张堃元,男,硕士,教授,博士生导师。主要研究方向:高超声速推进技术和内流气体动力学。Tel.:025-84892201-2100,E-mail:zkype@nuaa.edu.cn;孙迪,女,硕士,工程师。主要研究方向:高超声速气动热动力学。Tel.:029-85208061,E-mail:sinda.y@163.com
基金资助:
国家自然科学基金（90916029，91116001）

Off-design performance characteristics of inward turning inlet with rectangular-to-circular shape transition with controlled Mach number distribution

LI Yongzhou^1,2, ZHANG Kunyuan¹, SUN Di³

1. College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China;
2. Xi'an Aerospace Propulsion Institute, China Aerospace Science and Technology Corporation, Xi'an 710100, China;
3. Xi'an Institute of Aerospace Propulsion Technology, China Aerospace Science and Technology Corporation, Xi'an 710025, China

Received:2015-11-02 Revised:2016-03-01 Online:2016-11-15 Published:2016-03-08
Supported by:
National Natural Science Foundation of China (90916029, 91116001)

摘要/Abstract

摘要：

基于反正切马赫数分布的弥散反射激波中心体轴对称基准流场，设计了方转圆内收缩进气道，并对其进行风洞试验和数值仿真研究，获得该进气道非设计点（Ma=5.0和Ma=7.0）的工作特性和自起动特性。试验结果表明：进气道顶板压力分布具有反正切曲线特征，出口涡流区小且总体性能优良。Ma=5.0和Ma=7.0时出口总压恢复系数分别为0.647和0.443，对应的增压比分别为20.0和32.7。Ma=5.0时，进气道不但可以捕获约90%的自由来流，而且能够自起动（内收缩比高于Kantrowitz限制），下临界反压为64倍来流静压，对应的出口马赫数和总压恢复系数分别为1.32和0.409。上述结果表明，本文设计方法可以获得高性能的矩形转圆内收缩进气道。

关键词: 内收缩进气道, 基准流场, 马赫数分布规律, 风洞试验, 自起动

Abstract:

Based on the axisymmetric basic flowfield of diffusing reflected shock center body with arc tangent Mach number distribution, an inward turning inlet with rectangular-to-circular shape transition is designed. Wind tunnel experiment and numerical simulation are conducted to obtain the off-design performance characteristics and self-starting characteristics. The experimental results indicate that the top wall pressure distribution is of arc tangent curve. The inlet has good overall performance and small vortex region at exit section. For Ma=5.0 and Ma=7.0, the total pressure recovery coefficient of exit section is 0.647 and 0.443, respectively, and the corresponding compression ratio is 20.0 and 32.7, respectively. For Ma=5.0, the inlet could capture about 90% of the free stream and self-start despite its internal contraction ratio being above the Kantrowitz limit; the lower critical back pressure of the inlet is about 64 times of the free stream static pressure, and the corresponding Mach number and total pressure recovery coefficient of exit section are 1.32 and 0.409, respectively. The results demonstrate that high-performance inward turning inlets with rectangular-to-circular shape transition can be designed by the method proposed in this paper.

Key words: inward turning inlets, basic flowfield, Mach number distribution, wind tunnel test, self-starting

中图分类号:

V231.3

李永洲, 张堃元, 孙迪. 马赫数可控的方转圆内收缩进气道非设计点工作特性[J]. 航空学报, 2016, 37(11): 3263-3272.

LI Yongzhou, ZHANG Kunyuan, SUN Di. Off-design performance characteristics of inward turning inlet with rectangular-to-circular shape transition with controlled Mach number distribution[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2016, 37(11): 3263-3272.

参考文献

[1] YOU Y C. An overview of the advantages and concerns of hypersonic inward turning inlets:AIAA-2011-2269[R]. Reston:AIAA, 2011.
[2] BILLIG F S, KOTHARI A. Streamline tracing:Technique for designing hypersonic vehicles[J]. Journal of Propulsion and Power, 2000, 16(3):465-471.
[3] TIAN C, LI N, GONG G H, et al. A parameterized geometry design method for inward turning inlet compatible waverider[J]. Chinese Journal of Aeronautics, 2013, 26(5):1135-1146.
[4] MALO-MOLINA F J, GAITONDE D V, EBRAHIMI H B, et al. Three-dimensional analysis of a supersonic combustor coupled to innovative inward-turning inlets[J]. AIAA Journal,2010, 48(3):572-582.
[5] BULMAN M J, SIEBENHAAR A. The rebirth of round hypersonic propulsion:AIAA-2006-5035[R]. Reston:AIAA, 2006.
[6] BILLIG F S, JACOBSEN L S. Comparison of planar and axisymmetric flow paths for hydrogen fueled space access vehicle:AIAA-2003-4407[R]. Reston:AIAA, 2003.
[7] SMART M K. Design of three-dimensional hypersonic inlets with rectangular-to-elliptical shape transition[J]. AIAA Journal of Power and Propulsion, 1999, 15(3):408-416.
[8] SMART M K. Experimental testing of a hypersonic inlet with rectangular-to-elliptical shape transition:AIAA-1999-0085[R]. Reston:AIAA, 1999.
[9] GOLLAN R J, FERLEMANN P G. Investigation of REST-class hypersonic inlet designs:AIAA-2011-2254[R]. Reston:AIAA, 2011.
[10] SABEAN J W, LEWIS M J. Computational optimization of a hypersonic rectangular-to-circular inlet[J]. Journal of Propulsion and Power, 2001, 17(3):571-578.
[11] TAYLOR T, VAN WIE D. Performance analysis of hypersonic shape-changing inlets derived from morphing streamline traced flowpaths:AIAA-2008-2635[R]. Reston:AIAA, 2008.
[12] YOU Y C, LIANG D W, GUO R W. High enthalpy wind tunnel tests of three-dimensional section controllable internal waverider hypersonic inlet:AIAA-2009-0031[R]. Reston:AIAA, 2009.
[13] XIAO Y B, YUE L J, CHEN L H, et al. Iso-contraction-ratio methodology for the design of hypersonic inward turning inlets with shape transition:AIAA-2012-5978[R]. Reston:AIAA, 2012.
[14] 南向军, 张堃元, 金志光, 等. 矩形转圆形进气道马赫5正8° 攻角启动性能分析[J]. 南京航空航天大学学报, 2012, 44(2):146-151. NAN X J, ZHANG K Y, JIN Z G, et al. Start characteristics of hypersonic inlets with rectangular to circular shape transition at Ma5 with attack angle 8°[J]. Journal of Nanjing University of Aeronautics and Astronautics, 2012, 44(2):146-151(in Chinese).
[15] MÖLDER S, SZPIRO J. Busemman inlet for hypersonic speeds[J]. Journal of Spacecraft and Rockets, 1966, 3(8):1303-1304.
[16] 贺旭照, 乐嘉陵, 宋文燕, 等. 基于轴对称喷管的三维内收缩进气道的设计与初步评估[J]. 推进技术, 2010, 31(2):147-152. HE X Z, LE J L, SONG W Y, et al. 3D inward turning inlet design basing on axisymmetric nozzle and its preliminary assessment[J]. Journal of Propulsion Technology, 2010, 31(2):147-152(in Chinese).
[17] 李永洲, 张堃元, 孙迪. 马赫数可控的方转圆高超声速内收缩进气道试验研究[J]. 航空学报, 2016, 37(10):2970-2979. LI Y Z, ZHANG K Y, SUN D. Experimental investigation on a hypersonic inward turning inlet of rectangular-to-circular shape transition with controlled Mach number distribution[J]. Acta Aeronautica et Astronamtica Sinica, 2016, 37(10):2970-2979(in Chinese).
[18] 李永洲, 张堃元, 罗蕾, 等. 高超声速内收缩进气道轴对称基准流场改进[J]. 航空动力学报, 2013, 28(11):2543-2552. LI Y Z, ZHANG K Y, LUO L, et al. Modified axisymmetric basic flowfield for hypersonic inward turning inlet[J]. Journal of Aerospace Power, 2013, 28(11):2543-2552(in Chinese).
[19] KANTROWITZ A, DONALDSON C. Preliminary investigation of supersonic diffusers:NACA-WR L-713[R]. Reston:NASA, 1945.
[20] REINARTZ B U, HERRMANN C D, BALLMANN B, et al. Aerodynamic performance analysis of a hypersonic inlet isolator using computation and experiment[J]. Journal of Propulsion and Power, 2003, 19(5):868-875.
[21] 王翼. 高超声速进气道启动问题研究[D]. 长沙:国防科学技术大学, 2008. WANG Y. Investigation on the starting characteristics of hypersonic inlet[D]. Changsha:National University of Defense Technology, 2008(in Chinese).
[22] 刘凯礼. 高超声速进气道动/稳态攻角特性研究[D]. 南京:南京航空航天大学,2012. LIU K L. Research on aerodynamic characteristics of hypersonic inlets with dynamic/steady angle-of-attack[D]. Nanjing:Nanjing university of Aeronautics and Astronautics, 2012(in Chinese).
[23] KITAMURA E, MITANI T, SAKURANAKA N, et al. Evaluating the aerodynamic performance of scramjet engines by pressure measurement:AIAA-2003-7053[R]. Reston:AIAA, 2003.
[24] 王红, 马明明. 某型发动机空气流量计算影响因素研究[J]. 燃气涡轮试验与研究, 2010, 23(3):22-26. WANG H, MA M M. Study on the factors affecting airflow calculation of an aero-engine[J]. Gas Turbine Experiment and Research, 2010, 23(3):22-26(in Chinese).
[25] VAN WIE D M, KWOK F T, WALSH R F. Starting characteristics of supersonic inlets:AIAA-1996-2914[R]. Reston:AIAA, 1996.

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

马赫数可控的方转圆内收缩进气道非设计点工作特性

Off-design performance characteristics of inward turning inlet with rectangular-to-circular shape transition with controlled Mach number distribution

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	孙朋朋, 刘平安, 樊枫, 曾伟. 悬停状态共轴刚性旋翼机身气动干扰特性[J]. 航空学报, 2024, 45(9): 529284-529284.
[2]	王畅, 何龙, 徐栋霞, 唐敏, 马率, 吴希明. 共轴刚性旋翼桨毂流动控制减阻研究[J]. 航空学报, 2024, 45(9): 529084-529084.
[3]	张卫国, 唐敏, 武杰, 彭先敏, 章贵川, 聂博文, 王亮权, 李超群. 倾转旋翼机风洞试验综述[J]. 航空学报, 2024, 45(9): 530114-530114.
[4]	聂博文, 王亮权, 黄志银, 何龙, 杨仕鹏, 颜鸿涛, 章贵川. 复合式高速无人直升机飞行动力学建模与控制策略设计[J]. 航空学报, 2024, 45(9): 529848-529848.
[5]	刘柳, 向先宏, 张宇飞, 陈海昕, 魏闯, 朱剑, 杨普. 一种高升阻比非常规翼身融合燕尾气动布局[J]. 航空学报, 2024, 45(6): 629630-629630.
[6]	李海星, 周峰, 颜巍, 白峰, 赵克良. 砂纸冰对民机平尾气动特性的影响[J]. 航空学报, 2024, 45(2): 128657-128657.
[7]	李学良, 李创创, 苏伟, 吴杰. 分布式粗糙元对高超声速边界层不稳定性的影响试验[J]. 航空学报, 2024, 45(2): 128627-128627.
[8]	刘宇, 秦梦婕, 王强, 易贤. 含盐海水飞沫的结冰风洞试验相似准则[J]. 航空学报, 2023, 44(S2): 729297-729297.
[9]	杨秋明, 朱永峰, 陈华伟, 刘晓林. 镂空图案化电加热组件防冰性能试验研究[J]. 航空学报, 2023, 44(S2): 729334-729334.
[10]	高世琦, 丁博, 解旭祯, 李铮, 陈林, 钱首元, 焦子涵, 白光辉. 等离子体激励在高速流动中的减阻机制[J]. 航空学报, 2023, 44(S2): 729373-729373.
[11]	许岭松, 吴渊, 朱东宇, 张付昆, 刘昱. FL⁃61结冰风洞翼型俯仰振荡机构研制[J]. 航空学报, 2023, 44(S2): 729296-729296.
[12]	金毅, 孙姝, 郭赟杰, 谭慧俊, 张悦. 超声速可调进气道内流双解现象及其节流特性[J]. 航空学报, 2023, 44(7): 127134-127134.
[13]	李俊红, 靳旭红, 刘春风, 苗文博, 程晓丽. 临近空间高速飞行器微量气动力试验及计算[J]. 航空学报, 2023, 44(6): 127072-127072.
[14]	曾宪昂, 赵冬强, 李俊杰, 严泽洲, 刘成玉. 弹性机翼阵风减缓控制策略风洞试验[J]. 航空学报, 2023, 44(4): 226869-226869.
[15]	刘畅, 张耘隆, 闫指江, 赵磊, 季辰. 锤头体火箭弹性模型脉动压力风洞试验[J]. 航空学报, 2023, 44(23): 128384-128384.