航空学报 > 2014, Vol. 35 Issue (8): 2341-2347   doi: 10.7527/S1000-6893.2013.0438

铝合金薄板零件橡皮囊成形屈曲分析与实验

涂集林, 王永军, 张纪春, 吴建军, 魏生民   

  1. 西北工业大学 陕西省数字化制造工程技术研究中心, 陕西 西安 710072
  • 收稿日期:2013-09-10 修回日期:2013-10-17 出版日期:2014-08-25 发布日期:2013-10-21
  • 通讯作者: 王永军,Tel.:029-88493717,E-mail:wyongjun@nwpu.edu.cn E-mail:wyongjun@nwpu.edu.cn
  • 作者简介:涂集林男,博士研究生。主要研究方向:薄板成形,金属塑性成形。E-mail:tttjlin@mail.nwpu.edu.cn;王永军男,博士,副教授,硕士生导师。主要研究方向:金属塑性成形,复合材料成形。Tel:029-88493717,E-mail:wyongjun@nwpu.edu.cn;张纪春男,硕士研究生。主要研究方向:金属塑性成形,钛合金成形。E-mail:sishaoyezhang@163.com;吴建军男,博士,教授,博士生导师。主要研究方向:材料成形的数字化分析与模拟,工装结构分析与优化,复材预成形与制造。E-mail:wujj@nwpu.edu.cn;魏生民男,博士,教授,博士生导师。主要研究方向:现代集成制造技术,科学计算可视化及虚拟现实技术。E-mail:weism@nwpu.edu.cn
  • 基金资助:

    国家自然科学基金(51075332)

Analysis and Experiment on Buckling of Rubber Bladder Forming of Thin Aluminum Alloy Plate Parts

TU Jilin, WANG Yongjun, ZHANG Jichun, WU Jianjun, WEI Shengmin   

  1. Shaanxi Province Engineering Research Center for Digital Manufacturing Technology, Northwestern Polytechnical University, Xi'an 710072, China
  • Received:2013-09-10 Revised:2013-10-17 Online:2014-08-25 Published:2013-10-21
  • Supported by:

    National Natural Science Foundation of China (51075332)

摘要:

为了抑制铝合金薄板类零件在橡皮囊成形后出现屈曲的缺陷,采用薄板屈曲微分方程对零件成形后的屈曲进行理论分析,并通过橡皮囊成形实验研究自然时效时间和成形压力对屈曲缺陷的影响。理论分析结果表明:零件法兰屈曲波数与其内外径比有关,通过改变法兰宽度进行实验验证,实验结果与理论分析结果相符;而成形实验结果表明,屈曲缺陷高度随板料自然时效时间的增加而增加,随成形压力的增加而减少。因此,理论分析结果有效,并且可通过减少淬火后成形时间和增加成形压力来抑制屈曲缺陷。

关键词: 铝合金, 薄板, 橡皮囊成形, 法兰屈曲, 时效时间, 屈曲波数

Abstract:

In order to restrain the buckling defects of the thin aluminum alloy plate parts after the process of rubber bladder forming, the buckling process is theoretically analyzed using thin plate buckling differential equations, and the effects of natural aging time and forming pressure on buckling defects are studied through the rubber bladder forming experiment. The results show that the flange buckling wave number has the relationship with the diameter ratio, and the forming experiment results with different flange widths show that the flange wave number agrees with the theoretical calculated results, the buckling defect height increases with the increase of the natural aging time, and decreases with the increase of the forming pressure. Therefore, the results of the theoretical analysis is valid, and the buckling defects can be restrained by reducing forming time after quenching and increasing forming pressure.

Key words: aluminum alloys, thin plate, rubber bladder forming, flange buckling, aging time, buckling wave number

中图分类号: