多级刷式密封级间压降分配影响因素数值与实验研究

doi:10.7527/S1000-6893.2019.23544

流体力学与飞行力学

本期目录 | 过刊浏览 | 高级检索

前一篇 | 后一篇

多级刷式密封级间压降分配影响因素数值与实验研究

赵欢¹, 焦忠泽¹, 孙丹¹, 刘永泉^2,3, 战鹏^2,3, 信琦^2,3

1. 沈阳航空航天大学航空发动机学院, 沈阳 110136;
2. 中国航发沈阳发动机研究所, 沈阳 110015;
3. 中国航发航空发动机动力传输航空科技重点实验室, 沈阳 110015

收稿日期:2019-10-08 修回日期:2020-02-07 发布日期:2020-02-06
通讯作者: 孙丹 E-mail:phd_sundan@163.com
基金资助:
国家自然科学基金（51675351）；中国博士后科学基金（2018M633572）；辽宁省高等学校创新人才支持计划项目（LR2016033）

Numerical and experimental research on interstage pressure drop distribution affecting factors of multi-stage brush seals

ZHAO Huan¹, JIAO Zhongze¹, SUN Dan¹, LIU Yongquan^2,3, ZHAN Peng^2,3, XIN Qi^2,3

1. School of Aero-engine, Shenyang Aerospace University, Shenyang 110136, China;
2. Shenyang Engine Design and Research Institute, Aero Engine(Group) Corporation of China, Shenyang 110015, China;
3. Key Lab for Power Transmission of Aero Engine, Aero Engine(Group) Corporation of China, Shenyang 110015, China

Received:2019-10-08 Revised:2020-02-07 Published:2020-02-06
Supported by:
National Natural Science Foundation of China (51675351); China Postdoctoral Science Foundation (2018M633572); College Innovation Talent Support Program of Liaoning Province (LR2016033)

摘要/Abstract

摘要： 多级刷式密封级间压降分配直接影响刷式密封的封严特性和使用寿命，现有多级刷式密封结构存在各级压降不均衡导致密封提前失效的问题。本文建立多级刷式密封三维实体流固耦合求解模型，设计搭建多级刷式密封实验装置，在数值计算与实验测试结果相互验证的基础上，研究了工况参数与结构参数对多级刷式密封级间压降分配的影响规律，揭示了多级刷式密封级间压降不均衡性的产生机理。研究结果表明：在本文研究工况下，相同结构的两级刷式密封各级压降占比分别为32%~35%和65%~68%，三级刷式密封各级压降占比分别为21%~27%、27%~32%、41%~52%，多级刷式密封各级承担压降逐级增大，进出口压比对级间压降分配影响不大；增大刷丝束与转子表面间径向间隙、刷丝之间间隙以及后挡板高度均可改善各级压降分配，同时也会增加泄漏量；影响多级刷式密封级间压降均衡性的主要原因是逐级不均匀增大的体积流量，各级压降随体积流量逐级不均匀的增加而增大；增大下游级流道截面积可有效降低体积流量，平衡多级刷式密封各级压降。本文研究结果为多级刷式密封结构设计提供了理论依据。

关键词: 多级刷式密封, 级间压降分配, 三维实体建模, 流固耦合, 级间压降不均衡

Abstract: The pressure drop distribution between the multi-stage brush seals directly affects the seal characteristics and the service life of the brush seals. The existing multi-stage brush seals structure have the problem that the pressure drop is unbalanced at different stages, leading to premature seal failure. In this paper, a three-dimensional fluid-solid interaction multi-stage brush seals model is established, and a multi-stage brush seals experimental device is designed. Based on the mutual verification of numerical calculation and experimental test results, the influence law of working condition parameters and structural parameters on the interstage pressure drop distribution of multi-stage brush seals is investigated. The mechanism of interstage pressure drop imbalance of multi-stage brush seals is revealed. The results show that under the research conditions in this paper, the pressure drop ratio of the two-stage brush seals of the same structure are 32%-35% and 65%-68%, and the pressure drop ratio of the three-stage brush seals are different:21%-27%, 27%-32%, 41%-52%. The pressure drop of the multi-stage brush seals is gradually increased, and the pressure ratio of the inlet and outlet has little effect on the distribution of interstage pressure drop. By increasing the radial gap between the bristle tow and the rotor surface, the gap between the bristles and the height of the backplate can improve the pressure drop distribution of each level, and the amount of leakage will also increase. The main reason that affects the pressure drop balance of the multi-stage brush seals is the uneven increase of volume flow rate step by step, and the pressure drop of each stage increases with the increase of the volume flow unevenness step by step. Increasing the cross-sectional area of the downstream level can effectively reduce the volume flow rate and balance the pressure drop between multi-stage brush seals. The research results in this paper provide a theoretical basis for the design of multi-stage brush seals structure.

Key words: multi-stage brush seals, interstage pressure drop distribution, three-dimensional modeling, fluid-solid interactions, interstage pressure drop imbalance

中图分类号:

V231

赵欢, 焦忠泽, 孙丹, 刘永泉, 战鹏, 信琦. 多级刷式密封级间压降分配影响因素数值与实验研究[J]. 航空学报, 2020, 41(10): 123544-123544.

ZHAO Huan, JIAO Zhongze, SUN Dan, LIU Yongquan, ZHAN Peng, XIN Qi. Numerical and experimental research on interstage pressure drop distribution affecting factors of multi-stage brush seals[J]. ACTA AERONAUTICAET ASTRONAUTICA SINICA, 2020, 41(10): 123544-123544.

参考文献

[1] 李军, 李志刚, 张元桥, 等. 刷式密封技术的研究进展[J].航空发动机, 2019, 45(2):74-84. LI J, LI Z G, ZHANG Y Q, et al. Research progress of brush seal technology[J].Aeroengine, 2019, 45(2):74-84(in Chinese).
[2] DIN S, DEMIROGLU M, YURNQUIST N, et al. Fundamental design issues of brush seals for industrial applications[J].Journal of Turbomachinery,2002,124(2):293-300.
[3] CHUPP R E, GHASRIPOOR F, TURNQUIST N, et al. Advanced seals for industrial turbine applications:dynamics seal development[J].Journal of Propulsion and Power,2002, 18(2):1260-1266.
[4] 吴施志, 江平, 力宁, 等. 刷式密封摩擦生热温度场数值计算及试验[J].航空动力学报, 2019, 34(4):737-743. WU S Z, JIANG P, LI N, et al. Numerical calculation and experiment on temperature field of friction heat generation of brush seal[J].Journal of Aerospace Power, 2019, 34(4):737-743(in Chinese).
[5] 黄首清, 索双富, 李永健, 等. 刷式密封流场和温度场的3维数值计算[J].清华大学学报(自然科学版), 2014, 54(6):805-810. HUANG S Q, SUO S F, LI Y J, et al. Numerical predictions of the flow and temperature distributions in a threedimensional brush seal model[J].Journal of Tsinghua University (Science and Technology), 2014, 54(6):805-810(in Chinese).
[6] 邱波, 李军. 基于多孔介质局部非热平衡方法的刷式密封耦合传热特性[J].航空动力学报, 2015, 30(5):1067-1075. QIU B, LI J. Conjugate heat transfer characteristics of brush seal based on local thermal non-equilibrium porous medium approach[J].Journal of Aerospace Power, 2015, 30(5):1067-1075(in Chinese).
[7] 邱波, 李军, 丰镇平. 考虑刷丝变形的刷式密封摩擦热效应研究[J].工程热物理学报, 2013, 34(11):2030-2034. QIU B, LI J, FENG Z P. Investigations on frictional heat generation of brush seals with consideration of bristle deflections[J].Journal of Engineering Thermophysics, 2013, 34(11):2030-2034(in Chinese).
[8] 刘璐园, 张元桥, 李军. 基于流固耦合方法的刷式密封刷丝变形及接触力特性的数值研究[J].燃气轮机技术, 2019, 32(1):1-7. LIU L Y, ZHANG Y Q, LI J. Numerical investigations on the bristle deformation and contact force characteristics of brush seals using fluid-structure coupling method[J].Gas Turbine Technology, 2019, 32(1):1-7(in Chinese).
[9] PUGACHEV A O, DECKNER M. Experimental and theoretical rotordynamic stiffness coefficients for a three-stage brush seal[J].Mechanical Systems and Signal Processing, 2012, 31:143-154.
[10] 王凯杰, 杨义勇, 索双富, 等. 两级刷式密封的流动计算与系统参数的配置研究[J].润滑与密封, 2017, 42(10):43-47. WANG K J, YANG Y Y, SUO S F, et al. Analysis on flows of two-stage brush seals and research on configuration of system parameters[J].Lubrication Engineering, 2017, 42(10):43-47(in Chinese).
[11] 文龙, 王之栎, 丁蕾, 等. 双级低滞后刷式密封级间不均衡性分析[J].北京航空航天大学学报, 2014, 40(8):1154-1159. WEN L, WANG Z L, DING L, et al. Inter-stage imbalance analysis of two-stage low hysteresis brush seal[J].Journal of Beijing University of Aeronautics and Astronautics, 2014, 40(8):1154-1159(in Chinese).
[12] 文龙, 王之栎. 双级低滞后刷式密封的温度场分析[J].中国新技术新产品, 2013(23):2-4. WEN L, WANG Z L. Temperature field analysis of two-stage low hysteresis brush seal[J].China New Technologies and Products, 2013(23):2-4(in Chinese).
[13] RABEN M, FRIEDRICHS J, HELMIS T, et al. Brush seals used in steam environments-chronological wear development and the impact of different seal designs[J].Journal of Engineering for Gas Turbines and Power, 2016, 139(5):051901.
[14] RABEN M, FRIEDRICHS J, FLEGLER J. Brush seal frictional heat generation-test rig design and validation under steam environment[J].Journal of Engineering for Gas Turbines and Power, 2016, 139(3):032502.
[15] 邱波, 李军, 冯增国, 等. 两级刷式密封泄漏特性的实验与数值研究[J].西安交通大学学报, 2013, 47(7):7-12. QIU B, LI J, FENG Z G, et al. Experimental and numerical investigations of the leakage characteristics of two-stage brush seal[J].Journal of Xi'an Jiaotong University, 2013, 47(7):7-12(in Chinese).
[16] 邱波, 李军. 刷式密封传热特性研究[J].西安交通大学学报, 2011, 45(9):99-105. QIU B, LI J. Investigation on the heat transfer characteristics of brush seals[J].Journal of Xi'an Jiaotong University, 2011, 45(9):99-105(in Chinese).
[17] 郎达学, 苏华. 表面织构靴底流体动压指尖密封的性能分析[J].航空学报, 2012, 33(8):1540-1546. LANG D X, SU H. Performance analysis of surface texture padded finger seal[J].Acta Aeronautica et Astronautica Sinica, 2012, 33(8):1540-1546(in Chinese).
[18] 王福军. 计算流体动力学分析[M]. 北京:清华大学出版社, 2004:34-36. WANG F J. Computational fluid dynamics analysis[M]. Beijing:Tsinghua University Press, 2004:34-36(in Chinese).
[19] 刘占生, 叶建槐. 刷式密封接触动力学特性研究[J].航空动力学报, 2002, 17(5):636-640. LIU Z S, YE J H. Research on structural dynamic characteristics of brush seals[J].Journal of Aerospace Power, 2002, 17(5):636-640(in Chinese).
[20] 王喜春, 苏华, 宗兆科. 周向收敛型动压式指尖密封的结构优化及其动态性能仿真[J].航空学报, 2011, 32(2):360-367. WANG X C, SU H, ZONG Z K. Structural optimization and dynamic simulation of circumferential convergent hydrodynamic finger seal[J].Acta Aeronautica et Astronautica Sinica, 2011, 32(2):360-367(in Chinese).
[21] 孙丹, 刘宁宁, 胡广阳, 等. 考虑刷丝变形的刷式密封流场特性与力学特性流固耦合研究[J].航空动力学报, 2016, 31(10):2544-2553. SUN D, LIU N N, HU G Y, et al. Fluid-structure interaction investigation on the flow field and mechanical characteristic in brush seal with bristle deflections[J].Journal of Aerospace Power, 2016, 31(10):2544-2553(in Chinese).
[22] 孙丹, 卢江, 刘永泉, 等. 篦齿封严风阻温升特性研究[J].航空学报, 2018, 39(11):122348. SUN D, LU J, LIU Y Q, et al. Investigation on windage heating characteristics of labyrinth seals[J].Acta Aeronautica et Astronautica Sinica, 2018, 39(11):122348(in Chinese).
[23] BORGUETA S J, BACH N R, CORREIA J J, et al.. Aerodynamic flutter of turbine brush seals:IMECE2017-73500[R]. New York:ASME, 2017.
[24] 张元桥, 闫嘉超, 李军. 考虑闭合效应的刷式密封泄漏特性研究[J].润滑与密封, 2017, 42(4):36-42. ZHANG Y Q, YAN J C, LI J. Investigations on leakage flow characteristics of brush seal with consideration of blow down effect[J].Lubrication Engineering, 2017, 42(4):36-42(in Chinese).

E-mail：hkxb@buaa.edu.cn

关于我们

期刊社服务

专业学科

封面文章

友情链接

主管单位：中国科学技术协会主办单位：中国航空学会北京航空航天大学

多级刷式密封级间压降分配影响因素数值与实验研究

Numerical and experimental research on interstage pressure drop distribution affecting factors of multi-stage brush seals

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	汪博, 高培鑫, 马辉, 孙伟, 林君哲, 李晖, 韩清凯, 刘中华. 航空发动机管路系统动力学特性综述[J]. 航空学报, 2022, 43(5): 25332-025332.
[2]	童明波, 陈吉昌, 李乐, 肖天航, 古彪, 董登科, 汪正中. 飞行器水载荷结构完整性数值模拟现状与展望-Part I:水上迫降和水上漂浮[J]. 航空学报, 2021, 42(5): 524530-524530.
[3]	胡文刚, 林长亮, 王刚, 门坤发. 多欧拉域耦合法在平尾鸟撞中的应用[J]. 航空学报, 2020, 41(1): 222860-222860.
[4]	邱滋华, 徐敏, 张斌, 梁春雷. 适用于涡激振荡问题研究的并行高精度方法[J]. 航空学报, 2019, 40(3): 122483-122483.
[5]	杨尚霖, 陈晓峰, 杜发喜, 雷忠琦, 姚小虎. 机动行为下飞机油箱晃动流固耦合动力学分析[J]. 航空学报, 2019, 40(3): 222471-222471.
[6]	黄江涛, 周铸, 刘刚, 高正红, 黄勇, 王运涛. 飞行器气动/结构多学科延迟耦合伴随系统数值研究[J]. 航空学报, 2018, 39(5): 121731-121731.
[7]	张伟伟, 高弈奇, 全金楼, 苏丹. 失谐叶栅的受迫振动响应特性分析[J]. 航空学报, 2017, 38(9): 521018-521018.
[8]	张帆, 郑津洋, 马利. 内压作用下的航空轮胎爆破碎片动力响应[J]. 航空学报, 2017, 38(8): 221032-221032.
[9]	李映坤, 韩珺礼, 陈雄, 周长省, 巩伦昆. 基于多物理场耦合的双脉冲发动机点火过程数值模拟[J]. 航空学报, 2017, 38(4): 120409-120409.
[10]	王运涛, 孙岩, 孟德虹, 张书俊, 杨小川. 包含支撑装置和机翼变形的CRM-WB构型气动特性数值模拟[J]. 航空学报, 2017, 38(10): 121202-121202.
[11]	胡国暾, 杜林, 孙晓峰. 基于浸入式边界法的叶栅颤振数值模拟[J]. 航空学报, 2015, 36(7): 2269-2278.
[12]	李伟, 马宝峰. 一种改进型松耦合方法在机翼摇滚计算中的应用[J]. 航空学报, 2015, 36(6): 1805-1813.
[13]	胡国暾, 杜林, 孙晓峰. 基于浸入式边界法的振荡转子叶片数值模拟[J]. 航空学报, 2014, 35(8): 2112-2125.
[14]	刘君, 徐春光, 张帆. 电磁阀颤振的流固耦合模拟研究[J]. 航空学报, 2014, 35(7): 1922-1930.
[15]	安伟刚, 梁生云, 陈殿宇. 一种局部动态数据交换方法在流固耦合分析中的应用[J]. 航空学报, 2013, 34(3): 541-546.